Specifications, Content/file format | Extron electronic JMP 9600

Reference

Information

This section discusses the specifications, part numbers, and accessories for the

JMP 9600 Media Player. Topics that are covered include:

•Specifications

•Part Numbers

Specifications

Content/file format

File types		MXF-wrapped JPEG 2000 in DCP (Digital Cinema Package, unencrypted)
Video formats
JMP 9600 HD models		1280x720p5,6,7,8*, 1920x1080i2,3
		1	= at 24 Hz, 2 = at 25 Hz, 3 = at 29.97 Hz, 4 = at 30 Hz, 5 = at 48 Hz, 6 = at 50 Hz,
		7	= at 59.94 Hz, 8 = at 60 Hz (*at 4:2:2 only)
JMP 9600	2K models	1280x720p5,6,7,8 1920x1080i2,3,4, 1920x1080p1,2,3,4,5,6,7,8, 2048x10801,2,3,4,5,6,7,8
		1	= at 24 Hz, 2 = at 25 Hz, 3 = at 29.97 Hz, 4 = at 30 Hz, 5 = at 48 Hz, 6 = at 50 Hz,
		7	= at 59.94 Hz, 8 = at 60 Hz
Audio formats		16, 20, or 24 bits, 48 kHz broadcast WAV

NOTE: 1080p signals (1920 and 2048) at rates of 48 Hz and above are dual link HD-SDI only.

Video processing

Processing	8, 10, or 12 bits per color channel
Data rates	Playback at up to 250 Mbps (125 Mbps per video channel in 2 channel mode)
Standards	ISO/IEC 15444-1 JPEG 2000, 32x32 codeblock

Video output

Number/signal type	1 dual link HD-SDI in 4:4:4 or 2 single link HD-SDI in 4:2:2
	and
	2 DVI or RGBHV in 4:2:2
Connectors	2 female BNC
	2 female DVI-I
Nominal level	0.7 Vp-p for RGB
Minimum/maximum levels	0.0 V to 1.0 Vp-p for RGB
Impedance	75 ohms for RGB
Resolution	Follows input file format
Standards	Analog RGB, Y Pr Pb output: SMPTE 274M, SMPTE 296M
	DVI output: SMPTE 274M, SMPTE 296M
	HD-SDI output: SMPTE 292M (single link), SMPTE 372M (dual link)
Frame rate	Follows the file format.

JMP 9600 Media Player • Reference Information

111

Image 117

Extron electronic JMP 9600 manual Specifications, Content/file format, Video processing, Video output

