Extron electronic JMP 9600 manual X4#

X2!

X2@

=	HD-SDI enable state	0 = not enabled, 1 = enabled
=	HD-SDI mode	“single”, “dual_422_12”, “dual_444_10“, or “dual_444_12“ or
		“dual_422_hfr“

NOTES: • The “dual_422_hfr” high frame rate is a licensed option of the JMP 9600 2K model.

• The high frame rate supports resolutions of up to 1920x1080 and 2048x1080 at 48, 50 and 60 Hz. High frame rate uses the dual HD-SDI connection mode per SMPTE 372M. The player must be set for 2-channel-locked mode and only content specifically encoded for the high frame rate mode plays back correctly.

X2# X2$

=	Delay	± up to 500 milliseconds
=	Volume	0 (no attenuation, full volume) through –144 (full attenuation, audio
		effectively muted)

X2%

X2^

X2&

=	License key	32 alphanumeric digits
=	License	Installed license (such as “V2HD“ or “V22K“)
= Serial port baud rate		300, 600, 1200, 1800, 2400, 4800, 9600, 19200, 38400, 57600, or
		115200

X2*

X2(

X3)

X3!

X3@

X3# X3$ X3% X3^ X3& X3*

=	Parity		“none”, “even”, or “odd”
=	Data bits		7 or 8
=	Stop bits		1 or 2
=	Serial port mode		“controlMSVPP“, “disabled“, or “passthrough”
=	Ethernet port		“Eth0” or “Eth1” (for LAN port 1) or “Eth2” (for LAN port 2)
=	IP address, Netmask, gateway address		###.###.###.###
=	DHCP on/off status		“On“ or “Off”
=	Hardware (MAC) address		##:##:##:##:##:##
=	Digital Input port or Relay output port		1, 2, 3, or 4
=	Level		“+“ = high level, logic 1; “–” = low Level, logic 0
=	Date	In the format: MM/DD/YYYY where: MM = month: 01 (Jan) through 12 (Dec)
			DD = day: 01 through 31
			YYYY = year: 1970 through 2037

X3(	=	Time	In the format: HH:MM:SS where: HH = hour: 00 through 23
			MM = minutes: 00 through 59
			SS = seconds: 00 through 59
X4)	=	Identifier	Location or name

NOTE: If there are spaces (•) In the identifier (such as Theater 1), the entire name must be enclosed in double quotation marks in the set

command (such as “Theater 1”). Quotes are not required for a single word identifer (such as Theater). The identifier is always in quotes in the response.

X4!	= Memory capacity or availablility		In 1024-byte blocks
X4@	= Video mode / channel availability		1 (1-channel mode) or 2 (2-channel mode or 2-channel locked mode)
X4#	= Horizontal or vertical resolution		Horizontal: 1280, 1920, or 2048		Vertical: 780 or 1080
X4$	=	Scan type	i (interlaced) or p (progressive)
X4%	=	Frame rate	23.98, 24, 24, 29.97, 30, 48, 50, 59.94, or 60
X4^	=	Player state	“playing“, “paused”, or “stopped”
X4&	=	Frame count	Number of frames (total or current position)
X4*	=	Percentage	Current position in a playing clip expressed as a percentage
X4(	=	Temperature	nn.nn °C
X5)	=	Voltage sensor	“ps1•5vdc“	“ps2•5vdc“
			“ps1•3.3vdc“	“ps2•3.3vdc“
			“ps1•12vdc“	“ps2•12vdc“
			“ps1•–12vdc“	“ps2•–12vdc“

NOTES: • The sensor name must be enclosed in double quotation marks as shown.

• Positive voltage sensor names must not include the positive sign (+); negative voltage sensor names must include the negative sign (–).

X5!

X5@

X5#

=	Voltage	±n.nn (3.3 vdc and 5 vdc sensors) or ±nn.nn (12 vdc sensors)
=	Version
=	Date

JMP 9600 Media Player • Programming Guide 59