Icom IC-7000 instruction manual Control Command

17 CONTROL COMMAND

•Command table (continued)

Command	Sub command	Description
0E	B0	Set as non-select channel
	B1	Set as select channel
	D0	Set scan resume OFF
	D3	Set scan resume ON
0F	00	Turn the split function OFF
	01	Turn the split function ON
	10	Select simplex operation
	11	Select –DUP operation
	12	Select +DUP operation
10	00	AM/FM/WFM modes:
		Select 10 Hz (1 Hz) tuning step
		SSB/CW/RTTY modes: TS OFF
	01	Select 100 Hz tuning step
	02	Select 1 kHz tuning step
	03	Select 5 kHz tuning step
	04	Select 9 kHz tuning step
	05	Select 10 kHz tuning step
	06	Select 12.5 kHz tuning step
	07	Select 20 kHz tuning step
	08	Select 25 kHz tuning step
	09	Select 100 kHz tuning step
	10	AM/FM/WFM modes:
		Select MHz step
		SSB/CW/RTTY modes: TS OFF
11	—	Select/read attenuator (0=OFF,
		12=ON (12 dB))
13	00	Announce with voice synthesizer
	01	(00=all data; 01=frequency and
	02	S-meter level; 02=receive mode)

1401 + Level data [AF] level setting (0=max. CCW to 255=max. CW)

02 + Level data [RF] level setting (0=max. CCW to

255=11 o’clock)

03 + Level data [SQL] level setting (0=11 o’clock to 255=max. CW)

06 + Level data	NR level setting (0=min. to
	255=max.)
07 + Level data	Inside [PBT] setting or IF shift
	setting (0=max. CCW, 128=cen-
	ter, 255=max. CW)
08 + Level data	Outside [PBT] setting
	(0=max. CCW, 128=center,
	255=max. CW)
09 + Level data	CW Pitch setting (0=300 Hz,
	128=600 Hz, 255=900 Hz, in 5 Hz
	steps)
0A + Level data	RF Power setting (0=mini. to
	255=max.)
0B + Level data	MIC Gain setting (0=mini. to
	255=max.)
0C + Level data	Key Speed setting (0=slow to
	255=fast)
0D + Level data	NOTCH (NF1) frequency setting
	(0=low freq. to 255=high freq.)
0E + Level data	COMP Level setting (0=0 to
	10=10)
0F + Level data	Break-IN DELAY setting (20=2.0d
	to 130=13.0d)
12 + Level data	NB level setting (0=0 to
	255=100%)
15 + Level data	Monitor gain setting (0=0 to
	255=100%)
16 + Level data	VOX gain setting (0=0 to
	255=100%)

Command Sub command Description

1417 + Level data Anti-VOX gain setting (0=0 to 255=100%)

	18 + Level data	Contrast (LCD) setting (0=0 to
		255=100%)
	19 + Level data	Bright (LCD) setting (0=0 to
		255=100%)
	1A + Level data	NOTCH (NF2) frequency setting
		(0=low freq. to 255=high freq.)
15	01	Read squelch condition
	02	Read S-meter level
	11	Read RF power meter
	12	Read SWR meter
	13	Read ALC meter
	14	Read COMP meter
16	02	Preamp (0=OFF; 1=ON)
	12	AGC selection (0=OFF; 1=Slow;
		2=Mid; 3=Fast)
	22	Noise blanker (0=OFF; 1=ON)
	40	Noise reduction (0=OFF; 1=ON)
	41	Auto notch (0=OFF; 1=ON)
	42	Repeater tone (0=OFF; 1=ON)
	43	Tone squelch (0=OFF; 1=ON)
	44	Speech compressor (0=OFF; 1=ON)
	45	Monitor (0=OFF; 1=ON)
	46	VOX function (0=OFF; 1=ON)
	47	Break-in (0=OFF; 1=semi break-
		in; 2=full break-in)
	48	Manual notch (NF1) (0=OFF; 1=ON)
	4B	DTCS (0=OFF; 1=ON)
	4C	VSC (0=OFF; 1=ON)
	4F	Twin Peak Filter (0=OFF; 1=ON)
	50	Dial lock function (0=OFF, 1=ON)
	51	Manual notch (NF2) (0=OFF, 1=ON)
19	00	Read the transceiver ID
1A	00	Send/read memory contents (see
		p. 148 for details)
	01	Send/read band stacking register
		contents (see p. 148 for details)
	02	Send/read memory keyer contents
		(see p. 148 for details)
	03	Send/read the selected filter width
		(SSB, CW, RTTY: 0=50 Hz to
		31=2700 Hz; AM: 0=200 Hz to
		49=10 kHz)
	04	Send/read the selected AGC time
		constant (0=OFF, 1=0.1/0.3 sec. to
		13=6.0/8.0 sec.)
	050001	RF Power setting (0=mini. to
		255=max.)
	050002	MIC Gain setting (0=mini. to
		255=max.)
	050003	Send/read of SSB TX bandwidth
		(lower edge) for wide
		(0=100, 1=200, 2=300, 3=500 HZ)
	050004	Send/read of SSB TX bandwidth
		(higher edge) for wide (0=2500,
		1=2700, 2=2800, 3=2900 HZ)
	050005	Send/read of SSB TX bandwidth
		(lower edge) for middle
		(0=100, 1=200, 2=300, 3=500 HZ)
	050006	Send/read of SSB TX bandwidth
		(higher edge) for middle (0=2500,
		1=2700, 2=2800, 3=2900 HZ)

145