Dtrk Error Isdn or E1 card Fault | Samsung 7100 guide

CHAPTER 2. Ошибка! Стиль не определен.

			(continued)

No	Code	Alarm Name	Definition
-	MJD--	DTRK Error	ISDN or E1 card Fault
33	MJD01	Sync Failure	Clocking on TEPRI cards has become asynchronous.

34	MJD02	Sync Recovery	Clocking on TEPRI cards has become synchronous.

35	MJD03	Red Alarm	Locally detected loss of PCM carrier on TEPRI card for
			more than 250 ms.
			Alarm Data = Cabinet, Slot(Cx-Syy)

36	MJD04	Red Alarm Rec	PCM carrier detected locally on TEPRI cards.
			Alarm Data = Cabinet, Slot(Cx-Syy)

37	MJD05	Yellow Alarm	Remotely detected failure transmitted in frame on
			TEPRI card.
			Alarm Data = Cabinet, Slot(Cx-Syy)

38	MJD06	Yellow Alarm	Remotely detected failure restored transmitted on
		Rec	TEPRI card.
			Alarm Data = Cabinet, Slot(Cx-Syy)

39	MJD07	Blue Alarm	All 1's being transmitted on facility on TEPRI card.
			Alarm Data = Cabinet, Slot(Cx-Syy)
40	MJD08	Blue Alarm Rec	A blue alarm condition has been cleared.
			Alarm Data = Cabinet, Slot(Cx-Syy)

41	MJD09	Bit Error Alarm	Alarm is activated when the error rate exceeds 1 x 10-6
			errors. Note: 1x10-6is threshold for minor alarm, 1 x 10-3is
			threshold for major alarm errors on E1, PRI or BRI.
			Alarm Data = Cabinet, Slot(Cx-Syy)

42	MJD10	NTWRK Event	An Implausible event has occurred on the PRI or BRI
			Network digital line. Protocols do not match or sub-
			scriber ID mismatch.
			Alarm Data = Cabinet, Slot(Cx-Syy)

43	MJD11	SPID Init Error	The BRI received an error from the network.
			Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)

44	MJD12	SPID Init Rec	The BRI has recovered from an error on the network
			Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)

45	MJD13	LPBK Error	Internal on demand loopback failed.
			Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)
46	MJD14	LPBK Recovery	Internal on demand loopback test passed.
			Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)

