Ethernet Link, Default IP Address | Extron electronic JMP 9600

Ethernet

Connection

This section provides a high level discussion of the Ethernet connections on the player and a primer on the subject of subnetting. Topics that are covered, include:

•Ethernet Link

•Subnetting — A Primer

Ethernet Link

The rear panel Ethernet connector on the switcher can be connected to an Ethernet LAN or WAN (see item G and “LAN Ports” in the “Installation” section).

Default IP Address

To access the media player via the LAN port, you need the IP address of the player. If the local system administrators have not changed the value, the factory-specified default IP addresses are as follows:

LAN 1: 192.168.254.254

LAN 2: 192.168.254.253

Ping can also be used to test the Ethernet link to the media player.

JMP 9600 Media Player • Ethernet Connection

105

Image 111

Extron electronic JMP 9600 manual Ethernet Link, Default IP Address, LAN 1 LAN 2

Contents

JMP Vorsicht AvertissementAchtung Precaucion FCC Class a Notice Conventions Used in this Guide Contents Mounting and Maintenance About the JMP About this Guide Typical JMP 9600 Application Features Digital video outputs HD-SDI or DVI-I2-channel output modes TByte of internal media storage Redundant Power Supply Backs Up Primary JMP 9600 Media Player Introduction Mounting the Media Player Connections and Features Pin Signal Video and Audio OutputsChannels of audio Lock Input and Output connectors LTC Linear Time Code Input and Output connectorsSync Both ports LAN PortsCabling LAN RJ-45 connector wiring Remote Control Port Digital Inputs and Relays Dual Redundant AC Power Input connectors Power Definitions Operation Status LEDs Front Panel Controls and Indicators Transport Buttons LCD and Menu ControlsEncoder knob Power-on Sequence Menu System OverviewMenu System Flow Channel Status Menu Channel status menus Select a Playlist Screen and Select a Clip Folder Screen Playlist and Clip fields Video selection Frame selectionShuttle selection Settings menu Loop selectionMute selection Audio Submenu Audio submenu Autostart submenu Autostart Submenu Flowchart Date and Time Submenu Date and Time submenu LCD submenu Apply new settings? Prompt Networking Submenu Networking submenu LAN Network Interface Network parameters JMP 9600 Media Player Operation Ping function Player submenu Serial Ports submenu Reboot submenu System Information Screen System Info selection Video Submenu Video submenu Mode Selection Are case sensitive Lock menu Help menu System Status menuLicense Keys menu About Screen About menu Play a Presentation Html Operation Options Connections LAN Settings, uncheck the Use a proxy Player Control Opening the Embedded Html Pages Real time status display Channel 1 and 2 Control and Status Windows Transport Controls Transport controls Loading a Clip or Playlist Loading a Clip or Playlist into a Player Channel Setting the clip or playlist to autoplay and view clip info Creating a New Playlist Playlist Editor Editing the Contents of a Playlist Removing Clips from a Playlist Remove a clip file from a playlist Play at and Stop at check boxes Editing the Properties of a Playlist Audio Setup Dialog Box Setup Functions Network Setup Dialog Boxes Autoplay Setup Dialog Box Eth1 = LAN port Network Ethernet setup dialog boxesNetwork Gateway setup dialog box Eth0 = LAN port Player Info Setup Dialog Box License Management Setup Dialog Box Serial Port Setup Dialog Box Submenu Serial Port Setup Dialog Box Video mode setup dialog box Video Setup Dialog Boxes Video analog setup dialog box Video HD-SDI setup boxES Genlock and ES MS9200 Genlock About Setup Dialog Box About Setup Dialog Box Remote Port Control Ports Opening the embedded Html Msvpp Default IP Addresses Host-to-Player Instructions TipsExtron products. Read this section Carefully Symbol Definitions Using the Command and Response Table X4# Media management Command Msvpp Command Response Additional description Command/response table for Msvpp commands Add a clip on rafting to the end of a playlist on river KEY Playback commands Canyon documentary playlist Playlist properties Timecode commands Loop commandsVideo mode Color wash Colorspace Sync HD-SDI VPI enableHD-SDI mode Audio delay Audio volume Audio muteLicense keys Ethernet configuration Serial port Remote 1 configuration SetDHCPX3@ Gateway Set Dhcp on Digital inputs and relays commands Reboot Time of dayDevice parameters Information requests Parameter Value Voltageps15vdc5.19vdc Voltageps25vdc5.17vdc GetVoltage X4! = Memory capacity or availablility Starting the FileZilla FTP Utility Data Transfer and Firmware Upgrade FTP Utility Local and Remote Sites Loading Media Files Loading Media Folders to the Media Player Deleting Files from the Media Player Deleting Folders and Individual Files from the Media Player Loading and Updating firmware Location of Firmware Upgrade Files Downloading Firmware Upgrade Files Loading a Firmware File Synchronization Sample Connections for System Synchronization Connections for Synchronized Multi-player Operation Comparison of the Effects of Timing References Applied Results of LTC and genlock timing references Esgen vs. traditional Genlock Esgen Genlock attibutesTraditional Genlock attributes Applicable Msvpp commands LTC commandsGenlock commands Configuring LTC for Synchronized Multi-player Operation Control Example Single file using separate controlCommand to Master Player Command to Slave Player Function Configuring a player as an LTC master Generate an LTC Set an LTC Receiver, Pre-Roll, and Post-Roll Configuring a player as an LTC receiver slave Select a Genlock Mode Configuring Genlock for Synchronized Multi-player Operation High Frame Rate Using Digital Inputs and Relays Optically-isolated Digital Inputs Digital Input Connection Using the Power Port Digital outputs commands Applicable Msvpp CommandsCommand Function Digital inputs commands Encoding Guidelines Reels Encoding and Packaging OverviewVideo track files Audio track files Supported Video Formats Composition playlistPacking list and asset map JPEG-2000 Restrictions UL guidelines Ventilation GuidelinesTabletop Use Rack Mounting Rack Mounting the Media Player Mounting instructions Cleaning the Air Filters Replacing Fuses Changing the Fuses Battery Precautions Troubleshooting a High Temperature Default IP Address Ethernet LinkLAN 1 LAN 2 Pinging to Determine the web IP Address Pinging to Determine the IP Address Ping with New Address Connecting as a Telnet Client Telnet TipsOpen IP Addresses and Octets Subnetting a PrimerGateways Local and Remote Devices Masked octets are not compared indicated by X in figure Subnet Masks and OctetsDetermining Whether Devices are on the Same Subnet Unmasked octets are compared indicated by ? in figure Video output SpecificationsContent/file format Video processing Audio processing Player syncTime code Sync- analog video outputs General Digital I/O control Included Parts Optional Accessories and Replacement FiltersPart Numbers JMP 9600 Part Numbers Cables Cable assembliesBulk cable and termination tools Europe USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Asia Middle East