834 H.323 Options, Parameter Description Default | Samsung 7100

OfficeServ 7100 Call Server Programming Guide

[834] H.323 OPTIONS

This MMC provides various VoIP support options. The options set in this MMC apply sys- tem wide.

No	Parameter	Description	Default
00	GATEWAY CALL ID	Numeric identifier for system(up to 12 digits)	1234

01	H.323 FAST SETUP	Enables or disables the H.323 Fast Start call setup	ENABLE
		method.
02	CALLER ID TYPE	This option controls the calling party identification	ANI
		type. There are 3 possible selections:
		0 GWID: shows the gateway call ID.
		1 ANI: shows the calling station number
		2 IP: shows the calling H.323 gateway IP ad-
		dress.

06	TUNNELING	Enables or disables the need for additional chan-	ENABLE
		nels using H.245 signalling. Tunneling allows use
		of the H.245 signal channel with the Q.931 chan-
		nel.

07	DEFAULT DIL NO	This allows programming of the default direct-in-	500
		line number when digits are missing or incorrect on
		an inbound call.
11	CODEC AUTO NEGO	Enables or disables Auto CODEC Negotiation	ON
		when the MGI is used as an H.323 gateway.

14	SIGNAL PORT	Indicate the port number for H.323 signalling and	10000
		sets a range of numbers allowed by firewall
		equipment. The common and default IP path or
		port used is 10000.

17	SEND CLIP TABLE	Refers to SEND CLI NUMBER(MMC 323), which	1
		provides calling party identification when using the
		MGI as a H.323 gateway. This provides station ID
		of the calling station. A single-digit value corre-
		sponding with the desired table in MMC 323
		should be entered here. This is only used when
		MMC 405 value is null.
18	INCOMING MODE	This option selects how incoming calls are routed	FOLLOW
		when the MGI is used as a H.323 gateway.	DID TRANS
		0 FOLLOW TRUNK RING: Follows MMC 406
		1 FOLLOW DID TRANS: Follows MMC 714
		2 FOLLOW INCOM DGT: Follows MMC 724
19	ALLOW GW CHECK	When using a gatekeeper, this permits the H.323	DISABLE
		gateway to check for gatekeeper presence.
20	CLIR WITH NUMBER	When this option is enabled, the CLIP number is	DISABLE
		sent to the network even if the CLIP restriction flag
		is set.

