Channel status menus | Extron electronic JMP 9600 specs

Channel status menus

NOTES: • Channel 2 Status is displayed in the main menu (figure 10) and available for

selection only in 2-channel output mode and 2-channel locked output mode,

both of which can be selected in the Settings > Video submenu.

• The Channel 1 Status and Channel 2 Status are identical, except where noted.

Figure 11 shows an overview of the Channel Status screen and the available settings.

Figure 11. Channel Status Menu

The LCD shows the current state of the channel 1, including the loaded clip and playlist (if applicable) and whether the presentation is playing, paused or stopped. The screen also shows two counters and a static display that display the time of specific functions of the time as hour:min:sec:frame:

Tc (Timecode) — The Timecode counter shows the current point in time within the loaded program. The Timecode counter includes the pre-roll, roll, and post-roll periods.

Lock indicator () — The lock indicator, when displayed, indicates the video that is playing is synchronized with an external genlock signal.

Fr (Frame) — The Frame counter shows the current point in time within the currently loaded playlist or clip; the roll period only.

Dur (Duration) — The Duration display shows the entire run-time of the currently loaded playlist or clip. This is a static display only.

NOTE: The frame field of the Tc and Fr counters is not updated during playback; only

the hour:min:sec fields are active. The Time count and Frame counters show the frame number when paused, in Frame mode, or in shuttle mode.

JMP 9600 Media Player • Operation

17

Image 23

Extron electronic JMP 9600 manual Channel status menus, Channel Status Menu

Contents

JMP Vorsicht AvertissementAchtung Precaucion FCC Class a Notice Conventions Used in this Guide Contents Mounting and Maintenance About the JMP About this Guide Typical JMP 9600 Application 2-channel output modes FeaturesDigital video outputs HD-SDI or DVI-I TByte of internal media storage Redundant Power Supply Backs Up Primary JMP 9600 Media Player Introduction Mounting the Media Player Connections and Features Channels of audio Pin SignalVideo and Audio Outputs Sync Lock Input and Output connectorsLTC Linear Time Code Input and Output connectors Both ports LAN PortsCabling LAN RJ-45 connector wiring Remote Control Port Digital Inputs and Relays Dual Redundant AC Power Input connectors Power Definitions Operation Status LEDs Front Panel Controls and Indicators Encoder knob Transport ButtonsLCD and Menu Controls Menu System Flow Power-on SequenceMenu System Overview Channel Status Menu Channel status menus Select a Playlist Screen and Select a Clip Folder Screen Playlist and Clip fields Shuttle selection Video selectionFrame selection Mute selection Settings menuLoop selection Audio Submenu Audio submenu Autostart submenu Autostart Submenu Flowchart Date and Time Submenu Date and Time submenu LCD submenu Apply new settings? Prompt Networking Submenu Networking submenu LAN Network Interface Network parameters JMP 9600 Media Player Operation Ping function Player submenu Serial Ports submenu Reboot submenu System Information Screen System Info selection Video Submenu Video submenu Mode Selection Are case sensitive Lock menu License Keys menu Help menuSystem Status menu About Screen About menu Play a Presentation Html Operation Options Connections LAN Settings, uncheck the Use a proxy Player Control Opening the Embedded Html Pages Real time status display Channel 1 and 2 Control and Status Windows Transport Controls Transport controls Loading a Clip or Playlist Loading a Clip or Playlist into a Player Channel Setting the clip or playlist to autoplay and view clip info Creating a New Playlist Playlist Editor Editing the Contents of a Playlist Removing Clips from a Playlist Remove a clip file from a playlist Play at and Stop at check boxes Editing the Properties of a Playlist Audio Setup Dialog Box Setup Functions Network Setup Dialog Boxes Autoplay Setup Dialog Box Eth1 = LAN port Network Ethernet setup dialog boxesNetwork Gateway setup dialog box Eth0 = LAN port Player Info Setup Dialog Box License Management Setup Dialog Box Serial Port Setup Dialog Box Submenu Serial Port Setup Dialog Box Video mode setup dialog box Video Setup Dialog Boxes ES Genlock and ES MS9200 Genlock Video analog setup dialog boxVideo HD-SDI setup box About Setup Dialog Box About Setup Dialog Box Remote Port Control Ports Opening the embedded Html Msvpp Default IP Addresses Extron products. Read this section Carefully Host-to-Player InstructionsTips Symbol Definitions Using the Command and Response Table X4# Media management Command Msvpp Command Response Additional description Command/response table for Msvpp commands Add a clip on rafting to the end of a playlist on river KEY Playback commands Canyon documentary playlist Playlist properties Video mode Timecode commandsLoop commands Color wash Colorspace Sync HD-SDI VPI enableHD-SDI mode Audio delay License keys Audio volumeAudio mute Ethernet configuration Serial port Remote 1 configuration SetDHCPX3@ Gateway Set Dhcp on Digital inputs and relays commands Device parameters RebootTime of day Information requests Parameter Value Voltageps15vdc5.19vdc Voltageps25vdc5.17vdc GetVoltage X4! = Memory capacity or availablility Starting the FileZilla FTP Utility Data Transfer and Firmware Upgrade FTP Utility Local and Remote Sites Loading Media Files Loading Media Folders to the Media Player Deleting Files from the Media Player Deleting Folders and Individual Files from the Media Player Loading and Updating firmware Location of Firmware Upgrade Files Downloading Firmware Upgrade Files Loading a Firmware File Synchronization Sample Connections for System Synchronization Connections for Synchronized Multi-player Operation Comparison of the Effects of Timing References Applied Results of LTC and genlock timing references Traditional Genlock attributes Esgen vs. traditional GenlockEsgen Genlock attibutes Genlock commands Applicable Msvpp commandsLTC commands Command to Master Player Command to Slave Player Function Configuring LTC for Synchronized Multi-player OperationControl Example Single file using separate control Configuring a player as an LTC master Generate an LTC Set an LTC Receiver, Pre-Roll, and Post-Roll Configuring a player as an LTC receiver slave Select a Genlock Mode Configuring Genlock for Synchronized Multi-player Operation High Frame Rate Using Digital Inputs and Relays Optically-isolated Digital Inputs Digital Input Connection Using the Power Port Digital outputs commands Applicable Msvpp CommandsCommand Function Digital inputs commands Encoding Guidelines Reels Encoding and Packaging OverviewVideo track files Audio track files Packing list and asset map Supported Video FormatsComposition playlist JPEG-2000 Restrictions UL guidelines Ventilation GuidelinesTabletop Use Rack Mounting Rack Mounting the Media Player Mounting instructions Cleaning the Air Filters Replacing Fuses Changing the Fuses Battery Precautions Troubleshooting a High Temperature LAN 1 LAN 2 Default IP AddressEthernet Link Pinging to Determine the web IP Address Pinging to Determine the IP Address Ping with New Address Open Connecting as a Telnet ClientTelnet Tips IP Addresses and Octets Subnetting a PrimerGateways Local and Remote Devices Masked octets are not compared indicated by X in figure Subnet Masks and OctetsDetermining Whether Devices are on the Same Subnet Unmasked octets are compared indicated by ? in figure Video output SpecificationsContent/file format Video processing Audio processing Player syncTime code Sync- analog video outputs General Digital I/O control Included Parts Optional Accessories and Replacement FiltersPart Numbers JMP 9600 Part Numbers Bulk cable and termination tools CablesCable assemblies Europe USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Asia Middle East