47	MJD15	BRI DL Unavail	A BRI data link is out of service.
			Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)

48	MJD16	BRI DL Recovery	A BRI data link is back in service.
			Alarm Data = Cabinet, Slot, Channel(Cx-Syy-czz)

49	MJD17	RAM Error	An error has occurred in the TEPRI or BRI card RAM.
			Alarm Data = Cabinet, Slot(Cx-Syy)

2-340

Samsung Business Communications

Image 384

Samsung 7100 manual Dtrk Error Isdn or E1 card Fault

Contents

Programming Guide Copyright Trademarks Guide Contents PurposeAudience Conventions Console Screen Output Reference Guides Revision HistoryFirst Edition This page is intentionally left blank Symbols RestrictionInstruction Before using the Auto Record feature When changing the MMC 506, 807Compliance with the National Version Standards Table of Contents Overview of Programming Procedure MMC Programming 100 Assign Trunk Signal 414 MPD/PRS SignalSystem Timers STATION-WIDE Timers 177 TAX Rate Setup Enable Technician ProgramCustomer Access MMC Number Card PRE-INSTALL Abbreviation List of Figures Overview of MMC Pro Gramming DCS Euro Phones 24B LCD DCS Euro Phone 2 DS/ITP-5000 Series Phones DS-5038S Phone DS/ITP-5014D/5021D Phone DS-5014S/5007S Phone Using large LCD Phones Station Level Programming Station Level Programming listMMC No MMC Name Station Lock Operator Level Programming System Related MMC list Station Related MMC list Trunk Related MMC list Timer and Tone Related MMC list Group Related MMC list Tables, Codes, AA, Dect and VM MMC list MMC No MMC Name Tables, Codes, AA, Dect and VM MMC list SYS. I/O Mode Technician Level Programming listOptions MGI DSP Options Wlan Configuration Alarm ReportingSystem Alarm Assignments Maintenance Busy Alphabetically arranged Programming list MMC Name MMC No Assign ADD on Module BSI RF Carrier Confirm Outgoing Call Hardware Version Display Pickup Groups System SIO Mode VoIP Access Code MMC VoIP IP Table Program List by Function Phone Function Networking Function VoIP Function Wlan Function LCR Function12 VoIP Function Programming list MMC Program No Program Description Auto Attendant/Voice Mail Function Diagnosis Function Hotel FunctionPage MMC Programming Station Lock ALL Stations UnlockedType Description Assign COS Contents Assign Station COS Default passcodes Change User PasscodeALL Station Passcodes Call Forward NoneType System Timers STATION-WIDE Timers SET Answer Mode ALL Phones RingTo answer the C.O. call automatically Select all phones Dial 0, 1 or 2 to change ring mode Volume Up/Down keys Station NameDial Display shows Dial station number.e.g Station Speed Dial Program Buttons Assign Speed Block Station Speed Dial Name Station Speed Dial Key Feature Extender KEY Extender When using the Right Soft button Copy KEY ProgrammingStation KEY Programming System KEY Programming Station Status Status Description Pickup Groups Assign BOSS/SECRETARYAssign Station Group Assign Station to page Zone Mode Description Date DisplayCountry Western Clock 12 Hour Display Lower Case Assign Date and Time Feature Default Description Station ON/OFF See Description Some Options Depend on Country Not CONT.CIDAuto ANS CO OFF Enblock 2LCD OFF Assign COS Contents Phone Volume Phone Ring ToneFrequency Alarm Reminder Clock Alarms are NotsetNotset Today Alarm and Message View Memo Number Phone Volume Dial volume type.e.g SET Programmed Message No Messages Selected Alarm and Message Alarm Reminder Clock Edit Text Message Blank Message Conference Group Allow Group Conference Caller ID Display Number FirstAllow Caller ID Assign Review Block Large LCD Options Option Description MMC 719 Idle Display Phone Language EnglishLanguage None News Display Speed Answer Mode Executive StateExec State Statein Related Items Feature Description Show License StatusInvalid Disable SYSTEM-WIDE TimersOpen Customer Programming Change Customer Passcode Change Customer Passcode Passcode Change Feature Passcode Ring Plan Disa Alarm