System Alarm Assignments, Alarm Notification | Samsung 7100 specification

CHAPTER 2. Ошибка! Стиль не определен.

[852] SYSTEM ALARM ASSIGNMENTS

This MMC allows the assignment of system alarms to ring and display on stations that have an Alarm key assigned. The Alarm key is assigned in MMC 722(Station Key Pro- gramming). Alarm key programming is tenant wide(tenants 1 and 2). Alarms not pro- grammed to report to the system Alarm key will still be retained in the maintenance alarm buffer for Alarm Reporting(MMC 851). The alarm buffer holds up to 100 alarms on a First In-First Out(FIFO) basis. Pressing the Alarm key will silence the audible alarm until an- other alarm is generated by the system. Alarm conditions that have multiple causes(e.g., PRI errors and synchronization loss) will print all associated alarm information if an SIO port is programmed as an ALARM port. The specific fault alarm data can be displayed via MMC 851, System Alarm Reporting.

Alarm Notification

Alarm Notification Off/On(0/1) determines if the alarm provides a visual and audi- ble notification to the System Alarm key station(s). Pressing the System Alarm key and the release key will silence the audible alarm only at the station that pressed the System Alarm key and the release key. See alarm displays table for assignments.

Alarm Code Definitions:

No	Code	Alarm Name	Definition
-	MJA--	MCP2 Error	System Fault
01	MJA01	POR Restart	MCP2 restart process has been executed via power on
			restart.(POR)
02	MJA02	Soft Restart	MCP2 restart process has been executed via button reset.

03	MJA03	Mem Reset	The system RAM has been cleared via manual program-
			ming(PCMMC or KMMC) resulting in a system reset.
04	MJA04	MCP Reset	The MCP2 has software exception error.
			Alarm data = Reason
			- BUS ERR: Restart Bus Error
			- ADDR.ERR: Restart Address Error
			- ILLEGAL: Restart Illegal Opcode
			- ZERO DIVID: Restart Zero Divide
			- PRIVILEGE: Restart Privilege Violation
			- ENDL LOOP: Restart Endless Loop
05	MJA05	LCP Reset	The SCP2 or LCP2 has reset
			Alarm data = Cabinet(1, 2 or 3)

06	MJA06	PCM Switching	A fault has occurred in the Switching Control
			Alarm data = MCP BASE, ESM: 1, ESM: 2 or ESM: 3

2-338

Samsung Business Communications

Image 382

Samsung 7100 manual System Alarm Assignments, Alarm Notification, Code Alarm Name Definition MJA MCP2 Error System Fault

