Teledyne M300EM operation manual Calibration Procedures

Table of Contents	Teledyne API – Technical Manual - Model 300E Family CO Analyzers
8.1.7. Terminal Operating Modes			156
8.1.7.1. Help Commands in Terminal Mode			156
8.1.7.2. Command Syntax			157
8.1.7.3. Data Types			157
8.1.7.4. Status Reporting			158
8.1.7.5. COMM Port Password Security			159
8.2. Multidrop RS-232 Set Up			160
8.3. RS-485 Configuration of COM2			162
8.4. Remote Access via the Ethernet			164
8.4.1. Ethernet Card COM2 Communication Modes and Baud Rate			164
8.4.2. Configuring the Ethernet Interface Option using DHCP			165
8.4.3. Manually Configuring the Network IP Addresses			167
8.4.4. Changing the Analyzer’s HOSTNAME			170
8.5. MODBUS SetUp			171
8.5.1. Remote Access by Modem			172
8.6. Using the M300E/EM with a Hessen Protocol Network			175
8.6.1. General Overview of Hessen Protocol			175
8.6.2. Hessen COMM Port Configuration			175
8.6.3. Activating Hessen Protocol			176
8.6.4. Selecting a Hessen Protocol Type			177
8.6.5. Setting The Hessen Protocol Response Mode			178
8.6.6. Hessen Protocol Gas List Entries			179
8.6.6.1. Gas List Entry Format and Definitions			179
8.6.6.2. Editing or Adding HESSEN Gas List Entries			180
8.6.6.3. Deleting HESSEN Gas List Entries			181
8.6.7. Setting Hessen Protocol Status Flags			182
8.6.8. Instrument ID Code			183
8.7. APICOM Remote Control Program			184
9. CALIBRATION PROCEDURES			185
9.1. Before Calibration			186
9.1.1. Required Equipment, Supplies, and Expendables			186
9.1.2. Calibration Gases			186
9.1.2.1. Zero Air			186
9.1.2.2. Span Gas			187
9.1.2.3. Traceability			187
9.1.3. Data Recording Devices			187
9.2. Manual Calibration Checks and Calibration of the M300E/EM Analyzer in its Base Configuration			.......... 188
9.2.1. Setup for Basic Calibration Checks and Calibration			188
9.2.2. Performing a Basic Manual Calibration Check			190
9.2.3. Performing a Basic Manual Calibration			191
9.2.3.1. Setting the Expected Span Gas Concentration			191
9.2.3.2. Zero/Span Point Calibration Procedure			192
9.3. Manual Calibration with Zero/Span Valves			193
9.3.1. Setup for Calibration Using Valve Options			193
9.3.2. Manual Calibration Checks with Valve Options Installed			195
9.3.3. Manual Calibration Using Valve Options			196
9.3.3.1. Setting the Expected Span Gas Concentration			196
9.3.3.2. Zero/Span Point Calibration Procedure			197
9.3.3.3. Use of Zero/Span Valve with Remote Contact Closure			198
9.4. Automatic Zero/Span Cal/Check (AutoCal)			198
9.4.1. SETUP  ACAL: Programming and AUTO CAL Sequence			201
9.4.1.1. AutoCal with Auto or Dual Reporting Ranges Modes Selected			203
9.5. CO Calibration Quality			204
9.6. Calibration of the M300E/EM’s Electronic Subsystems			205
9.6.1. Dark Calibration Test			205
9.6.2. Pressure Calibration			206
9.6.3. Flow Calibration			207
9.6.4. Electrical Test Calibration			208
xii		04288D DCN5752