Dialer Information | |
|
|
EN 51
Table 46: Telco Arm/Disarm Dialing Digits
Digit | Number to | Digit | Number to |
Required | Program | Required | Program |
terminator | 0 | 8 | 8 |
1 | 1 | 9 | 9 |
2 | 2 | 0 | 10 |
3 | 3 | * | 11 |
4 | 4 | # | 12 |
5 | 5 | 4 sec pause | 13 |
6 | 6 | break | 14 |
7 | 7 | 15 | 15 |
To turn call forward (immediate) on, enter:
[* 2 1][forwarding telephone number][#]
Example
To immediately forward all incoming calls to the telephone number 96721055 after arming the system in AWAY Mode, program:
[11 | 2 1 9 6 | 7 2 1 | 10 | 5 5 | 12 | 0 0 0 0 0 0 0 0 0 0 0 0 |
0 0 0 0 0 0] |
|
|
|
|
| |
To turn call forward (no answer) on, enter:
[* 6 1][forwarding telephone number][#]
Example
To forward all incoming calls, when there is no answer, to the telephone number 96721055 after arming the system in AWAY Mode, program:
[11 | 6 1 9 6 | 7 2 1 | 10 | 5 5 | 12 | 0 0 0 0 0 0 0 0 0 0 0 0 |
0 0 0 0 0 0] |
|
|
|
|
| |
11.8Telco Disarming Sequence
Location 143 to 158
Default 0
These locations allow you to deactivate call diversion automatically on your telephone when you disarm the system from AWAY Mode.
To turn call forward (immediate) off, enter:
[# 2 1 #]
Example
To disable call forward (immediate) after disarming the system from AWAY Mode, program:
[12 2 1 12 0 0 0 0 0 0 0 0 0 0 0 0]
To turn call forward (no answer) off, enter:
[# 6 1 #]
Example
To disable call forward (no answer) after disarming the system from AWAY Mode, program:
[12 6 1 12 0 0 0 0 0 0 0 0 0 0 0 0]
11.9Call Back Telephone Number
Location 159 to 174
Default 0
This location stores the telephone number to call when Upload/Download is requested or the user holds down [6] to initiate a modem call from the control panel to establish a communications link with the remote computer. The computer must be running the CC816 Alarm Link Software and must be set to Waiting for an Incoming Call. The Call Back Telephone Number is also required if Remote Connection with Callback Verification is required (refer to Section 8.1.3 on page 41).
Refer to Section 8.0 Alarm Link Software on page 40 for more information.
11.10 Ring Count
Location 175
Default 8
0Panel does not answer
1 to 13 Number of rings until panel answers
14Answering machine bypass 2
15Answering machine bypass 1
This location sets the number of rings before the control panel answers an incoming call. Set this count to an acceptable level, noting that one ring is “Ring, Ring – Ring, Ring” and that a Ring Count of 10 represents approximately 60 sec. This location has an effect only if Remote Arming, remote Upload/Download using Alarm Link, or both are enabled. Programming this location to 0 prevents the control panel from answering incoming calls regardless of other programmed options.
Answering Machine Bypass
Answering Machine Bypass allows a connection with the control panel for Remote Arming or Upload/Download when an answering machine or facsimile machine is on the same telephone line. Answering Machine Bypass has two different methods. Program a 14 to use the secondary method only when there is a large amount of traffic on the line (at a home office, for example). This method reduces the chance of the control panel incorrectly answering an incoming call.
Programming the Ring Count to 15 enables Answering Machine Bypass in the primary mode. When calling the control panel, allow the telephone to ring no more than four times and then hang up. If you call again within 45 sec, the control panel answers the call on the first ring and the connection is established. This prevents the answering machine or facsimile machine from answering the call. To enable Answering Machine Bypass only when the system is armed, select Option 2 in Location 177 (refer to Section 12.1 Dialer Options 1 on page 52).
Bosch Security Systems, Inc. 12/08
