Item | Values | Description | ||
|
|
|
|
|
| PING TEST |
|
| Check network communications. This test |
|
|
|
| sends |
|
|
|
| host, then waits for an appropriate response. |
|
|
|
| To run a ping test, set the following items: |
|
|
|
|
|
|
| DEST TYPE | IPV4 | Specify whether the target product is an IPv4 |
|
|
| IPV6 | or IPv6 node. |
|
|
|
| |
|
|
|
|
|
|
| DEST IPV4 |
| Type the IPv4 address. |
|
|
|
|
|
|
| DEST IPV6 |
| Type the IPv6 address. |
|
|
|
|
|
|
| PACKET SIZE |
| Specify the size of each packet, in bytes, to |
|
|
|
| be sent to the remote host. The minimum is |
|
|
|
| 64 (default) and the maximum is 2048. |
|
|
|
|
|
|
| TIMEOUT |
| Specify the length of time, in seconds, to wait |
|
|
|
| for a response from the remote host. The |
|
|
|
| default is 1 and the maximum is 100. |
|
|
|
|
|
|
| COUNT |
| Specify the number of ping test packets to |
|
|
|
| send for this test. Select a value from 0 to 100. |
|
|
|
| The default is 4. To configure the test to run |
|
|
|
| continuously, select 0. |
|
|
|
|
|
|
| PRINT RESULTS | YES | If the ping test was not set for continuous |
|
|
| NO* | operation, you can print the test results. |
|
|
|
| |
|
|
|
|
|
|
| EXECUTE | YES | Specify whether to initiate the ping test. |
|
|
| NO* |
|
|
|
|
|
|
| PING RESULTS |
|
| View the ping test status and results on the |
|
|
|
| control panel display. You can select the |
|
|
|
| following items: |
|
|
|
|
|
|
| PACKETS SENT |
| Shows the number of packets (0 - 65535) |
|
|
|
| sent to the remote host since the most recent |
|
|
|
| test was initiated or completed. The default is |
|
|
|
| 0. |
|
|
|
|
|
|
| PACKETS |
| Shows the number of packets (0 - 65535) |
|
| RECEIVED |
| received from the remote host since the most |
|
|
|
| recent test was initiated or completed. The |
|
|
|
| default is 0. |
|
|
|
|
|
|
| PERCENT LOST |
| Shows the percent (0 to 100) of ping test |
|
|
|
| packets that were sent with no response from |
|
|
|
| the remote host since the most recent test |
|
|
|
| was initiated or completed. The default is 0. |
|
|
|
|
|
|
| RTT MIN |
| Shows the minimum detected |
|
|
|
| time (RTT), from 0 to 4096 milliseconds, for |
|
|
|
| packet transmission and response. The |
|
|
|
| default is 0. |
|
|
|
|
|
|
| RTT MAX |
| Shows the maximum detected |
|
|
|
| time (RTT), from 0 to 4096 milliseconds, for |
|
|
|
| packet transmission and response. The |
|
|
|
| default is 0. |
|
|
|
|
|
192 Chapter 3 Solve problems | ENWW |