Contents

Programming Guide Copyright Trademarks Purpose Guide ContentsAudience Conventions Console Screen Output Revision History Reference GuidesFirst Edition This page is intentionally left blank Restriction SymbolsInstruction When changing the MMC 506, 807 Before using the Auto Record featureCompliance with the National Version Standards Table of Contents Overview of Programming Procedure MMC Programming 100 System Timers Assign Trunk Signal414 MPD/PRS Signal STATION-WIDE Timers 177 Customer Access MMC Number TAX Rate SetupEnable Technician Program Card PRE-INSTALL Abbreviation List of Figures Overview of MMC Pro Gramming DCS Euro Phones 24B LCD DCS Euro Phone 2 DS/ITP-5000 Series Phones DS-5038S Phone DS/ITP-5014D/5021D Phone DS-5014S/5007S Phone Using large LCD Phones MMC No MMC Name Station Level ProgrammingStation Level Programming list Station Lock Operator Level Programming System Related MMC list Station Related MMC list Trunk Related MMC list Timer and Tone Related MMC list Group Related MMC list Tables, Codes, AA, Dect and VM MMC list MMC No MMC Name Tables, Codes, AA, Dect and VM MMC list Options SYS. I/O ModeTechnician Level Programming list MGI DSP Options System Alarm Assignments Wlan ConfigurationAlarm Reporting Maintenance Busy Alphabetically arranged Programming list MMC Name MMC No Assign ADD on Module BSI RF Carrier Confirm Outgoing Call Hardware Version Display Pickup Groups System SIO Mode VoIP Access Code MMC VoIP IP Table Program List by Function Phone Function Networking Function VoIP Function 12 VoIP Function Programming list Wlan FunctionLCR Function MMC Program No Program Description Auto Attendant/Voice Mail Function Diagnosis Function Hotel FunctionPage MMC Programming ALL Stations Unlocked Station LockType Description Assign COS Contents Assign Station COS Change User Passcode Default passcodesALL Station Passcodes None Call ForwardType System Timers STATION-WIDE Timers ALL Phones Ring SET Answer ModeTo answer the C.O. call automatically Select all phones Dial 0, 1 or 2 to change ring mode Station Name Volume Up/Down keysDial Display shows Dial station number.e.g Station Speed Dial Program Buttons Assign Speed Block Station Speed Dial Name Station Speed Dial Key Feature Extender KEY Extender Station KEY Programming When using the Right Soft buttonCopy KEY Programming System KEY Programming Station Status Status Description Assign Station Group Pickup GroupsAssign BOSS/SECRETARY Assign Station to page Zone Date Display Mode DescriptionCountry Western Clock 12 Hour Display Lower Case Assign Date and Time Feature Default Description Station ON/OFF Auto ANS CO OFF See Description Some Options Depend on CountryNot CONT.CID Enblock 2LCD OFF Assign COS Contents Phone Ring Tone Phone VolumeFrequency Notset Alarm Reminder ClockAlarms are Notset Today Alarm and Message View Memo Number Phone Volume Dial volume type.e.g SET Programmed Message No Messages Selected Alarm and Message Alarm Reminder Clock Edit Text Message Blank Message Conference Group Allow Group Conference Allow Caller ID Caller ID DisplayNumber First Assign Review Block Large LCD Options Option Description MMC 719 Idle Display English Phone LanguageLanguage None News Display Speed Exec State Answer ModeExecutive State Statein Related Items Show License Status Feature DescriptionInvalid Open Customer Programming DisableSYSTEM-WIDE Timers Change Customer Passcode Change Customer Passcode Passcode Ring Plan Disa Alarm Alarm CLR Dect Regst Change Feature PasscodeWlan Regst Assign Disa Trunk Common Bell Control When setting the MMCAssign UA Device Ringing Device Description Continuous Common Bell ControlAssign UA Device Assign Loud Bell Unassigned No BARGE-IN BARGE-IN TypeNo BARGE-IN With Tone Normal Port When using the MMCAssign VM/AA Port 1VMAA, 0NORMAL CO Ring ICM RingICM