Bosch Appliances VG5 800 SERIES specification

32 en Installing the Pendant Arm Wall, Corner, and Mast (Pole) Mounts	AutoDome 800 Series HD PTZ Camera

CAUTION!

If you feel any resistance when rotating the dome housing or when engaging the connector, stop immediately and start over.

4.Hold the Pendant housing in position while tightening the two (2) 5-mm Allen head mounting screws on top of the housing to 10-12N-m(90-105in.-lbs).

CAUTION!

You must tighten the two mounting screws to a minimum torque of 10-12 N-m (90-105 in.-lbs) to ensure a proper seal between the arm and the housing.

F.01U.273.797 5.0 2012.08

Installation Manual

Bosch Security Systems, Inc.

Image 32

Bosch Appliances VG5 800 SERIES installation manual

Contents

AutoDome 800 Series HD PTZ Camera Page Table of Contents Configuring the AutoDome 800 Series Alarms and Relay ConnectionsUsing the AutoDome 800 Series Bubble Handling and Cleaning 113 Bvip Firmware Updates 115 Keyboard Commands by Number 116 Index 117 1Safety Important Safety Instructions En Safety AutoDome 800 Series HD PTZ Camera Coax grounding Safety PrecautionsImportant Notices En Safety AutoDome 800 Series HD PTZ Camera Selv Informations FCC ET Ices commercial applications Trademarks DisclaimerCopyright Customer Support and Service Installing the Pendant Arm Wall, Corner, and Mast Parts ListPole Mounts Unpacking Tools Required Pre-installation ChecklistDescription Mount Power Supply Box Route Wires and Attach Connectors Pendant Arm Power Supply Box Pin Alarm Output Flying Lead Pin Alarm Input Flying Lead Alarm and relay connectors 1Power Supply Box Connections Transformer 115/230VAC Models Route Power through Intermediate Power Supply Box Connector Pin P107 P101 6Attach Pendant Arm to Power Supply Box VG4-PA0 Power Supply Box 7Make Connections in Power Supply Box Pendant Arm to Power Box Hinge Alignment Control Control/Audio Coax Video VAC Power Ethernet VideoAlarm Inputs Alarm Outputs Relays Grounding Strap 11 Optional Fiber Optic Module For a Mast or pole installation Installing the VG4-A-ARMPLATEFor a Corner installation Route and Connect Wires to a Power Supply Box Attach the Pendant Arm to the Mounting Plate Cable 13 Pendant Arm Cables Ref. Description 14 Mounting Plate Inside DetailPage Attach Pendant to Arm and Tighten 15 Attach Pendant to ArmPage Installing Roof Parapet and Pipe Mounts VGA-ROOF-MOUNT Pre-installation Check List 3Mount Power Supply Box Wall Mount Power Supply with Optional Trim Skirt Align Cover Door Hinge to Power Box 1Attach Cover Door 4Route Wires and Attach Connectors VG4-A-PSU1 or VG4-A-PSU2 Power Supply Box Pipe Interface Board BNC 1Wiring the Power Supply Box 2Wiring the Fiber Optic Model HTR Dome 3Power Supply Box Connections Installing the VG4-A-9230 Roof Parapet Mount VGA-A-9230 Parapet Roof Mount Parapet Wall Mount Bracket and Roof Mount Plate End Cap with O-ring 6Installing the VG4-A-9543 Pipe Mount Pipe Mount Wire the Pipe Interface Board 10 Pipe Interface Board Connections Connecting Wires to the Pipe Interface Board Description Connector Wire Gauge Pin 11 Alarm and Relay Connector Plugs Attach Pendant to Pipe and Tighten 13 Pendant to Roof / Pipe Mount AttachmentPage Cable and Wire Standards PowerWire Distance Guide for Pendant Video and Control Cables Audio Line Input Specifications Wire SpecificationsAudio Cables Audio Connections AutoDome 800 Series HD PTZ CameraCable and Wire Standards en Alarms and Relay Connections Alarm InputsConnecting Alarms inputs 1 or Connecting a Normally Open Alarm Configuring an Open Collector Output AutoDome Programmed N.C System Requirements Using the AutoDome 800 SeriesOverview of Features Connecting the AutoDome 800 Series to the PC Configuring the AutoDome 800 Series Camera AutoDome 800 Series System Configuration Using the AutoDome 800 Series Web Server Changing the Network SettingsUsing the Configuration Manager Configuring Intelligent Tracking 1Intelligent Tracking Operation 6The Livepage Guidelines for Implementing Intelligent Tracking Maximum Number of Connections Protected AutoDome 800 SeriesProtected Network Image Selection System Log / Event Log Digital I/OTriggering Relay 1Entering a Keyboard Control Command To Enter a Keyboard Control CommandTo Set a Preset Shot Aux Control Tab To View a Preset Shot Using Intelligent TrackingUsing Special Functions Processor Load Saving SnapshotsRecording Video Sequences Page Recordings Controlling playbackPage Configuring the AutoDome 800 Series Basic Mode Device Access Basic Mode Date/Time Basic Mode Network Basic Mode Encoder Basic Mode Audio 6Basic Mode RecordingIsdn 2B Audio Basic Mode System Overview Advanced Mode GeneralPassword Identification Date/Time Date formatDevice date/Device time Device time zone Time stamping Display StampingCamera name stamping Advanced Mode Web Interface Appearance Livepage Functions Advanced Mode Camera Installer Menu Logging Installation Manual Video resolution Profile nameTarget data rate Maximum data rate Encoder Streams 264 BP+ bit-rate-limited MP SDProperty Preview White Balance Camera SettingsPrivacy Masks Shutter Mode Red GainBlue Gain Gain Control Lens Settings PTZ Settings Diagnostics Autopan Right LimitTilt Up Limit Tilt Limits Preposition and Tours SectorsTo define and edit an individual scene To define a preposition tour Miscellaneous LogsAudio Pixel Counter Advanced Mode Recording Storage Management Recording Profiles Not activeFormatting Storage Media Deactivating Storage Media Pre-alarm Time Post-alarm TimePost-alarm profile Alarm input / Motion alarm / Video loss alarm Retention Time Recording ScheduleRetention time Holidays Advanced Mode Alarm Alarm Connections Recording Status Video transmission Remote portVideo output Decoder VCA configuration 40 VCAAuto-connect VCA Profiles Alarm status Analysis typeMotion detector MOTION+ only Sensitivity MOTION+ only Trigger delay s Debounce time 1 s MOTION+ onlySelect Area MOTION+ only Tamper detection Scene too bright Scene too darkScene too noisy Reference Check Audio Alarm Audio alarmSignal Ranges Name Alarm E-Mail Alarm Task Editor Alarm Rules Advanced Mode Interfaces Alarm Inputs Operating ModeRelay Idle State Advanced Mode Network Network Access 49.1 IPv4Relay Name Trigger Relay Detailed Settings 49.2 IPv6 Interface mode ETH Enable DynDNSRCP+ port Telnet support Advanced Quality of Service MulticastUPnP TCP Port FTP Posting Encryption Advanced Mode Service Maintenance53 IPv4 Filter Page Licenses System OverviewUpload Download Bubble Handling and Cleaning CleaningCleaning the Bubble Interior Handling 2Cleaning the Bubble Exterior Do Not Upgrading the AutoDome 800 Series Bvip Firmware UpdatesBeginning the Firmware Update Process Keyboard Commands by Number To .5 Configuring Intelligent Symbols Index Jpeg Radius Vidos Page Bosch Security Systems, Inc