About Setup Dialog Box | Extron electronic JMP 9600 manual

*

*

*

* These selections are available in 1 channel mode only.

HDSDI Mode — Select between the output modes shown at right. The green bar in the field indicates that your selection is being saved.

NOTES: • The Dual Link High Framerate,

available on the JMP 9600 2K model only, supports resolutions of up to 1920x1080 and

2048x1080 at 48, 50, and 60 Hz. The player must be set to 2-channel-locked

mode to select this rate. See “High Frame Rate” in the “Detailed System Interaction” section for more details on this mode.

• You can configure the media player signal combinations that are not defined

within the video payload identifier specification (SMPTE 352); for example single channel, dual link HD-SDI operation with 12-bit, 4:2:2 color sampling and the RGB color space. Some displays may not correctly display such an image or may require manual adjustment. The video payload identifier is updated correctly when the next valid SMPTE 352 format is selected.

Colorspace — Select between the Colorspace selections shown at right. The green bar in the field indicates that your selection is being saved.

VPI enable check box — Select (check) and deselect VPI as desired.

NOTE: The player ships with the dual-link HD-SDI VPI tag on by default. You may chose

to turn it off for backwards compatibility or legacy support.

About Setup Dialog Box

NOTE: The media player must run firmware version 2.06.07 or newer. If you have

an older version, update the firmware to ensure proper operation (see “Data

Transfer and Firmware Upgrade“ in the “Detailed System Interaction” section).

The About setup dialog box (see figure 58) displays the exact media player model, revision levels, and disk usage information. Firmware revision (to identify when upgrades are necessary) and disk usage (to determine if there is room for loading more clip files) are of particular interest.

Figure 58. About Setup Dialog Box

NOTE: The revision levels shown in figure 58 are examples only.