Alarm CLR Dect RegstWlan Regst Assign Disa Trunk When setting the MMC Assign UA DeviceCommon Bell Control Ringing Device Description Common Bell Control ContinuousAssign UA Device Assign Loud Bell Unassigned BARGE-IN Type No BARGE-INNo BARGE-IN With Tone When using the MMC Assign VM/AA PortNormal Port 1VMAA, 0NORMAL ICM Ring ICM RingCO Ring Data Ring Assign ADD-ON Module Masternone Option Default Description Customer ON/OFF PER Tenant Cancel VPN Enable OFFICM EXT FWD OFF Did ERR Tone OFF Cleaned SGR ALL OUT OFFChain FWD TRK Moniter OFF Voip Realrbt OFF CO-CO TM ALL OFFSmdr LOG OFF ALL Dial option number.e.g Door Ring Assignment Station Group Disa Alarm Ringing Station ALL Ring Plans Traffic Report Option Auto Print OFF Dial 0 for manual or 1 for automatic print Relay Type Isdn Service Type Voice Extension Type Normal Station Dial 0 5 to select station type FAX Pair Extension Type WAKE-UP Announcement AA Group None Message no None Group Busy NoneAA Group Message no Enter the AA group number Customer ON/OFF PER Station LCR Digit Table LCR Time Table Assign Station COS Enter the next ring plan class of service.e.g Pickup Groups No Pickup Groups AssignedKEY Extender Assign BOSS/SECRETARY Assign EXTENSION/TRUNK USE Dial YES ANS YES Copy Station Usable Assign Forced Code Account Code HOT LINE/OFF Hook Selection Assign Background Music Source Assign Trunk MOH Source Assign Station MOH Source Tone LCR Class of Service Least Cost Routing COSLCR Route Table Allow Caller ID RCV YES SND YESRCV SND Confirm Outgoing Call Confirm ToneDisconnect Customer SET Relocation Relocate 48B 64B IDCS Allowed 12B 24B28D 18D IDCS 28D SLT Euro 6B Euro 12B Euro 24B 48B AOM 64B AOM Copy Station Usable STATION/TRUNK USE Group Assign STATION/STATION USE Dial YES Distinctive Ringing ToneCadence Dial trunk or station number.e.g Branch Group MMC Preset Forward no Answer When using PRE FWD Busy option in MMCINT EXT Dial call type 0, 1 or 2.e.g Calling Party Number EmptyBRI Options PRI Options Ringback Tone Message Customer ON/OFF PER Trunk Display show Trunk LINE/PBX Line ALL Trunks CO Line Trunk Dial Type ALL Trunks DtmfDtmf Type Dial Pulse Type Trunk Toll Class ALL Trunks F-STNClass Description Enter day toll class.e.g., 2 for CLS-B Trunk Name Station Name Trunk CO TEL Number Entering Numbers ALL Trunks Ring Default Operator Group Trunk Ring AssignmentAssign Ring Plan Time Forced Trunk Release Assign Trunk MOH Source Trunk Status Read Follows Trunk Customer ON/OFF PER Trunk Trunk LINE/PBX LineTrunk Dial Type Trunk Toll Class Assign Disa Trunk ALL Trunks Normal Assign Trunk Signal Signalling condition typeImmediate Start 414 MPD/PRS Signal NonenormalPRS MPD TRUNK-WIDE Timers MMC Report Trunk Abandon Data ALL Trunks Report YESReport no Report YES 417 E1/PRI CRC4 Option CRC4 on BRI and PRI Card Restart Mode BRI Options Channel ANY YES Power Feed no Display shows first BRI channel Calling Party Number Trunk CO TEL NumberBRI & PRI Card Restart MSN Digit PRI Mode PRI OptionsNormal Same Connid Dial first PRI trunk number in PRI card.e.g MSN Digit CW YES OPT Accept Trunk COS ALL Ring Plans COS ALL TRK COS 423 S/T Mode BRI S0 MappingTrunk BRI S0 Mapping CID Trunks Normal Trunk Trunk Gain Control Trunk Gain Description Assign TRUNK/TRUNK USE Default Data Action Display SET H-TRK Cost Rate ALL TRUNKS/ALL Dial Plans ALL Cost Rates AssignedCosting Dial Plan Connection Status Display trunk connection status Display trunk status in conference Station Status Trunk TMC Gain Default Data Action 437 16TRK Gain Control Counter Default Description SYSTEM-WIDE CountersSee Description Enter number from above list.e.g System Timers Timer Name Default Range Unit Description Display Delay TM CO Confirm TimeCO-CO Disconnect Confirm Tone TM MCL Delay Time First Digit TimeHOK Flash MAX TM HOK Flash MIN TM Power Down Time MS LED on TimeOFF Hook Ring INT Ohva Answer Time See Description Some Timers Depend on Country When timers