EPSON Stylus Pro 7600/9600

Revision A

1.4.3.31 User Paper Setting

Selecting this mode allows detection of the thickness of the available paper, and registration of up to four user-defined paper.

Paper feeding adjustment, ink drying time, cutting method, MW print adjustment and suction may be registered for each paper format.

†Setting

1.Select user paper setting menu from the panel.

2.Select the paper number (‘STD’, ‘1’~‘10’)

3.Print the paper thickness detection pattern.

4.Check the printed adjustment patterns and enter the number of the pattern with the least displacement for each adjustment item. (See p.58)

Table 1-38. Relationship between Pattern Numbers and Paper Thickness

Number

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Paper

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

0.9

1.0

1.1

1.2

1.3

1.4

1.5

1.6

thickness

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.Enter cutting pressure.

6.Select cutting method.

7.Enter the paper feeding adjustment value.

8.Enter the ink dying time for each pass.

9.Select paper suction.

10.Select MW print quality adjustment.

NOTE 1: Paper setting can be made independently for any paper number.

2:For details of patterns, refer to Print paper thickness detection pattern (p. 58)”.

Paper setting and corresponding operation are as follows.

 

Table 1-39.

 

 

Paper setup

Operation

 

 

Standard

When settings of cutting pressure ~ print quality are set with

 

commands, it follows the settings.

 

 

1 ~ 10

User definition paper. Even when cutting pressure ~ print quality are

 

set with commands, user setting value is used.

 

 

Details of each setting item are following;

 

Table 1-40.

 

 

Setting

Operation

 

 

Paper thickness

Print paper thickness detection pattern and enter the paper thickness

 

number. (When “STD” is selected, it is not executed.) *1

Cutting pressure

Paper cutting pressure is set. Lower the pressure for thin and soft

 

paper. Manufacture setting value (75%) is displayed as 100%, which is

 

the maximum setting value to be assured. Setting available range is

 

110%~0%.

Cutting method

Cutting method is selected, 4 step cutting for thin and soft paper. Paper

 

feed adjustment Paper feeding is adjusted. When 0.00% is not selected

 

for paper feed adjustment, it ignores driver command (SN 03H 00H

 

00H 04H m2) and setting value with SN menu of Maintenance mode1,

 

and uses this setting value.

 

 

Ink drying time

Ink drying time for each pass is set.- The carriage stops at the right/left

 

sides of paper for setting time.

Paper suction

Paper suction is set to make paper stable on the platen. Select “LOW”

 

for thin paper (film), which is difficult to feed.

 

 

MW print adjustment

Micro weave mode is adjusted. When print speed has priority, lower

 

the setting value. When quality has priority, raise the setting value.*2

Note 1: When “STD” is selected for Paper selection, Paper thickness detection pattern print, Paper thickness number selection, Paper feeding adjustment setting items are not displayed. Only when Paper “1” ~ “10” is selected, they are displayed.

2:During pattern printing, “PRINTING ALGNMNT PATTERN” is displayed. (<\n> is new line)

3:Default display of paper thickness number selection is the number same as gap adjustment.

Note *1: See “MW Printing Adjustment / Setting Values and Printing Modes (p.88)” for selectable MW mode at MW print adjustment.

*2: It prints with PG small or PG big depending on detection result of paper thickness sensor.

Product Description

Operating Panel

56

Page 56
Image 56
Epson 9600, 7600 User Paper Setting, Paper setting and corresponding operation are as follows, Paper setup Operation