21	USE OVERLAP DIAL	Enables use of overlap dialing.	ENBLOC

Samsung Business Communications

2-305

Image 349

Samsung 7100 manual 834 H.323 Options, Parameter Description Default

Contents

Programming Guide Copyright Trademarks Purpose Guide ContentsAudience Console Screen Output Conventions Revision History Reference GuidesFirst Edition This page is intentionally left blank Restriction SymbolsInstruction When changing the MMC 506, 807 Before using the Auto Record featureCompliance with the National Version Standards Table of Contents MMC Programming Overview of Programming Procedure 100 414 MPD/PRS Signal Assign Trunk SignalSystem Timers STATION-WIDE Timers 177 Enable Technician Program TAX Rate SetupCustomer Access MMC Number Card PRE-INSTALL Abbreviation List of Figures Overview of MMC Pro Gramming 24B LCD DCS Euro Phone DCS Euro Phones DS-5038S Phone 2 DS/ITP-5000 Series Phones DS/ITP-5014D/5021D Phone DS-5014S/5007S Phone Using large LCD Phones Station Level Programming list Station Level ProgrammingMMC No MMC Name Station Lock System Related MMC list Operator Level Programming Station Related MMC list Trunk Related MMC list Group Related MMC list Timer and Tone Related MMC list Tables, Codes, AA, Dect and VM MMC list MMC No MMC Name Tables, Codes, AA, Dect and VM MMC list Technician Level Programming list SYS. I/O ModeOptions MGI DSP Options Alarm Reporting Wlan ConfigurationSystem Alarm Assignments Maintenance Busy Assign ADD on Module Alphabetically arranged Programming list MMC Name MMC No BSI RF Carrier Confirm Outgoing Call Hardware Version Display Pickup Groups System SIO Mode VoIP Access Code MMC VoIP IP Table Phone Function Program List by Function VoIP Function Networking Function LCR Function Wlan Function12 VoIP Function Programming list MMC Program No Program Description Auto Attendant/Voice Mail Function Hotel Function Diagnosis FunctionPage MMC Programming ALL Stations Unlocked Station LockType Description Assign Station COS Assign COS Contents Change User Passcode Default passcodesALL Station Passcodes None Call ForwardType STATION-WIDE Timers System Timers ALL Phones Ring SET Answer ModeTo answer the C.O. call automatically Select all phones Dial 0, 1 or 2 to change ring mode Station Name Volume Up/Down keysDial Display shows Dial station number.e.g Program Buttons Station Speed Dial Assign Speed Block Station Speed Dial Station Speed Dial Name KEY Extender Key Feature Extender Copy KEY Programming When using the Right Soft buttonStation KEY Programming System KEY Programming Status Description Station Status Assign BOSS/SECRETARY Pickup GroupsAssign Station Group Assign Station to page Zone Date Display Mode DescriptionCountry Western Clock 12 Hour Display Lower Case Assign Date and Time Station ON/OFF Feature Default Description Not CONT.CID See Description Some Options Depend on CountryAuto ANS CO OFF Enblock 2LCD OFF Assign COS Contents Phone Ring Tone Phone VolumeFrequency Alarms are Notset Alarm Reminder ClockNotset Today Alarm and Message View Memo Number Phone Volume Dial volume type.e.g No Messages Selected SET Programmed Message Alarm and Message Alarm Reminder Clock Blank Message Edit Text Message Conference Group Allow Group Conference Number First Caller ID DisplayAllow Caller ID Assign Review Block Option Description Large LCD Options MMC 719 Idle Display English Phone LanguageLanguage None News Display Speed Executive State Answer ModeExec State Statein Related Items Show License Status Feature DescriptionInvalid SYSTEM-WIDE Timers DisableOpen Customer Programming Change Customer Passcode Passcode Change Customer Passcode Ring Plan Disa Alarm Alarm CLR Dect Regst Change Feature PasscodeWlan Regst Assign Disa Trunk Assign UA Device When setting the MMCCommon Bell Control Ringing Device Description Continuous Common Bell ControlAssign UA Device Unassigned Assign