Bosch Appliances ICP-CC488 manual 21.3 SS914 Edmsat Satellite Siren, 21.4 CC891 Programming Key

ICP-CC488 Installation Guide 21.0 Optional Equipment

EN 91

21.3SS914 EDMSAT Satellite Siren

The EDMSAT Satellite Siren is a totally self- contained unit incorporating a high-powered siren and a weatherproof strobe. A 1.2 Ah sealed lead-acid battery must be installed. The EDMSAT requires only two wires, which enable charging of the battery and activating of the siren and strobe. This is accomplished by pulse code modulating (PCM) the charging voltage. Any attempt to tamper with the wiring or to substitute an alternate power source across the wiring disrupts the data transmission and activates the EDMSAT immediately. When the EDMSAT executes a battery test, the unit sounds for 2 sec if the battery test fails. Use Output Event Type 0,0 EDMSAT - Satellite Siren (refer to page 71) when programming an output for the satellite siren.

21.4CC891 Programming Key

The programming key copies and stores all information programmed in your control panel. The programming key can hold all your common configuration data such as monitoring station telephone numbers and zone reporting channels.

21.5CC816 Alarm Link Software

This software package is designed to program the ICP-CC488 Control Panel by either the direct link or remote connect methods. This software can access all options and features and maintain history and service reports. Program options to use this feature in Location 180. Refer to Section 8.0 Alarm Link Software on page 40 for more information on using Alarm Link software.

21.6ICP-CP508W Eight Zone LED Codepad

This codepad operates with the control panels. It provides indications for up to eight zones. This codepad cannot be used with the ICP-CC488 Control Panel.

21.7ICP-CP508LW Eight Zone LCD Codepad

This codepad operates with the ICP-CC488 control panels. This codepad has a fixed icon display and provides indications for up to eight zones. This codepad cannot be used with the ICP-CC488 Control Panel.

21.8ICP-CP500AW Eight Zone Area Addressable Codepad

This codepad operates with a partitioned ICP-CC488 Control Panel. This codepad has a DIP switch on the back to select the area to which the codepad belongs. Refer to Section 19.6 Setting Up and Programming Codepads for Partitioning and Section 19.7 Codepad Connections For Partitioning for more information.

21.9ICP-CP500PW Master Partitioned Codepad

This codepad operates with a partitioned ICP-CC488 Control Panel. This codepad enables you to operate the entire system from a single codepad by toggling between the two areas by pressing [AWAY]. With this codepad, it is not necessary to have separate CP5 Area Addressable (CP500A) codepads for each area. Refer to Section 19.6 Setting Up and Programming Codepads for Partitioning and Section 19.7 Codepad Connections For Partitioning for more information.

21.10 CP105 Night Arm Station

The night arm station incorporates a panic button and allows the user to arm and disarm the system in STAY Mode 1 from a bedroom or sitting room. Enable the night arm station to operate with the system by selecting Option 8 in Location 495 (refer to Section 18.4 System Options 4).

21.11 TF008 Plug Pack (TF008)

The TF008 plug pack is used with control panels. The plug pack includes built-in thermal fuses that blow during overload or fault conditions to eliminate a possible fire threat due to excessive heat buildup inside the casing.

The plug pack incorporates a three-wire flying lead that enables a MAINS earth connection between the equipment and the plug pack. This connection might be required for lightning protection on equipment connected to phone lines or for safety reasons such as earthing of metal enclosures.

Bosch Security Systems, Inc. 12/08 F01U089457-02