On−Board Hardware Accessories |
|
| Installation | |||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Figure 4: Location of PMC Slots
PMC slots 1 and 2 belong to one PCI segment and PMC slots 3 and 4 belong to another PCI segment. Within the same PCI segment, it is possible to install two PMC modules of different modes (PCI/PCI−X) and speeds (33/66/100 MHz). The PMC module with the overall lower performance (combination of speed and PCI mode) determines the speed and PCI mode of the second PMC module.aaa
Example:aA PMC module supporting PCI−X/66MHz is installed into PMC slot 1 and a PMC module supporting PCI/66MHz is installed into PMC slot 2. In this case both PMC modules are operated in PCI/66 MHz mode because the PMC module with the overall less performance is the one supporting PCI/66 MHz and consequently the second PMC module is operated in this mode as well.a
Before installing PMC modules, the following general safety notes must be observed.a
PENT/ATCA−717 | 47 |
