Kyocera 4035, 5035, 3035 manual Finished copies, Sided Open from Copy Left

Section 5 OTHER CONVENIENT FUNCTIONS

3Selecting between 1-sided or 2-sided copies

This procedure selects the type of finished copies to be made between 1-sided and 2-sided.

1With the content of the “Basic” tab displayed, touch the “1 sided/2 sided” key. The “1 sided/2 sided” screen will be

displayed.

Inch specifications

	Ready to Job build.					Set
	Place originals then press Start key.
Job Build - Step1						End
		11x81/2”	1 sided	1 sided copy		Insert
Select			Original	1 sided/		page
paper			type	2 sided	1 sided copy-Left
	Offset		AMS	Back Edge
					Finished page #:0
Finished			Reduce	Orig. set
			/Enlarge	direction
		Basic	Quality	Edit

3Touch the “Close” key. The touch panel will return to the screen in step 1.

4Selecting how to finished up the copy sets

If the optional Document Finisher is installed on your copier, this procedure lets you select whether to staple or hole punch the finished copy sets.

1With the content of the “Basic” tab displayed, touch the “Finished” key. The “Finished” screen will be displayed.

Inch specifications

	Ready to Job build.					Set
	Place originals then press Start key.
Job Build - Step1						End
		11x81/2”	1 sided	1 sided copy		Insert
Select			Original	1 sided/		page
paper			type	2 sided	1 sided copy-Left

Metric specifications

Ready to Job build.

Set original. Press Start key.

Job Build-Step 1

Set

End

Offset	AMS	Back Edge	Finished page #:0
Finished	Reduce	Orig. set
	/Enlarge	direction
Basic	Quality	Edit

	1-sided	1-sided Copy
Select	Original	1-sided/
paper	type	2-sided
Group	AMS	Back Edge
Finished	Reduce/	Orig. set
	Enlarge	direction

Insert blank page

1-sided Copy-Left Finished page #: 0

Metric specifications

Ready to Job build.

Set original. Press Start key.

Job Build-Step 1

Set

End

Basic Quality Edit

NOTE

	1-sided	1-sided Copy
Select	Original	1-sided/
paper	type	2-sided
Group	AMS	Back Edge
Finished	Reduce/	Orig. set
	Enlarge	direction

Insert blank page

1-sided Copy-Left Finished page #: 0

The setting in regard to making either 1-sided or 2-sided copies can only be made in the first step of the job build mode and will apply to all steps in the copy job.

2Touch the “1 sided” key or the “2 sided” key, as appropriate, and then select the binding direction you want for the

finished copies.

Follow the instructions on the right side of the touch panel and verify the direction in which the originals were set.

Inch specifications

Ready to Job build.			Set
Place originals then press Start key.
1 sided/ 2 sided copy		Back	Close
	Finished	Check direction
		Check direction of
		original top side.
1 sided	Open from
copy	left
2 sided	Open from
copy	right
	Open from	Rear	Left top
	top		corner

Basic Quality Edit

NOTE

The setting in regard to how the copy sets will be finished can only be made in the first step of the job build mode and will apply to all steps in the copy job.

Metric specifications

Ready to Job build.

Set original. Press Start key.

1-sided / 2-sided Copy

	Finished
1-sided	Left
Copy	binding
2-sided	Right
Copy	binding
	Top
	binding

Set

BackClose

Check direction Check direction of original.

Back Edge	Left top
	corner

IMPORTANT!

If the designation for the direction that the originals are set is not correct, copying may be accomplished incorrectly.

5-63