Loud Bell No BARGE-IN BARGE-IN TypeNo BARGE-IN With Tone Assign VM/AA Port When using the MMCNormal Port 1VMAA, 0NORMAL ICM Ring ICM RingCO Ring Data Ring Masternone Assign ADD-ON Module Customer ON/OFF PER Tenant Option Default Description VPN Enable OFF CancelICM EXT FWD OFF Did ERR Tone OFF SGR ALL OUT OFF CleanedChain FWD TRK Moniter OFF CO-CO TM ALL OFF Voip Realrbt OFFSmdr LOG OFF ALL Dial option number.e.g Station Group Door Ring Assignment ALL Ring Plans Disa Alarm Ringing Station Auto Print OFF Traffic Report Option Dial 0 for manual or 1 for automatic print Relay Type Voice Isdn Service Type Normal Station Extension Type Dial 0 5 to select station type Extension Type FAX Pair AA Group None Message no None Group Busy None WAKE-UP AnnouncementAA Group Message no Enter the AA group number Customer ON/OFF PER Station LCR Time Table LCR Digit Table Assign Station COS Enter the next ring plan class of service.e.g No Pickup Groups Assigned Pickup GroupsKEY Extender Assign BOSS/SECRETARY Dial YES ANS YES Assign EXTENSION/TRUNK USE Copy Station Usable Account Code Assign Forced Code HOT LINE/OFF Hook Selection Assign Trunk MOH Source Assign Background Music Source Tone Assign Station MOH Source Least Cost Routing COS LCR Class of ServiceLCR Route Table RCV YES SND YES Allow Caller IDRCV SND Confirm Tone Confirm Outgoing CallDisconnect Customer SET Relocation 48B 64B IDCS Allowed 12B 24B Relocate28D 18D IDCS 28D SLT Euro 6B Euro 12B Euro 24B 48B AOM 64B AOM STATION/TRUNK USE Group Copy Station Usable Dial YES Assign STATION/STATION USE Tone Distinctive RingingCadence Dial trunk or station number.e.g MMC Branch Group When using PRE FWD Busy option in MMC Preset Forward no AnswerINT EXT Dial call type 0, 1 or 2.e.g Empty Calling Party NumberBRI Options PRI Options Ringback Tone Message Customer ON/OFF PER Trunk Display show ALL Trunks CO Line Trunk LINE/PBX Line ALL Trunks Dtmf Trunk Dial TypeDtmf Type Dial Pulse Type ALL Trunks F-STN Trunk Toll ClassClass Description Enter day toll class.e.g., 2 for CLS-B Station Name Trunk Name Entering Numbers Trunk CO TEL Number Trunk Ring Assignment ALL Trunks Ring Default Operator GroupAssign Ring Plan Time Forced Trunk Release Assign Trunk MOH Source Follows Trunk Trunk Status Read Trunk LINE/PBX Line Customer ON/OFF PER TrunkTrunk Dial Type Trunk Toll Class ALL Trunks Normal Assign Disa Trunk Signalling condition type Assign Trunk SignalImmediate Start Nonenormal 414 MPD/PRS SignalPRS MPD MMC TRUNK-WIDE Timers ALL Trunks Report YES Report Trunk Abandon DataReport no Report YES CRC4 on 417 E1/PRI CRC4 Option Mode BRI and PRI Card Restart BRI Options Channel ANY YES Power Feed no Display shows first BRI channel Trunk CO TEL Number Calling Party NumberBRI & PRI Card Restart MSN Digit PRI Options PRI ModeNormal Same Connid Dial first PRI trunk number in PRI card.e.g CW YES OPT Accept MSN Digit ALL Ring Plans COS Trunk COS ALL TRK COS BRI S0 Mapping 423 S/T ModeTrunk BRI S0 Mapping Normal Trunk CID Trunks Trunk Gain Description Trunk Gain Control Assign TRUNK/TRUNK USE SET H-TRK Default Data Action Display ALL TRUNKS/ALL Dial Plans ALL Cost Rates Assigned Cost RateCosting Dial Plan Display trunk connection status Connection Status Display trunk status in conference Station Status Trunk TMC Gain 437 16TRK Gain Control Default Data Action SYSTEM-WIDE Counters Counter Default DescriptionSee Description Enter number from above list.e.g Timer Name Default Range Unit Description System Timers CO Confirm Time Display Delay TMCO-CO Disconnect Confirm Tone TM First Digit Time MCL Delay TimeHOK Flash MAX TM HOK Flash MIN TM MS LED on Time Power Down TimeOFF Hook Ring INT Ohva Answer Time When timers value is ‘0’ See Description Some Timers Depend on Country Display shows first timer value STATION-WIDE Timers Call Forward Description Range TRUNK-WIDE Timers Disa Answr Conn