19-43
ATM Switch Router Software Configuration Guide
OL-7396-01
Chapter19 Configuring Circuit Emulation Services
Configuring T1/E1 Structured (n x 64) Circuit Emulation Services
Examples
The following example displays the circuit details for the softPVCs that you created in the previous
procedure (shown in Figure 19-7) using the show ces circuit command in privileged EXEC mode:
CESwitch# show ces circuit
Interface Circuit Circuit-Type X-interface X-vpi X-vci Status
CBR3/0/0 1 Active SoftVC ATM-P3/0/3 0 3088 UP
CBR3/0/0 2 Active SoftVC ATM-P3/0/3 0 2080 UP
CBR3/0/2 2 Passive SoftVC ATM-P3/0/3 0 32 UP
CBR3/0/3 1 Passive SoftVC ATM-P3/0/3 0 16 UP
The following example displays the CES-IWF addresses of the soft PVCs that you configur ed (shown in
Figure 19-7), using the show ces address command in privileged EXEC mode:
CESwitch# show ces address
CES-IWF ATM Address(es):
47.0091.8100.0000.00e0.4fac.b401.4000.0c81.8030.10 CBR3/0/0:1 vpi 0 vci 16
47.0091.8100.0000.00e0.4fac.b401.4000.0c81.8030.20 CBR3/0/0:2 vpi 0 vci 32
47.0091.8100.0000.00e0.4fac.b401.4000.0c81.8038.20 CBR3/0/2:2 vpi 0 vci 2080
47.0091.8100.0000.00e0.4fac.b401.4000.0c81.803c.10 CBR3/0/3:1 vpi 0 vci 3088
The following example displays the interface details for the new circuit 2 soft PVC that you set up on
port CBR 3/0/0 (shown in Figure 19-7), using the show ces circuit interface cbr command:
CESwitch# show ces circuit interface cbr 3/0/0 2
Circuit: Name CBR-PVC-AC, Circuit-state ADMIN_UP / oper-state UP
Interface CBR3/0/0, Circuit_id 2, Port-Type T1, Port-State UP
Port Clocking network-derived, aal1 Clocking Method CESIWF_AAL1_CLOCK_SYNC
Channel in use on this port: 24
Channels used by this circuit: 24
Cell-Rate: 172, Bit-Rate 64000
cas OFF, cell_header 0x200 (vci = 32)
Configured CDV 2000 usecs, Measured CDV unavailable
De-jitter: UnderFlow unavailable, OverFlow unavailable
ErrTolerance 8, idleCircuitdetect OFF, onHookIdleCode 0x0
state: VcActive, maxQueueDepth 81, startDequeueDepth 64
Partial Fill: 47, Structured Data Transfer 1
Active SoftVC
Src: atm addr 47.0091.8100.0000.00e0.4fac.b401.4000.0c81.8030.20 vpi 0, vci 32
Dst: atm addr 47.0091.8100.0000.00e0.4fac.b401.4000.0c81.8038.20
The following example displays the interface details for the new circuit 1 soft PVC that you configured
on port CBR3/0/2 (shown in Figure 19-7), using the show ces circuit interface cbr command:
CESwitch# show ces circuit interface cbr 3/0/2 2
Circuit: Name CBR-PVC-CA, Circuit-state ADMIN_UP / oper-state UP
Interface CBR3/0/2, Circuit_id 2, Port-Type T1, Port-State UP
Port Clocking network-derived, aal1 Clocking Method CESIWF_AAL1_CLOCK_SYNC
Channel in use on this port: 24
Command Purpose
show ces circuit Shows the configuration information for the
soft PVC.
show ces address Shows the CES address for the destination end
of the circuit.
show ces circuit interface cbr
card/subcard/port circuit-id
Shows the detailed interface configuration
information for the soft PVC.