Teledyne M300EM Specifications And Approvals, 1:M 300E/300EM Basic Unit Specifications

Teledyne API – Technical Manual - Model 300E Family CO Analyzers Specifications and Approvals

2.SPECIFICATIONS AND APPROVALS

2.1.SPECIFICATIONS

Table 2-1: M 300E/300EM Basic Unit Specifications

Ranges	M300E: Min: 0-1 ppm; Max: 0-1000 ppm of Full Scale (User selectable)
	M300EM: Min: 0-5 ppm; Max: 0-5000 ppm of Full Scale (User selectable)
Measurement Units	M300E: ppb, ppm, µg/m3, mg/m3 (user selectable)
	M300EM: ppm, mg/m3	(user selectable)
Zero Noise	M300E: < 0.02 ppm RMS1;M300EM: ≤ 0.1 ppm RMS
Span Noise	M300E:<0.5% of rdg RMS over 5ppm1, 3;		M300EM:>0.5% of rdg RMS over 20ppm
Lower Detectable Limit1	M300E: < 0.04 ppm;	M300EM: 0.2 ppm
Zero Drift (24 hours) 2	M300E: < 0.1 ppm;	M300EM: <0.5 ppm
Zero Drift (7 days) 2	M300E: < 0.2 ppm;	M300EM: <1.0ppm
Span Drift (24 hour2s)	The greater of < 0.5% of reading or 0.1ppm (M300E), 0.5ppm(M300EM)
Span Drift (7 days) 2	The greater of < 1% of reading or 0.5ppm (M300E), 1 ppm(M300EM)
Linearity	M300E: Better than 1% Full Scale5;
	M300EM: 0 - 3000 ppm: 1% full scale;		3000 - 5000 ppm: 2% full scale
Precision	M300E: The greater of 0.5% of reading or 0.2ppm;
	M300EM: The greater of 1.0% of reading or 1ppm
Lag Time 1	10 sec1
Rise/Fall Time 1	<60 sec to 95%1
Sample Flow Rate	800 cm3/min. ±10%
	O2 Sensor option adds 120 cm³/min to total flow though when installed
Temperature Range	5 - 40°C operating, 10 - 40°C EPA Equivalency (M300E only)
Humidity Range	0-95% RH, Non-Condensing
Temp Coefficient	< 0.05 % per °C (minimum 50 ppb/°C)
Voltage Coefficient	< 0.05 % per V
Dimensions (HxWxD)	7" x 17" x 23.5" (178 mm x 432 mm x 597 mm)
Weight	50 lb (22.7 kg)
AC Power	100V 50/60 Hz (3.25A), 115 V 60 Hz (3.0A),
	220 – 240 V 50/60 Hz (2.5A)
Environmental Conditions	Installation Category (Over voltage Category) II Pollution Degree 2
Analog Outputs	4 user configurable outputs
Analog Output Ranges	All Outputs: 0.1V, 1V, 5V or 10V
	Three outputs convertible to 4-20 mA isolated current loop.
	All Ranges with 5% under/over-range
Analog Output Resolution	1 part in 4096 of selected full-scale voltage
Status Outputs	8 Status outputs from opto-isolators
Control Inputs	6 Control Inputs, 2 defined, 4 spare
Serial I/O	One (1) RS-232/optional multidrop; One (1) RS-232/optional RS-485 (2 connecters in
	parallel)
	Baud Rate : 300 - 115200
Alarm outputs (optional)	2 opto-isolated alarm outputs and 2 dry contact alarm outputs
Certifications	USEPA: Reference Method Number EQOA-0992-087
	CE: EN61010-1:90 + A1:92 + A2:95, EN61326 - Class A
1 As defined by the USEPA	2 At constant temperature and pressure

04288D DCN5752 27