Contents

JMP Achtung AvertissementPrecaucion Vorsicht FCC Class a Notice Conventions Used in this Guide Contents Mounting and Maintenance About the JMP About this Guide Typical JMP 9600 Application Features Digital video outputs HD-SDI or DVI-I2-channel output modes TByte of internal media storage Redundant Power Supply Backs Up Primary JMP 9600 Media Player Introduction Mounting the Media Player Connections and Features Pin Signal Video and Audio OutputsChannels of audio Lock Input and Output connectors LTC Linear Time Code Input and Output connectorsSync Cabling LAN PortsLAN Both ports RJ-45 connector wiring Remote Control Port Digital Inputs and Relays Dual Redundant AC Power Input connectors Power Definitions Operation Status LEDs Front Panel Controls and Indicators Transport Buttons LCD and Menu ControlsEncoder knob Power-on Sequence Menu System OverviewMenu System Flow Channel Status Menu Channel status menus Select a Playlist Screen and Select a Clip Folder Screen Playlist and Clip fields Video selection Frame selectionShuttle selection Settings menu Loop selectionMute selection Audio Submenu Audio submenu Autostart submenu Autostart Submenu Flowchart Date and Time Submenu Date and Time submenu LCD submenu Apply new settings? Prompt Networking Submenu Networking submenu LAN Network Interface Network parameters JMP 9600 Media Player Operation Ping function Player submenu Serial Ports submenu Reboot submenu System Information Screen System Info selection Video Submenu Video submenu Mode Selection Are case sensitive Lock menu Help menu System Status menuLicense Keys menu About Screen About menu Play a Presentation Html Operation Options Connections LAN Settings, uncheck the Use a proxy Player Control Opening the Embedded Html Pages Real time status display Channel 1 and 2 Control and Status Windows Transport Controls Transport controls Loading a Clip or Playlist Loading a Clip or Playlist into a Player Channel Setting the clip or playlist to autoplay and view clip info Creating a New Playlist Playlist Editor Editing the Contents of a Playlist Removing Clips from a Playlist Remove a clip file from a playlist Play at and Stop at check boxes Editing the Properties of a Playlist Audio Setup Dialog Box Setup Functions Network Setup Dialog Boxes Autoplay Setup Dialog Box Network Gateway setup dialog box Network Ethernet setup dialog boxesEth0 = LAN port Eth1 = LAN port Player Info Setup Dialog Box License Management Setup Dialog Box Serial Port Setup Dialog Box Submenu Serial Port Setup Dialog Box Video mode setup dialog box Video Setup Dialog Boxes Video analog setup dialog box Video HD-SDI setup boxES Genlock and ES MS9200 Genlock About Setup Dialog Box About Setup Dialog Box Remote Port Control Ports Opening the embedded Html Msvpp Default IP Addresses Host-to-Player Instructions TipsExtron products. Read this section Carefully Symbol Definitions Using the Command and Response Table X4# Media management Command Msvpp Command Response Additional description Command/response table for Msvpp commands Add a clip on rafting to the end of a playlist on river KEY Playback commands Canyon documentary playlist Playlist properties Timecode commands Loop commandsVideo mode Color wash Colorspace HD-SDI mode HD-SDI VPI enableAudio delay Sync Audio volume Audio muteLicense keys Ethernet configuration Serial port Remote 1 configuration SetDHCPX3@ Gateway Set Dhcp on Digital inputs and relays commands Reboot Time of dayDevice parameters Information requests Parameter Value Voltageps15vdc5.19vdc Voltageps25vdc5.17vdc GetVoltage X4! = Memory capacity or availablility Starting the FileZilla FTP Utility Data Transfer and Firmware Upgrade FTP Utility Local and Remote Sites Loading Media Files Loading Media Folders to the Media Player Deleting Files from the Media Player Deleting Folders and Individual Files from the Media Player Loading and Updating firmware Location of Firmware Upgrade Files Downloading Firmware Upgrade Files Loading a Firmware File Synchronization Sample Connections for System Synchronization Connections for Synchronized Multi-player Operation Comparison of the Effects of Timing References Applied Results of LTC and genlock timing references Esgen vs. traditional Genlock Esgen Genlock attibutesTraditional Genlock attributes Applicable Msvpp commands LTC commandsGenlock commands Configuring LTC for Synchronized Multi-player Operation Control Example Single file using separate controlCommand to Master Player Command to Slave Player Function Configuring a player as an LTC master Generate an LTC Set an LTC Receiver, Pre-Roll, and Post-Roll Configuring a player as an LTC receiver slave Select a Genlock Mode Configuring Genlock for Synchronized Multi-player Operation High Frame Rate Using Digital Inputs and Relays Optically-isolated Digital Inputs Digital Input Connection Using the Power Port Command Function Applicable Msvpp CommandsDigital inputs commands Digital outputs commands Encoding Guidelines Video track files Encoding and Packaging OverviewAudio track files Reels Supported Video Formats Composition playlistPacking list and asset map JPEG-2000 Restrictions Tabletop Use Ventilation GuidelinesRack Mounting UL guidelines Rack Mounting the Media Player Mounting instructions Cleaning the Air Filters Replacing Fuses Changing the Fuses Battery Precautions Troubleshooting a High Temperature Default IP Address Ethernet LinkLAN 1 LAN 2 Pinging to Determine the web IP Address Pinging to Determine the IP Address Ping with New Address Connecting as a Telnet Client Telnet TipsOpen Gateways Subnetting a PrimerLocal and Remote Devices IP Addresses and Octets Determining Whether Devices are on the Same Subnet Subnet Masks and OctetsUnmasked octets are compared indicated by ? in figure Masked octets are not compared indicated by X in figure Content/file format SpecificationsVideo processing Video output Time code Player syncSync- analog video outputs Audio processing General Digital I/O control Part Numbers Optional Accessories and Replacement FiltersJMP 9600 Part Numbers Included Parts Cables Cable assembliesBulk cable and termination tools Europe, Africa, and the Middle China East USA, Canada, South America Japan Central AmericaAsia Middle East Europe