Ring Data Ring Assign ADD-ON Module Masternone Option Default Description Customer ON/OFF PER Tenant ICM EXT FWD OFF CancelVPN Enable OFF Did ERR Tone OFF Chain FWD CleanedSGR ALL OUT OFF TRK Moniter OFF Smdr LOG OFF Voip Realrbt OFFCO-CO TM ALL OFF ALL Dial option number.e.g Door Ring Assignment Station Group Disa Alarm Ringing Station ALL Ring Plans Traffic Report Option Auto Print OFF Dial 0 for manual or 1 for automatic print Relay Type Isdn Service Type Voice Extension Type Normal Station Dial 0 5 to select station type FAX Pair Extension Type AA Group WAKE-UP AnnouncementAA Group None Message no None Group Busy None Message no Enter the AA group number Customer ON/OFF PER Station LCR Digit Table LCR Time Table Assign Station COS Enter the next ring plan class of service.e.g No Pickup Groups Assigned Pickup GroupsKEY Extender Assign BOSS/SECRETARY Assign EXTENSION/TRUNK USE Dial YES ANS YES Copy Station Usable Assign Forced Code Account Code HOT LINE/OFF Hook Selection Assign Background Music Source Assign Trunk MOH Source Assign Station MOH Source Tone Least Cost Routing COS LCR Class of ServiceLCR Route Table RCV Allow Caller IDRCV YES SND YES SND Confirm Tone Confirm Outgoing CallDisconnect Customer SET Relocation 28D 18D Relocate48B 64B IDCS Allowed 12B 24B IDCS 28D SLT Euro 6B Euro 12B Euro 24B 48B AOM 64B AOM Copy Station Usable STATION/TRUNK USE Group Assign STATION/STATION USE Dial YES Tone Distinctive RingingCadence Dial trunk or station number.e.g Branch Group MMC INT Preset Forward no AnswerWhen using PRE FWD Busy option in MMC EXT Dial call type 0, 1 or 2.e.g BRI Options Calling Party NumberEmpty PRI Options Ringback Tone Message Customer ON/OFF PER Trunk Display show Trunk LINE/PBX Line ALL Trunks CO Line Dtmf Type Trunk Dial TypeALL Trunks Dtmf Dial Pulse Type ALL Trunks F-STN Trunk Toll ClassClass Description Enter day toll class.e.g., 2 for CLS-B Trunk Name Station Name Trunk CO TEL Number Entering Numbers Trunk Ring Assignment ALL Trunks Ring Default Operator GroupAssign Ring Plan Time Forced Trunk Release Assign Trunk MOH Source Trunk Status Read Follows Trunk Trunk Dial Type Customer ON/OFF PER TrunkTrunk LINE/PBX Line Trunk Toll Class Assign Disa Trunk ALL Trunks Normal Signalling condition type Assign Trunk SignalImmediate Start PRS 414 MPD/PRS SignalNonenormal MPD TRUNK-WIDE Timers MMC Report no Report Trunk Abandon DataALL Trunks Report YES Report YES 417 E1/PRI CRC4 Option CRC4 on BRI and PRI Card Restart Mode BRI Options Channel ANY YES Power Feed no Display shows first BRI channel BRI & PRI Card Restart Calling Party NumberTrunk CO TEL Number MSN Digit Normal PRI ModePRI Options Same Connid Dial first PRI trunk number in PRI card.e.g MSN Digit CW YES OPT Accept Trunk COS ALL Ring Plans COS ALL TRK COS BRI S0 Mapping 423 S/T ModeTrunk BRI S0 Mapping CID Trunks Normal Trunk Trunk Gain Control Trunk Gain Description Assign TRUNK/TRUNK USE Default Data Action Display SET H-TRK ALL TRUNKS/ALL Dial Plans ALL Cost Rates Assigned Cost RateCosting Dial Plan Connection Status Display trunk connection status Display trunk status in conference Station Status Trunk TMC Gain Default Data Action 437 16TRK Gain Control SYSTEM-WIDE Counters Counter Default DescriptionSee Description Enter number from above list.e.g System Timers Timer Name Default Range Unit Description CO-CO Disconnect Display Delay TMCO Confirm Time Confirm Tone TM HOK Flash MAX TM MCL Delay TimeFirst Digit Time HOK Flash MIN TM OFF Hook Ring INT Power Down TimeMS LED on Time Ohva Answer Time See Description Some Timers Depend on Country When timers value is ‘0’ Display shows first timer value STATION-WIDE Timers Call Forward TRUNK-WIDE Timers Description Range Conn Delay Disa Answr 151 MAKE/BREAK Ratio Pulse MAKE/BREAK RatioMAKE/BREAK 33 Make Pulses PER Second 10 PPS