Power | Extron electronic JMP 9600 specs

Power

NOTE: Although the unit performs reliably while running on a single AC power supply, doing so defeats the dual-redundant power supply feature.

LDual Redundant AC Power Input connectors —

Connect a standard IEC power cord between one rear panel AC Power Input connector and a 100 to 240 VAC, 50-60 Hz

power source.

Connect a second IEC power cord between the remaining AC Power Input connector and either an uninterruptible power source or a power source that is completely independent from the primary power source.

WARNING: Physically disconnect both power cables from the player before opening the case for servicing.

MDual Redundant AC Power Input switches — Toggle both AC Power Input switches to the on ( ) position.

JMP 9600 Media Player • Installation

12

Image 18

Extron electronic JMP 9600 manual Dual Redundant AC Power Input connectors

Contents

JMP Precaucion AvertissementAchtung Vorsicht FCC Class a Notice Conventions Used in this Guide Contents Mounting and Maintenance About this Guide About the JMP Typical JMP 9600 Application Features Digital video outputs HD-SDI or DVI-I2-channel output modes Redundant Power Supply Backs Up Primary TByte of internal media storage JMP 9600 Media Player Introduction Connections and Features Mounting the Media Player Pin Signal Video and Audio OutputsChannels of audio Lock Input and Output connectors LTC Linear Time Code Input and Output connectorsSync LAN LAN PortsCabling Both ports Remote Control Port RJ-45 connector wiring Digital Inputs and Relays Power Dual Redundant AC Power Input connectors Operation Definitions Front Panel Controls and Indicators Status LEDs Transport Buttons LCD and Menu ControlsEncoder knob Power-on Sequence Menu System OverviewMenu System Flow Channel status menus Channel Status Menu Playlist and Clip fields Select a Playlist Screen and Select a Clip Folder Screen Video selection Frame selectionShuttle selection Settings menu Loop selectionMute selection Audio submenu Audio Submenu Autostart Submenu Flowchart Autostart submenu Date and Time submenu Date and Time Submenu Apply new settings? Prompt LCD submenu Networking submenu Networking Submenu Network parameters LAN Network Interface JMP 9600 Media Player Operation Player submenu Ping function Reboot submenu Serial Ports submenu System Info selection System Information Screen Video submenu Video Submenu Mode Selection Lock menu Are case sensitive Help menu System Status menuLicense Keys menu About menu About Screen Play a Presentation Options Connections LAN Settings, uncheck the Use a proxy Html Operation Opening the Embedded Html Pages Player Control Channel 1 and 2 Control and Status Windows Real time status display Transport controls Transport Controls Loading a Clip or Playlist into a Player Channel Loading a Clip or Playlist Setting the clip or playlist to autoplay and view clip info Playlist Editor Creating a New Playlist Editing the Contents of a Playlist Remove a clip file from a playlist Removing Clips from a Playlist Editing the Properties of a Playlist Play at and Stop at check boxes Setup Functions Audio Setup Dialog Box Autoplay Setup Dialog Box Network Setup Dialog Boxes Eth0 = LAN port Network Ethernet setup dialog boxesNetwork Gateway setup dialog box Eth1 = LAN port License Management Setup Dialog Box Player Info Setup Dialog Box Serial Port Setup Dialog Box Serial Port Setup Dialog Box Submenu Video Setup Dialog Boxes Video mode setup dialog box Video analog setup dialog box Video HD-SDI setup boxES Genlock and ES MS9200 Genlock About Setup Dialog Box About Setup Dialog Box Control Ports Remote Port Default IP Addresses Opening the embedded Html Msvpp Host-to-Player Instructions TipsExtron products. Read this section Carefully Using the Command and Response Table Symbol Definitions X4# Command Msvpp Command Response Additional description Media management Command/response table for Msvpp commands Add a clip on rafting to the end of a playlist on river Playback commands KEY Playlist properties Canyon documentary playlist Timecode commands Loop commandsVideo mode Colorspace Color wash Audio delay HD-SDI VPI enableHD-SDI mode Sync Audio volume Audio muteLicense keys Serial port Remote 1 configuration Ethernet configuration Digital inputs and relays commands SetDHCPX3@ Gateway Set Dhcp on Reboot Time of dayDevice parameters Information requests Parameter Value Voltageps15vdc5.19vdc Voltageps25vdc5.17vdc GetVoltage X4! = Memory capacity or availablility Data Transfer and Firmware Upgrade Starting the FileZilla FTP Utility FTP Utility Local and Remote Sites Loading Media Folders to the Media Player Loading Media Files Deleting Folders and Individual Files from the Media Player Deleting Files from the Media Player Location of Firmware Upgrade Files Loading and Updating firmware Downloading Firmware Upgrade Files Loading a Firmware File Synchronization Connections for Synchronized Multi-player Operation Sample Connections for System Synchronization Results of LTC and genlock timing references Comparison of the Effects of Timing References Applied Esgen vs. traditional Genlock Esgen Genlock attibutesTraditional Genlock attributes Applicable Msvpp commands LTC commandsGenlock commands Configuring LTC for Synchronized Multi-player Operation Control Example Single file using separate controlCommand to Master Player Command to Slave Player Function Configuring a player as an LTC master Generate an LTC Configuring a player as an LTC receiver slave Set an LTC Receiver, Pre-Roll, and Post-Roll Configuring Genlock for Synchronized Multi-player Operation Select a Genlock Mode Using Digital Inputs and Relays High Frame Rate Digital Input Connection Using the Power Port Optically-isolated Digital Inputs Digital inputs commands Applicable Msvpp CommandsCommand Function Digital outputs commands Encoding Guidelines Audio track files Encoding and Packaging OverviewVideo track files Reels Supported Video Formats Composition playlistPacking list and asset map JPEG-2000 Restrictions Rack Mounting Ventilation GuidelinesTabletop Use UL guidelines Mounting instructions Rack Mounting the Media Player Cleaning the Air Filters Changing the Fuses Replacing Fuses Troubleshooting a High Temperature Battery Precautions Default IP Address Ethernet LinkLAN 1 LAN 2 Pinging to Determine the IP Address Pinging to Determine the web IP Address Ping with New Address Connecting as a Telnet Client Telnet TipsOpen Local and Remote Devices Subnetting a PrimerGateways IP Addresses and Octets Unmasked octets are compared indicated by ? in figure Subnet Masks and OctetsDetermining Whether Devices are on the Same Subnet Masked octets are not compared indicated by X in figure Video processing SpecificationsContent/file format Video output Sync- analog video outputs Player syncTime code Audio processing Digital I/O control General JMP 9600 Part Numbers Optional Accessories and Replacement FiltersPart Numbers Included Parts Cables Cable assembliesBulk cable and termination tools Asia Middle East USA, Canada, South America Japan Central AmericaEurope, Africa, and the Middle China East Europe