Manuals / Motorola / Computer Equipment / Computer Accessories

Motorola ATCA-717 manual Location of Critical Blade Temperature Spots Blade Top Side

Models: ATCA-717

1 156

Download 156 pages 224 b

Troubleshooting Install Block Diagram Error List Connecting to the Blade Default Configuration Location of Reset Key On−Board Hardware Accessories Via Setup Command and Status Register

Page 39

Requirements	Installation

Figure 1: Location of Critical Blade Temperature Spots (Blade Top Side)

PENT/ATCA−717

39

Page 38 Page 40

Image 39

Motorola ATCA-717 manual Location of Critical Blade Temperature Spots Blade Top Side

Page 38 Page 40

Related pages All Temperature page Fresh food temperature too warm for Hotpoint CTF~GC Controlling Temperature for Samsung RF23HCEDBSR/ML Indoor coil temperature abnormality detection for Mitsubishi Electronics PKH24FL Basse temperature for Samsung RL39TJCTS1/XES Oven Temperature Shows the oven temperature selected for Bosch Appliances BOSCH GAS FREE-STANDING CONVECTION RANGE Color temperature for Philips 180P2M/180P2G Heating Rate Temperature for Paragon WTNFII-10 Electronic Temperature Control for Electrolux EILFU21GS Temperature and Time for Cannon 10856G Temperature Control for Samsung LH40MECPLGC/EN How can I set up Dynamic DNS on my tp link router? Find out more

Contents

PENT/ATCA−717 Copyright Contents Bios Devices’ Features and Data Paths Maps and Registers Appendix a Troubleshooting Appendix B Battery Exchange Index Tables PENT/ATCA−717 Figures Battery Exchange Conventions Using This Guide Abbreviations FCC Revision History PENT/ATCA−717 PENT/ATCA−717 For further information refer to the following documents.a Other Sources of Information Smsc Installation Safety Notes Operation Switch Settings Battery EnvironmentPMC Modules PENT/ATCA−717 EMV Sicherheitshinweise Betrieb Schaltereinstellungen UmweltschutzPMC−Module Batterie Introduction About this Manual Organization of this ManualFeedback Introduction About this Manual Features Standard Compliances Ordering Information Product NomenclatureOrder Numbers Introduction Ordering Information Installation Action Plan Start installation Environmental Requirements Requirements Installation Requirements Location of Critical Blade Temperature Spots Blade Top Side Power Consumption PENT/ATCA−717 Location of On−board Switches Switch Settings Switch Settings Installation PENT/ATCA−717 PENT/ATCA−717 On−Board Hardware Accessories On−Board Hardware Accessories Installation Removal Procedure Installation Procedure Hard Disk Installing a Hard Disk Removing a Hard Disk CompactFlash Disk Location of CompactFlash Disk Connector CompactFlash Installation CMC Debug Module Rear Transition Modules Installation into Powered Shelves Blade Installation Wait until the blue LED is illuminated permanently Installation in Nonpowered Shelves Removal Procedure ACC/CABLE/PMC/RJ−45 Cable Accessory Kits Controls, Indicators, and Connectors LEDs Face Plate Meaning of these LEDs is described in the following table.a HDD Keys Location of Reset Key Connectors Their pinout is given below.a CompactFlash On−Board Connectors On−Board Connectors Controls, Indicators, and Connectors Diff. Pair PMC Sites 2 and 3 − Pn4 Connector Pinout Parallel ATA Connector Pinout of the connector is as follows.a Parallel ATA Connector Pinout Serial ATA Connector Location of Serial ATA Connector CMC Module Connector Location of CMC Connector AdvancedTCA Backplane Connectors PENT/ATCA−717 P10 Backplane Connector Pinout P20 Backplane Connector Pinout − Rows E to H P22 Backplane Connector Pinout − Rows E to H P30 Backplane Connector Pinout − Rows a to D P31 Backplane Connector Pinout − Rows a to D P32 Backplane Connector Pinout − Rows E to H Bios Introduction Bios Default Configuration Serial Console RedirectionRequirements Procedure Connecting to the Blade Bios Crisis Recovery Mode Main Menu Changing Configuration Settings Via Setup Selecting The Boot Device Via Boot Selection Menu Boot Menu Procedure Restoring Bios Default Settings Updating Bios Bios Messages Keyblade not working Check for correct keyblade Connection Nvram Cmos clock Replace battery and run Bios Post Codes Bios Bios Bios 100 101 102 Devices’ Features and Data Paths 104 PCI PCI−X LPC PMC I/O Block Diagram CPU Hub Interfaces Host BridgeHost Interface Memory Interface Interrupt Controller South Bridge Parallel ATA Interfaces Real−Time ClockWatchdog PCI−X Interface Serial RS232 Interfaces USB InterfacesPCI Interface Serial ATA Interfaces SMBus Interface Keyboard/Mouse Controller Super I/OSerial Interfaces Floppy Disk Interface Flash Devices Boot Flash LPC Device ID Control Devices’ Features and Data Paths Flash Devices Block Transfer Interfaces Ipmc Interface Port 80 Register Reset ControllerReset Types Clock Synchronization Extensions Reset Sources Interrupt Routing UnitMiscellaneous Glue Logic PMC Status Register Reset Mask and Source RegisterSerial Interface Flash Control Register Ipmi Structure Intelligent Platform Management Controller Sensors Ipmi Temperature Sensors 121 Atca IPMB0 Progress I2C Addresses Blade Clock Synchronization Interface 125 Blade Power Supply Structure Power Supply Module PCI Bridge P64H2 Routing Options Switching UnitFeatures Management Interface Switching Unit Devices’ Features and Data Paths PMC 1B 131 Maps and Registers Following table shows the blade′s main address map.a Memory Maps Maps and Registers Memory Maps Hardware Interrupts PCI Structure PCI Devices Fpga Registers Ethernet Switch Management Registers Ipmi Block Transfer Interface RegistersPort 80 Register Clock Divider Register Reset RegistersCommand and Status Register Data Registers Pwron Flash Control and Status Register LED Control Register Shut Down Register PMC Status Register SPI Interface Registers Clock Synchronization Interface Registers Reference Clock Source Register Dpll Input Select and Control Register Reference Clock Divider Registers Serial Prom Update Register Version RegisterReference Clock Pulse Width Register Access Control Register Troubleshooting Error List Battery Exchange Location of On−board Battery Battery Exchange Remove old battery Exchange Procedure Index Fpga Temperatures Critical hot spots Non−operating USB connectors

Top Page Image Contents