System Functions | |
|
|
EN 33
For more information, refer to Section 5.1.5 Setting STAY Mode 2 Zones on page 25 (using the Installer Code function) or Section 5.2.6 Setting STAY Mode 2 Zones on page 25 (using the Master Code function).
STAY Mode 2 is not available on partitioned
5.4.4Horn Speaker Test
Holding down [1] until two beeps sound activates the horn speaker for a
5.4.5Bell Test
Holding down [2] until two beeps sound activates the internal screamers for a
If the SS914 Satellite Siren (EDMSAT) is connected to the control panel, this function tests both the horn speaker and the strobe connected to the satellite siren for a
5.4.6Strobe Test
Holding down [3] operates the strobe. No other device operates during this mode.
If the SS914 Satellite Siren (EDMSAT) is connected to the control panel, this function also tests the strobe on the satellite siren.
To turn the strobe test on:
Press and hold [3] until three beeps sound. The strobe flashes.
To turn the strobe test off:
Press and hold [3] until two beeps sound. The strobe stops flashing.
5.4.7Turning Day Alarm On and Off
Holding down [4] turns Day Alarm on or off. If you want the STAY indicator to indicate the status of Day Alarm operation (enabled or disabled), select Option 8 in Location 484 (refer to Section 18.5 Consumer Options 1 on page 82). When this option is selected, the STAY indicator flashes once every 3 sec when Day Alarm is active.
To turn Day Alarm on:
Press and hold [4] until three beeps sound.
To turn Day Alarm off:
Press and hold [4] until two beeps sound.
5.4.8Fault Analysis Mode
Several system faults can be detected by the control panel. When any of these faults are present, the FAULT indicator flashes and the codepad beeps once per min. Refer to Section 3.12 Fault Analysis Mode on page 18 for more information on each fault type.
To determine the type of fault:
Press and hold [5] until two beeps sound.
The STAY, AWAY, and FAULT indicators flash. One or more zone indicators (1 to 8) light to indicate the type of fault that occurred. Refer to Table 15 on page 20.
To exit from Fault Analysis Mode:
Press [AWAY].
The STAY and AWAY indicators are extinguished and the system returns to the disarmed state.
5.4.9Initiate a Modem Call
Holding down [6] until two beeps sound forces the control panel to dial the callback telephone number programmed in Locations 159 to 174 (refer to Section
11.9Call Back Telephone Number on page 51) in an attempt to connect to the installer’s remote computer.
The remote computer must be running the CC816 Alarm Link Software and must be set to Waiting for an Incoming Call. If no callback telephone number is programmed, holding down [6] has no effect.
5.4.10Reset Latching Outputs
Holding down [7] until two beeps sound resets any output that is programmed to remain on after it is activated.
The output must be programmed with a latching polarity. Refer to Section 16.3 Output Polarity on page 76 for more information.
5.4.11Change the Codepad Buzzer Tone
Holding down [8] down continuously changes the tone of the buzzer in the remote codepad. There are 50 different tones from 1500 Hz to 5000 Hz. In an installation with multiple codepads, you can set a different tone for each codepad.
To change the buzzer tone:
1.Press and hold [8] continuously.
The tone of the buzzer increases in pitch.
2.Release [8] button when you hear the desired tone.
Every time the system is powered down, you must reset each codepad to its individual tone using this function.
On partitioned
Bosch Security Systems, Inc. 12/08