value is ‘0’ Display shows first timer value STATION-WIDE Timers Call Forward TRUNK-WIDE Timers Description Range Conn Delay Disa Answr 151 Pulse MAKE/BREAK Ratio MAKE/BREAK 33 Make Pulses PER Second 10 PPSMAKE/BREAK Ratio Pulse PER Second Assign Date and Time Type Description Range When changing the MMC Tone CadenceUnit milliseconds Terrupt Assign Ring Plan Time Start Time End Time Start None END None Ring Plan Call Cost Unit Cost PER MP 0200 PENCE, Call Cost Rate 100 PercentDisplay Description Unit Cost PER MP SLI Ring Cadence 160 MSG Waiting Lamp Cadence Interrupt LED 1000MS-ON 1000MS-OFFInterrupted Holiday Assignment No Holiday Assigned Follows Ring Plan Hotel Timer Room Clean TimeCheck OUT Time Check in END TM Tone Source Daylight Assignment No YY Start ENDAssign Date and Time Assign Operator Group Assign Station Group Type 1 UCDType 2 UCD Groups Calls to a group Normal Group Dial next feature option and continue Station Group Name Assign Trunk Group Trunk group LCR Programming Assign Station to page Zone No Stations Assigned Assign External page Zone Assign Speed Block System 200 Entries Stations 1 Block Assigned Station Speed Dial Name Assign System Speed Dial UCD Options Final Destination Ring Next TimeUCD Recall Time WRAP-UP Time Auto LOG OUT AlloutæfinalAgent PIN no Group Busy Next Press Volume button to select UCD group or dial Assign Review Block Phones 10 BinsSmdr Options Call LOG Block Allow Text Messaging Allow Group Conference STATION/TRUNK USE Group ALL Stations ALL Trunks NoneAssign STATION/STATION USE Assign TRUNK/TRUNK USE MGI Group Display shows the first available option MGI User Copy COS Contents Assign COS Contents Feature YES Flash YESFOLLOW-ME YES Forward YES REM. Hold YES RNG Plan YESSecure YES SET Rloc Dial COS.e.g Toll Deny Table ALL Entries are SET to Toll Allowance Table Toll Deny Table Assign Wild Character Entries SET to Z Entries SET to Assign System Speed Dial ANS/RLS System Speed Dial by Name No Names Assign System Speed Dial Authorization Code Assign Forced Code Account Code Toll Pass CODE/SPECIAL Code Table Special Code Description Toll Restriction LCR Digit Table LCR Digit 0001 Digit LCR Digit 0005 Digit LCR Time Table LCR Route Table LCR Class of Service LCR Modify Digit Table Digit String KEYOption Description Max. No. of Digit Entries NOF DEL DGT Enter digits to be appended.e.g Did Number and Name Translation DGTPRI Name Enter valid index numbere.g., 005 via dial keypad Enter call wait option via dial keypad Programmed Station Message Leave a Message On Vacation Gone Home UK LCR Option Network CodePIN Code CCC Option LCR Modify Digit Table UCD Agent ID UCD Options MY Area Code Idle Display Copy KEY Programming Restore Save Station KEY Programming BILLHotel Feature BOOTHHotel FeatureStation KEY Programming Message Cancel Path ReplacementEasy Alarm SET to Isdn Supplementary Service System Alarms TimerHeadset Mode Universal Answer Voice Mail Administration Enter selected station number.e.g System KEY Programming Type of Phone DescriptionBTN Sets EU 6B Sets See Default Data in MMC Dial Numbering Plan Type of Dial No Description Virt EXT Dial no MGI Dial noIP STN Dial no Wlan Dial no Chout None Choice NoneConf Conference Conp None Connected Name Display Credit None Reject None Ohva Reject Ring Plan RSV RTO None Ring Plan Time Override Selfid Self System ID See Description Feature Codes Depend on Country Dial option number to make selection.e.g Smdr Options Incoming AnswerIntercom Call KEY MMC IN/OUT Dial the option number.e.g System Version Display CID Translation Table When changing the COS Station Pair Costing Dial Plan MMC 749, Rate Calculation Table Cost Rate Rate Calculation Table ALL Cost Rates no DataCurrency values£ or € Dial option number 0-4.e.g VM Card Restart ALL Options are no MBX Download Assign Mailbox ALL Stations YES ALL Groups no Auto Record Dial VM number via dial keypad 5000 VM Halt Restart VM Alarm Threshold 