RF Information | |
|
|
EN 89
8 – Enable RF Jamming Monitor
If this option is selected, the RF receiver monitors the background RF levels. If this level reaches a preset limit, the receiver assumes it is being jammed. This generates a fault on the codepad and sends an RF Jamming Report to the monitoring station.
20.2RF Device Mapping Option
Location | 600 to 615 |
|
|
|
| Location | Default |
Map RF Device 1 | 600 | 1 | |
Map RF Device 2 | 601 | 1 | |
Map RF Device 3 | 602 | 1 | |
Map RF Device 4 | 603 | 1 | |
Map RF Device 5 | 604 | 1 | |
Map RF Device 6 | 605 | 1 | |
Map RF Device 7 | 606 | 1 | |
Map RF Device 8 | 607 | 1 | |
Map RF Device 9 | 608 | 1 | |
Map RF Device 10 | 609 | 1 | |
Map RF Device 11 | 610 | 1 | |
Map RF Device 12 | 611 | 1 | |
Map RF Device 13 | 612 | 1 | |
Map RF Device 14 | 613 | 1 | |
Map RF Device 15 | 614 | 1 | |
Map RF Device 16 | 615 | 1 | |
0 | Mapping Disabled |
| |
1 | Mapping Enabled |
| |
|
|
|
|
These locations allow you to enable or disable any of the sixteen RF devices. For example, if location 607 is set to “0”, RF device 7 is not mapped and is disabled.
20.3Default RF Device Mapping (Devices 1 to 8)
Location | 616 to 623 |
|
|
|
| Location | Default Value* |
Map RF Device 1 to Zone | 616 | 00 | |
(1 to 16) |
|
|
|
Map RF Device 2 to Zone | 617 | 01 | |
(1 to 16) |
|
|
|
Map RF Device 3 to Zone | 618 | 02 | |
(1 to 16) |
|
|
|
Map RF Device 4 to Zone | 619 | 03 | |
(1 to 16) |
|
|
|
Map RF Device 5 to Zone | 620 | 04 | |
(1 to 16) |
|
|
|
Map RF Device 6 to Zone | 621 | 05 | |
(1 to 16) |
|
|
|
Map RF Device 7 to Zone | 622 | 06 | |
(1 to 16) |
|
|
|
Map RF Device 8 to Zone | 623 | 07 | |
(1 to 16) |
|
|
|
Mapping RF device to zone | |||
|
|
|
|
*The programming for zone numbers 1 through 8 is in hexadecimal code (00 through 15).
These locations allow you to allocate RF wireless devices 1 to 8 to any of the 16 zones on the control panel. You cannot map more than one RF wireless device to the same zone. Refer to Section 20.4 Default RF Device Mapping (Devices 9 to 16) to map RF wireless devices 9 to 16. By default, RF devices 1 to 8 are mapped separately to each of the eight zones (that is, Device 1 is mapped to Zone 1, Device 2 to Zone 2, and so on). Locations 616 to 623 and locations 624 to 631 can be programmed as any value from 00 to 15. Refer to Section 20.5 Using Hexadecimal Values for RF Device Mapping on page 89 for mapping information.
20.4Default RF Device Mapping (Devices 9 to 16)
Location |
| 624 to 631 |
|
|
|
|
|
|
| Location | Default |
Map RF Device 9 to Zone | 624 | 08 | |||
(1 to 16) |
|
|
|
|
|
Map RF Device 10 to | 625 | 09 | |||
Zone (1 to 16) |
|
|
| ||
Map RF Device 11 to | 626 | 10 | |||
Zone (1 to 16) |
|
|
| ||
Map RF Device 12 to | 627 | 11 | |||
Zone (1 to 16) |
|
|
| ||
Map RF Device 13 to | 628 | 12 | |||
Zone (1 to 16) |
|
|
| ||
Map RF Device 14 to | 629 | 13 | |||
Zone (1 to 16) |
|
|
| ||
Map RF Device 15 to | 630 | 14 | |||
Zone (1 to 16) |
|
|
| ||
Map RF Device 16 to | 631 | 15 | |||
Zone (1 to 16) |
|
|
| ||
|
|
|
| ||
| Mapping RF device to zone |
| |||
*The programming for zone numbers 9 through 16 is in hexadecimal code (00 through 15).
These locations allow you to map RF wireless control panel. You cannot map more than one RF wireless device to the same zone. Refer to Section 20.3 to map RF wireless devices 1 to 8.
By default, RF devices 9 through 16 are mapped separately to each of the eight zones (that is, Device 9 is mapped to Zone 9, Device 10 to Zone 10). Locations 616 to 623 and locations 624 to 631 can be programmed as any value from 00 to 15. Refer to Section 20.5 Using Hexadecimal Values for RF Device Mapping on page 89 for mapping information.
20.5Using Hexadecimal Values for RF Device Mapping
To map an RF device, first select a device number and enable the device. Refer to Section 20.2 RF Device Mapping Option on page 89.
Bosch Security Systems, Inc. 12/08