Delay 151 MAKE/BREAK 33 Make Pulses PER Second 10 PPS Pulse MAKE/BREAK RatioMAKE/BREAK Ratio Pulse PER Second Type Description Range Assign Date and Time Tone Cadence When changing the MMCUnit milliseconds Terrupt Start Time End Time Assign Ring Plan Time Ring Plan Start None END None Unit Cost PER MP 0200 PENCE, Call Cost Rate 100 Percent Call CostDisplay Description Unit Cost PER MP SLI Ring Cadence 160 Interrupt LED 1000MS-ON 1000MS-OFF MSG Waiting Lamp CadenceInterrupted No Holiday Assigned Follows Ring Plan Holiday Assignment Room Clean Time Hotel TimerCheck OUT Time Check in END TM Tone Source No YY Start END Daylight AssignmentAssign Date and Time Assign Operator Group Type 1 UCD Assign Station GroupType 2 UCD Groups Calls to a group Normal Group Dial next feature option and continue Station Group Name Trunk group Assign Trunk Group LCR Programming No Stations Assigned Assign Station to page Zone Assign External page Zone System 200 Entries Stations 1 Block Assigned Assign Speed Block Assign System Speed Dial Station Speed Dial Name UCD Options Ring Next Time Final DestinationUCD Recall Time WRAP-UP Time Alloutæfinal Auto LOG OUTAgent PIN no Group Busy Next Press Volume button to select UCD group or dial Phones 10 Bins Assign Review BlockSmdr Options Call LOG Block Allow Text Messaging Allow Group Conference ALL Stations ALL Trunks None STATION/TRUNK USE GroupAssign STATION/STATION USE Assign TRUNK/TRUNK USE MGI Group Display shows the first available option MGI User Copy COS Contents Assign COS Contents Flash YES Feature YESFOLLOW-ME YES Forward YES RNG Plan YES REM. Hold YESSecure YES SET Rloc Dial COS.e.g ALL Entries are SET to Toll Deny Table Toll Allowance Table Toll Deny Table Entries SET to Z Entries SET to Assign Wild Character ANS/RLS Assign System Speed Dial No Names System Speed Dial by Name Assign System Speed Dial Assign Forced Code Authorization Code Account Code Special Code Description Toll Pass CODE/SPECIAL Code Table Toll Restriction LCR Digit 0001 Digit LCR Digit 0005 Digit LCR Digit Table LCR Time Table LCR Route Table LCR Class of Service Digit String KEY LCR Modify Digit TableOption Description Max. No. of Digit Entries NOF DEL DGT Enter digits to be appended.e.g DGT Did Number and Name TranslationPRI Name Enter valid index numbere.g., 005 via dial keypad Enter call wait option via dial keypad Leave a Message On Vacation Gone Home Programmed Station Message Network Code UK LCR OptionPIN Code CCC Option LCR Modify Digit Table UCD Options UCD Agent ID MY Area Code Idle Display Copy KEY Programming Save Station KEY Programming Restore BOOTHHotel Feature BILLHotel FeatureStation KEY Programming Path Replacement Message CancelEasy Alarm SET to Isdn Supplementary Service Timer System AlarmsHeadset Mode Universal Answer Voice Mail Administration Enter selected station number.e.g Type of Phone Description System KEY ProgrammingBTN Sets EU 6B Sets See Default Data in MMC Type of Dial No Description Dial Numbering Plan MGI Dial no Virt EXT Dial noIP STN Dial no Wlan Dial no Choice None Chout NoneConf Conference Conp None Connected Name Display Credit None RTO None Ring Plan Time Override Selfid Self System ID Reject None Ohva Reject Ring Plan RSV See Description Feature Codes Depend on Country Dial option number to make selection.e.g Smdr Options Answer IncomingIntercom Call KEY MMC IN/OUT Dial the option number.e.g System Version Display CID Translation Table Station Pair When changing the COS MMC 749, Rate Calculation Table Costing Dial Plan Cost Rate ALL Cost Rates no Data Rate Calculation TableCurrency values£ or € Dial option number 0-4.e.g ALL Options are no VM Card Restart MBX Download ALL Stations YES ALL Groups no Assign Mailbox Auto Record Dial VM number via dial keypad 5000 Restart VM Halt Threshold 80% VM Alarm Assign Vmmoh When the first Built-In Voice Mail port is used