System Operations | |
|
|
EN 15
To arm the system in STAY Mode 1 (method one):
1.Enter your code and press [STAY].
2.Two beeps sound and the STAY indicator is lit. Exit Time starts.
The indicators for any zones that are programmed to be automatically isolated in STAY Mode 1 begin to flash until Exit Time expires. At the end of Exit Time, the zone indicators are extinguished and the codepad sounds one short beep.
To arm the system in STAY Mode 1 (method two):
1.Press and hold [STAY].
2.When two beeps sound, release the button. The STAY indicator is lit and Exit Time starts.
The indicators for any zones that are programmed to be automatically isolated in STAY Mode 1 flash until Exit Time expires. At the end of Exit Time, the zone indicators are extinguished and the codepad sounds one short beep.
If a zone is not sealed at the end of Exit Time, the zone is automatically isolated and is lit constantly on the remote codepad. The zone becomes an active part of the system again as soon as it is resealed. For example, if a window is open when Exit Time expires, the window does not become an active part of the system until it is closed. Opening the window after Exit Time expires causes an alarm.
Forced Arming
Arming the system when a zone is not sealed is known as forced arming. Refer to Section 14.3.7 Zone Options 2 on page 63 to enable forced arming for each zone.
If the STAY indicator does not light and a long beep sounds when you attempt to arm the system in STAY Mode 1, forced arming is not permitted. If this is the case, you must seal all zones or manually isolate them before you can arm the system.
3.4Disarming the System from STAY Mode 1
There are two methods to disarm the system from STAY Mode 1. You can always use the first method. You can use method two only if Option 4 is enabled in Location 497 (refer to Section 18.6 Consumer Options 2 on page 83).
To disarm the system from STAY Mode 1 (method one):
1.Enter your code and press [STAY].
2.Two beeps sound and the STAY indicator is extinguished. The system is now disarmed.
To disarm the system from STAY Mode 1 (method two):
A flashing zone indicator represents a previous alarm in that zone. If this is the case, a valid User Code is required to disarm the system using method one. To enable method two, Option 4 in Location 497 must be enabled (refer to Section 18.6 Consumer Options 2 on page 83).
1.Press and hold [STAY].
2.When two beeps sound, release the button. The STAY indicator is extinguished and the system is disarmed.
Single button disarming from STAY
Mode 1 reports as User Code 16.
3.5Arming The System in STAY Mode 2
STAY Mode 2 is used when you need to arm the perimeter and unused areas of the premises to detect
a
You can program zones to be automatically isolated in STAY Mode 2 using an Installer Code function (refer to Section 5.1.5) or a Master Code function (Section 5.2.6).
If the system reports to a base station, it sends a Partial Close Report (Contact ID Event Code 456).
Entry Guard Timer for STAY Mode
When arming the system in STAY Mode 2, an optional entry timer called Entry Guard Timer for STAY Mode can be used to delay the sirens, strobe, and bell outputs if a zone that is not automatically isolated activates an alarm. Entry Guard Timer for STAY Mode is the delay time used for all zones, except
If the Entry Guard Timer for STAY Mode is programmed and a zone that was not automatically isolated is activated, the codepad beeps twice per sec until the Entry Guard Timer for STAY Mode expires or the system is disarmed. If the alarm is not reset before Entry Guard Timer for STAY Mode expires, the strobe, bell, and siren outputs are activated into alarm.
Single button disarming from STAY
Mode 2 reports as User Code 16.
To arm the system in STAY Mode 2:
1.Press and hold [0].
2.When two beeps sound, release the button. The STAY indicator is lit and the Exit Time starts.
Bosch Security Systems, Inc. 12/08