JMP 9600 Media Player • HTML Operation

54

Image 60

Extron electronic JMP 9600 manual About Setup Dialog Box

Contents

JMP Avertissement AchtungPrecaucion Vorsicht FCC Class a Notice Conventions Used in this Guide Contents Mounting and Maintenance About this Guide About the JMP Typical JMP 9600 Application Features Digital video outputs HD-SDI or DVI-I2-channel output modes Redundant Power Supply Backs Up Primary TByte of internal media storage JMP 9600 Media Player Introduction Connections and Features Mounting the Media Player Pin Signal Video and Audio OutputsChannels of audio Lock Input and Output connectors LTC Linear Time Code Input and Output connectorsSync LAN Ports CablingLAN Both ports Remote Control Port RJ-45 connector wiring Digital Inputs and Relays Power Dual Redundant AC Power Input connectors Operation Definitions Front Panel Controls and Indicators Status LEDs Transport Buttons LCD and Menu ControlsEncoder knob Power-on Sequence Menu System OverviewMenu System Flow Channel status menus Channel Status Menu Playlist and Clip fields Select a Playlist Screen and Select a Clip Folder Screen Video selection Frame selectionShuttle selection Settings menu Loop selectionMute selection Audio submenu Audio Submenu Autostart Submenu Flowchart Autostart submenu Date and Time submenu Date and Time Submenu Apply new settings? Prompt LCD submenu Networking submenu Networking Submenu Network parameters LAN Network Interface JMP 9600 Media Player Operation Player submenu Ping function Reboot submenu Serial Ports submenu System Info selection System Information Screen Video submenu Video Submenu Mode Selection Lock menu Are case sensitive Help menu System Status menuLicense Keys menu About menu About Screen Play a Presentation Options Connections LAN Settings, uncheck the Use a proxy Html Operation Opening the Embedded Html Pages Player Control Channel 1 and 2 Control and Status Windows Real time status display Transport controls Transport Controls Loading a Clip or Playlist into a Player Channel Loading a Clip or Playlist Setting the clip or playlist to autoplay and view clip info Playlist Editor Creating a New Playlist Editing the Contents of a Playlist Remove a clip file from a playlist Removing Clips from a Playlist Editing the Properties of a Playlist Play at and Stop at check boxes Setup Functions Audio Setup Dialog Box Autoplay Setup Dialog Box Network Setup Dialog Boxes Network Ethernet setup dialog boxes Network Gateway setup dialog boxEth0 = LAN port Eth1 = LAN port License Management Setup Dialog Box Player Info Setup Dialog Box Serial Port Setup Dialog Box Serial Port Setup Dialog Box Submenu Video Setup Dialog Boxes Video mode setup dialog box Video analog setup dialog box Video HD-SDI setup boxES Genlock and ES MS9200 Genlock About Setup Dialog Box About Setup Dialog Box Control Ports Remote Port Default IP Addresses Opening the embedded Html Msvpp Host-to-Player Instructions TipsExtron products. Read this section Carefully Using the Command and Response Table Symbol Definitions X4# Command Msvpp Command Response Additional description Media management Command/response table for Msvpp commands Add a clip on rafting to the end of a playlist on river Playback commands KEY Playlist properties Canyon documentary playlist Timecode commands Loop commandsVideo mode Colorspace Color wash HD-SDI VPI enable HD-SDI modeAudio delay Sync Audio volume Audio muteLicense keys Serial port Remote 1 configuration Ethernet configuration Digital inputs and relays commands SetDHCPX3@ Gateway Set Dhcp on Reboot Time of dayDevice parameters Information requests Parameter Value Voltageps15vdc5.19vdc Voltageps25vdc5.17vdc GetVoltage X4! = Memory capacity or availablility Data Transfer and Firmware Upgrade Starting the FileZilla FTP Utility FTP Utility Local and Remote Sites Loading Media Folders to the Media Player Loading Media Files Deleting Folders and Individual Files from the Media Player Deleting Files from the Media Player Location of Firmware Upgrade Files Loading and Updating firmware Downloading Firmware Upgrade Files Loading a Firmware File Synchronization Connections for Synchronized Multi-player Operation Sample Connections for System Synchronization Results of LTC and genlock timing references Comparison of the Effects of Timing References Applied Esgen vs. traditional Genlock Esgen Genlock attibutesTraditional Genlock attributes Applicable Msvpp commands LTC commandsGenlock commands Configuring LTC for Synchronized Multi-player Operation Control Example Single file using separate controlCommand to Master Player Command to Slave Player Function Configuring a player as an LTC master Generate an LTC Configuring a player as an LTC receiver slave Set an LTC Receiver, Pre-Roll, and Post-Roll Configuring Genlock for Synchronized Multi-player Operation Select a Genlock Mode Using Digital Inputs and Relays High Frame Rate Digital Input Connection Using the Power Port Optically-isolated Digital Inputs Applicable Msvpp Commands Command FunctionDigital inputs commands Digital outputs commands Encoding Guidelines Encoding and Packaging Overview Video track filesAudio track files Reels Supported Video Formats Composition playlistPacking list and asset map JPEG-2000 Restrictions Ventilation Guidelines Tabletop UseRack Mounting UL guidelines Mounting instructions Rack Mounting the Media Player Cleaning the Air Filters Changing the Fuses Replacing Fuses Troubleshooting a High Temperature Battery Precautions Default IP Address Ethernet LinkLAN 1 LAN 2 Pinging to Determine the IP Address Pinging to Determine the web IP Address Ping with New Address Connecting as a Telnet Client Telnet TipsOpen Subnetting a Primer GatewaysLocal and Remote Devices IP Addresses and Octets Subnet Masks and Octets Determining Whether Devices are on the Same SubnetUnmasked octets are compared indicated by ? in figure Masked octets are not compared indicated by X in figure Specifications Content/file formatVideo processing Video output Player sync Time codeSync- analog video outputs Audio processing Digital I/O control General Optional Accessories and Replacement Filters Part NumbersJMP 9600 Part Numbers Included Parts Cables Cable assembliesBulk cable and termination tools USA, Canada, South America Japan Central America Europe, Africa, and the Middle China EastAsia Middle East Europe