Pulse PER Second Assign Date and Time Type Description Range Tone Cadence When changing the MMCUnit milliseconds Terrupt Assign Ring Plan Time Start Time End Time Start None END None Ring Plan Display Description Call CostUnit Cost PER MP 0200 PENCE, Call Cost Rate 100 Percent Unit Cost PER MP SLI Ring Cadence 160 Interrupt LED 1000MS-ON 1000MS-OFF MSG Waiting Lamp CadenceInterrupted Holiday Assignment No Holiday Assigned Follows Ring Plan Check OUT Time Hotel TimerRoom Clean Time Check in END TM Tone Source No YY Start END Daylight AssignmentAssign Date and Time Assign Operator Group Type 1 UCD Assign Station GroupType 2 UCD Groups Calls to a group Normal Group Dial next feature option and continue Station Group Name Assign Trunk Group Trunk group LCR Programming Assign Station to page Zone No Stations Assigned Assign External page Zone Assign Speed Block System 200 Entries Stations 1 Block Assigned Station Speed Dial Name Assign System Speed Dial UCD Options UCD Recall Time Final DestinationRing Next Time WRAP-UP Time Agent PIN no Auto LOG OUTAlloutæfinal Group Busy Next Press Volume button to select UCD group or dial Phones 10 Bins Assign Review BlockSmdr Options Call LOG Block Allow Text Messaging Allow Group Conference Assign STATION/STATION USE STATION/TRUNK USE GroupALL Stations ALL Trunks None Assign TRUNK/TRUNK USE MGI Group Display shows the first available option MGI User Copy COS Contents Assign COS Contents FOLLOW-ME YES Feature YESFlash YES Forward YES Secure YES REM. Hold YESRNG Plan YES SET Rloc Dial COS.e.g Toll Deny Table ALL Entries are SET to Toll Allowance Table Toll Deny Table Assign Wild Character Entries SET to Z Entries SET to Assign System Speed Dial ANS/RLS System Speed Dial by Name No Names Assign System Speed Dial Authorization Code Assign Forced Code Account Code Toll Pass CODE/SPECIAL Code Table Special Code Description Toll Restriction LCR Digit Table LCR Digit 0001 Digit LCR Digit 0005 Digit LCR Time Table LCR Route Table LCR Class of Service Option Description Max. No. of Digit Entries LCR Modify Digit TableDigit String KEY NOF DEL DGT Enter digits to be appended.e.g PRI Did Number and Name TranslationDGT Name Enter valid index numbere.g., 005 via dial keypad Enter call wait option via dial keypad Programmed Station Message Leave a Message On Vacation Gone Home PIN Code UK LCR OptionNetwork Code CCC Option LCR Modify Digit Table UCD Agent ID UCD Options MY Area Code Idle Display Copy KEY Programming Restore Save Station KEY Programming BOOTHHotel Feature BILLHotel FeatureStation KEY Programming Easy Alarm SET to Message CancelPath Replacement Isdn Supplementary Service Headset Mode Universal Answer System AlarmsTimer Voice Mail Administration Enter selected station number.e.g BTN Sets System KEY ProgrammingType of Phone Description EU 6B Sets See Default Data in MMC Dial Numbering Plan Type of Dial No Description IP STN Dial no Virt EXT Dial noMGI Dial no Wlan Dial no Conf Conference Conp None Connected Name Display Chout NoneChoice None Credit None Reject None Ohva Reject Ring Plan RSV RTO None Ring Plan Time Override Selfid Self System ID See Description Feature Codes Depend on Country Dial option number to make selection.e.g Smdr Options Intercom Call IncomingAnswer KEY MMC IN/OUT Dial the option number.e.g System Version Display CID Translation Table When changing the COS Station Pair Costing Dial Plan MMC 749, Rate Calculation Table Cost Rate ALL Cost Rates no Data Rate Calculation TableCurrency values£ or € Dial option number 0-4.e.g VM Card Restart ALL Options are no MBX Download Assign Mailbox ALL Stations YES ALL Groups no Auto Record Dial VM number via dial keypad 5000 VM Halt Restart VM Alarm Threshold 80% Assign Vmmoh When the first Built-In Voice Mail port is used for VmmohNot Used VM IN/OUT IN/OUT VM DAY/NIGHT