80% When the first Built-In Voice Mail port is used for Vmmoh Assign VmmohNot Used VM IN/OUT IN/OUT VM DAY/NIGHT ALL Ring Plans DAY CLI Ringing CLIREJ Allow Caller ID Item Cost Table No EntriesCode Description Enter valid code numbere.g., 02 via dial TAX Rate Setup ALL Rates are %TAX Rate Value Enter the tax rate or value via dial keypad Room Cost Rate ALL Rates are 100% Option Description Default Second LCR LCR Class LCR TimeLCR Route Number Plan Enable Technician Program Default Passcode Change Technician Passcode Customer Access MMC Number TX Level and Gain SVMi Action Display Card PRE-INSTALL When a card is removed and a different type card is inserted Are YOU SURE?NO Phone Volume Control Phone Volume Level Depends on Phone Typeshown for 21D 21D Halt Processing Proc Reset System Clear MemoryFast Restart System Restart are YOU SURE?YES SET Country Code Hotel Timer TAX Rate SetupHotel Operation FAX Pair Customer Database Copy Clear McdbCopy to Sram Copy to Mcdb If you select YES, the display shows Program Download MC File Control File Name Description Press Volume button to confirm program type Assign System Link ID Assign Network TrunkAssign Network COS Ethernet Parameters Assign Network Trunk Normal Virtual Extension Type BTN SETLarge SET BTN LCD Enter virtual extension number Assign Network COS Dial the class of service number.01-30 Network Dial Translation Enter YES/NO to assign Mailbox to remote Assign Networking Options Dial the option number Assign System Reference Clock Priority 1 C1-S0 Priority 2 C1-S1 Priority 3 Self LAN Printer Parameters Enter type of data to be printed Ethernet Parameters Parameter Description CTI Server Addr Ethernet Parameters Display shows the system IP address MGI Parameters Version Card Reset no IP Type Private IP only VoIP Access Code Voip IP Table OptionsSIP Options Voip Access Code When changing IPVoIP IP Table TB00 ENTRY00 MMC 830 System IP Addr ALL Others Empty Parameter Description Default 834 H.323 Options Gateway Call ID Fast Setup Disable Fast Setup Enable MGI DSP Options Outband TOS FieldFAX Retry RTP CHK TM MGI Parameters 836 H.323 GK Options GRQ Send USE Multi E.164Lists GK Registered SIP Options Port Signal Port ProvisionalINV.NO Resp GEN.NO Registered GW Service Timer 0NONE, 1UPDATE, 2REINVITE ServerSIP GW Domain 315 SIP User Private IP Addresses IP Phone Information Upgrade Jitter BUFMMC 841 ITP DSP Para Down = Phone Data Time Zone MGI Group MGI UserMGI DSP Options System IP Options System IP Options CTI Link Option ITP DSP ParaSYS Data ITP TX GAIN/HSET Command ITP TX GAIN/MICITP RX GAIN/SPKR ITP Vers Show License Status Wlan Parameters Parameter Description Defaultms When the cursor is on WLAN, press Volume button BWBS=BASIC WBS Range is 0-99900 ms.Default 6000 ms WIP Information Wlan Configuration Wlan IP/MAC List Wlan IP/MAC List WIP Information Wlan Configuration Enter WEP KEY values when the WBS WEP SER System Resource Display Only MMC Dtmfr DSP’S CID DSP’S R2MFC DSP’S Conf GROUP’S Alarm Reporting View AlarmsClear Alarm BUF Print Alarm BUF Enter desired option System Alarm Assignments Alarm NotificationCode Alarm Name Definition MJA MCP2 Error System Fault Code Alarm Name Definition LCP/TASK Error LCP or Task FaultDSP Error System DSP Fault Dtrk Error Isdn or E1 card Fault MGI Error MGI card Fault Minor Error Minor Fault with Alarm Buffer saving Minor Error Minor Fault without Alarm Buffer saving Alarm Reporting Maintenance BusyALL OFF Maintenance Busy ALL Idle Display shows busy functions Diagnostic Time No Diagnostic Time SET Tech Programming Logs NnnnLAN Virtual Cabinet SET Type Range MMC 724 Number Plab MMC 822 VIR.EXT Type Hardware Version Display Only MMCMP Card System Options Auto Update Time Assign Speed Dial Block System Speed Dial Access NUM Node InfoTEL Number MAX Count Initialize Port AAA ACDALG AME Dasl DectDhcp Dpim IPC IpdcIPM IP-SCP OPX PATPBA PCB SLI SmdrSmtp STA WAN WIMWLI Programming Guide