for VmmohNot Used IN/OUT VM IN/OUT ALL Ring Plans DAY VM DAY/NIGHT CLI CLI RingingREJ Allow Caller ID No Entries Item Cost TableCode Description Enter valid code numbere.g., 02 via dial ALL Rates are % TAX Rate SetupTAX Rate Value Enter the tax rate or value via dial keypad ALL Rates are 100% Room Cost Rate Second LCR Option Description Default LCR Time LCR ClassLCR Route Number Plan Enable Technician Program Change Technician Passcode Default Passcode Customer Access MMC Number SVMi TX Level and Gain Action Display When a card is removed and a different type card is inserted Card PRE-INSTALL Are YOU SURE?NO Phone Volume Level Phone Volume Control 21D Depends on Phone Typeshown for 21D Proc Halt Processing Clear Memory Reset SystemFast Restart System Restart are YOU SURE?YES SET Country Code TAX Rate Setup Hotel TimerHotel Operation FAX Pair Clear Mcdb Customer Database CopyCopy to Sram Copy to Mcdb If you select YES, the display shows Program Download File Name Description MC File Control Press Volume button to confirm program type Assign Network Trunk Assign System Link IDAssign Network COS Ethernet Parameters Normal Assign Network Trunk BTN SET Virtual Extension TypeLarge SET BTN LCD Enter virtual extension number Assign Network COS Dial the class of service number.01-30 Network Dial Translation Enter YES/NO to assign Mailbox to remote Assign Networking Options Dial the option number Priority 1 C1-S0 Priority 2 C1-S1 Priority 3 Self Assign System Reference Clock LAN Printer Parameters Enter type of data to be printed Parameter Description Ethernet Parameters Ethernet Parameters CTI Server Addr Display shows the system IP address MGI Parameters IP Type Private IP only Version Card Reset no VoIP Access Code Options Voip IP TableSIP Options When changing IP Voip Access CodeVoIP IP Table TB00 ENTRY00 MMC 830 System IP Addr ALL Others Empty 834 H.323 Options Parameter Description Default Gateway Call ID Fast Setup Disable Fast Setup Enable MGI DSP Options TOS Field OutbandFAX Retry RTP CHK TM MGI Parameters 836 H.323 GK Options USE Multi E.164 GRQ SendLists GK Registered SIP Options Provisional Port Signal PortINV.NO Resp GEN.NO Timer 0NONE, 1UPDATE, 2REINVITE Server Registered GW ServiceSIP GW Domain 315 SIP User Private IP Addresses IP Phone Information Jitter BUF UpgradeMMC 841 ITP DSP Para Down = Phone Data Time Zone MGI User MGI GroupMGI DSP Options System IP Options System IP Options ITP DSP Para CTI Link OptionSYS Data ITP TX GAIN/HSET ITP TX GAIN/MIC CommandITP RX GAIN/SPKR ITP Vers Show License Status Wlan Parameters Parameter Description Defaultms When the cursor is on WLAN, press Volume button BWBS=BASIC WBS Range is 0-99900 ms.Default 6000 ms WIP Information Wlan IP/MAC List Wlan Configuration WIP Information Wlan IP/MAC List Wlan Configuration Enter WEP KEY values when the WBS WEP SER Only MMC Dtmfr DSP’S CID DSP’S R2MFC DSP’S Conf GROUP’S System Resource Display View Alarms Alarm ReportingClear Alarm BUF Print Alarm BUF Enter desired option Alarm Notification System Alarm AssignmentsCode Alarm Name Definition MJA MCP2 Error System Fault LCP/TASK Error LCP or Task Fault Code Alarm Name DefinitionDSP Error System DSP Fault Dtrk Error Isdn or E1 card Fault MGI Error MGI card Fault Minor Error Minor Fault with Alarm Buffer saving Minor Error Minor Fault without Alarm Buffer saving Maintenance Busy Alarm ReportingALL OFF ALL Idle Maintenance Busy Display shows busy functions No Diagnostic Time SET Diagnostic Time Nnnn Tech Programming LogsLAN Type Range Virtual Cabinet SET MMC 724 Number Plab MMC 822 VIR.EXT Type Only MMC Hardware Version DisplayMP Card System Options Auto Update Time System Speed Dial Assign Speed Dial Block Node Info Access NUMTEL Number MAX Count Initialize Port ACD AAAALG AME Dect DaslDhcp Dpim Ipdc IPCIPM IP-SCP PAT OPXPBA PCB Smdr SLISmtp STA WIM WANWLI Programming Guide