ALL Ring Plans DAY CLI CLI RingingREJ Allow Caller ID No Entries Item Cost TableCode Description Enter valid code numbere.g., 02 via dial TAX Rate TAX Rate SetupALL Rates are % Value Enter the tax rate or value via dial keypad Room Cost Rate ALL Rates are 100% Option Description Default Second LCR LCR Route LCR ClassLCR Time Number Plan Enable Technician Program Default Passcode Change Technician Passcode Customer Access MMC Number TX Level and Gain SVMi Action Display Card PRE-INSTALL When a card is removed and a different type card is inserted Are YOU SURE?NO Phone Volume Control Phone Volume Level Depends on Phone Typeshown for 21D 21D Halt Processing Proc Fast Restart Reset SystemClear Memory System Restart are YOU SURE?YES SET Country Code Hotel Operation Hotel TimerTAX Rate Setup FAX Pair Copy to Sram Customer Database CopyClear Mcdb Copy to Mcdb If you select YES, the display shows Program Download MC File Control File Name Description Press Volume button to confirm program type Assign Network COS Assign System Link IDAssign Network Trunk Ethernet Parameters Assign Network Trunk Normal Large SET Virtual Extension TypeBTN SET BTN LCD Enter virtual extension number Assign Network COS Dial the class of service number.01-30 Network Dial Translation Enter YES/NO to assign Mailbox to remote Assign Networking Options Dial the option number Assign System Reference Clock Priority 1 C1-S0 Priority 2 C1-S1 Priority 3 Self LAN Printer Parameters Enter type of data to be printed Ethernet Parameters Parameter Description CTI Server Addr Ethernet Parameters Display shows the system IP address MGI Parameters Version Card Reset no IP Type Private IP only VoIP Access Code Options Voip IP TableSIP Options VoIP IP Table Voip Access CodeWhen changing IP TB00 ENTRY00 MMC 830 System IP Addr ALL Others Empty Parameter Description Default 834 H.323 Options Gateway Call ID Fast Setup Disable Fast Setup Enable MGI DSP Options FAX Retry OutbandTOS Field RTP CHK TM MGI Parameters 836 H.323 GK Options Lists GRQ SendUSE Multi E.164 GK Registered SIP Options INV.NO Resp Port Signal PortProvisional GEN.NO SIP Registered GW ServiceTimer 0NONE, 1UPDATE, 2REINVITE Server GW Domain 315 SIP User Private IP Addresses IP Phone Information MMC 841 ITP DSP Para Down = Phone Data UpgradeJitter BUF Time Zone MGI DSP Options MGI GroupMGI User System IP Options System IP Options SYS Data CTI Link OptionITP DSP Para ITP TX GAIN/HSET ITP RX GAIN/SPKR CommandITP TX GAIN/MIC ITP Vers Show License Status Wlan Parameters Parameter Description Defaultms When the cursor is on WLAN, press Volume button BWBS=BASIC WBS Range is 0-99900 ms.Default 6000 ms WIP Information Wlan Configuration Wlan IP/MAC List Wlan IP/MAC List WIP Information Wlan Configuration Enter WEP KEY values when the WBS WEP SER System Resource Display Only MMC Dtmfr DSP’S CID DSP’S R2MFC DSP’S Conf GROUP’S Clear Alarm BUF Alarm ReportingView Alarms Print Alarm BUF Enter desired option Alarm Notification System Alarm AssignmentsCode Alarm Name Definition MJA MCP2 Error System Fault LCP/TASK Error LCP or Task Fault Code Alarm Name DefinitionDSP Error System DSP Fault Dtrk Error Isdn or E1 card Fault MGI Error MGI card Fault Minor Error Minor Fault with Alarm Buffer saving Minor Error Minor Fault without Alarm Buffer saving Maintenance Busy Alarm ReportingALL OFF Maintenance Busy ALL Idle Display shows busy functions Diagnostic Time No Diagnostic Time SET Nnnn Tech Programming LogsLAN Virtual Cabinet SET Type Range MMC 724 Number Plab MMC 822 VIR.EXT Type Only MMC Hardware Version DisplayMP Card System Options Auto Update Time Assign Speed Dial Block System Speed Dial TEL Number Access NUMNode Info MAX Count Initialize Port ALG AAAACD AME Dhcp DaslDect Dpim IPM IPCIpdc IP-SCP PBA OPXPAT PCB Smtp SLISmdr STA WIM WANWLI Programming Guide