Manuals / Icom / Marine Equipment / Marine Radio

Icom IC-7000 instruction manual Miscellaneous others set mode

Models: IC-7000

1 166

Download 166 pages 46.93 Kb

Page 139

SET MODE 13

■Miscellaneous (others) set mode

1Monitor

This item sets the TX monitor function ON and OFF.

The monitor gain can be set described below.

ON	OFF
TX monitor	function is TX monitor function is
turned ON.	turned OFF. (default)

2 Monitor Level

This item adjusts the transmit IF signal monitor level

from 0% to 100% in 1% steps.

50%

50% (default)

See p. 89 for details.

3 Beep(Confirmation)

	A beep sounds each time a switch is pushed to con-	ON	OFF
	ﬁrm it. This function can be turned OFF for silent op-	Conﬁrmation beep ON	Conﬁrmation beep OFF
	eration.	Conﬁrmation beep ON	Conﬁrmation beep OFF
	eration.	(default)
	The volume level can be set described below.

4 Beep(Band Edge)

	A beep sounds when an operating frequency enters	ON	OFF
	or exits an amateur band. This functions independent	Band edge beep ON	Band edge beep OFF
	of the conﬁrmation beep setting (above).	Band edge beep ON	Band edge beep OFF
	of the conﬁrmation beep setting (above).	(default)
	The volume level can be set described below.

	5 Beep Level
	This item adjusts the volume level for (confirmation
	and band edge) beep tones from 0% to 100% in 1%					50%
	steps. When beep tones are turned OFF, this setting					50%
	steps. When beep tones are turned OFF, this setting			50% (default)
	has no effect.			50% (default)
	has no effect.

13

6 Beep Level Limit

This item allows you to set a maximum volume level for (confirmation and band edge) beep tones. The beep tones are linked to the [AF] control until a spec- iﬁed volume level is reached — further rotation of the [AF] control will not increase the volume of the beep tones.

ON	OFF
Beep level is limited with	Beep level is linked to [AF]
[AF] (default)

130

Image 139

Icom IC-7000 instruction manual Miscellaneous others set mode

Contents

I7000 Risk or personal injury, fire or electric Word Definition RwarningShock may occur Equipment damage may occurIllustrations Microphone HM-151 7MAIN Dial Dial 8RECEIVE/TRANSMIT Indicators RX/TXPower Indicator Programmable Function Keys F-1/F-2 Front panelPrecautions Table of Contents NR Level …………………………………… Transmit ﬁlter width setting SSB only ………Hz tone burst ……………………………… SSB/CW/RTTY/AM only ……………………From the TNC ………………………………… Operation………………………………………… AH-4 operation ………………………………General ………………………………………… Transmitter……………………………………… Specifications …………………………Panel Description TUNER/CALL KEY TUNER/CALL Twin PBT M-ch/RIT Indicator Pgs , 79, 88Panel Description MENU/GROUP Keys MENU/GRP p7MAIN Dial Dial 1AUTO NOTCH/VOICE Recorder KEY ANF/ REC2SPCH/LOCK KEY SPCH/LOCK 4UP/DOWN Band Keys YBAND/ZBAND@2FUNCTION Display 9TUNING Step KEY TS pgsMenu M-3 functions Multi-function keysMenu M-1 functions Menu M-2 functionsFM Tone Operation FunctionSelect Scan Menu S-1 functionsMenu S-2 functions Dtmf OperationMenu G-1 Scope functions Menu S-3 functionsSweep Speed ⁄3TUNER/CALL KEY TUNER/CALL Power Indicator⁄1VFO/MEMORY Selection V/M ⁄2TRANSMIT Frequency Check XFCMicrophone Connector Information Microphone connectorRear panel ACC socket Data socketMeter Readouts When connecting the ACC conversion cable OPC-599Function display Frequency Readout7MULTI-FUNCTION Screen Appears when the preamp is onAppears when the 12 dB attenuator is @01/4 Function IndicatorAntenna connection Installation and ConnectionsUnpacking Selecting a locationFront panel mounting InstallationStand Front panel separationHM-151 Required connectionsGround p Used for computer control and transceive Operation Advanced connectionsSpea KER p Remot E p 4 pConnecting a DC power supply Power supply connectionsBattery connections External antenna tuners Connecting the AH-4OPC-599 conversion cable Connecting the IC-PW1/EUROLinear ampliﬁer connections MHz linear ampliﬁerFor no break-in operation Connections for CWACC Rtty EXT SP Connections for packet When connecting to Data socketWhen connecting to ACC socket When connecting to MIC connectorBasic Operation When ﬁrst applying power CPU resettingInitial settings Menu resetting M-1Example Differences between VFO and memory modeVFO Mode VFO descriptionVFO equalization Selecting VFO/memory modeVFO operation Selecting VFO A/VFO BSelecting an operating band Using the band stacking registersBand Register Push F-INP/ENT Frequency settingTuning with the main dial Direct frequency entry with the microphone’s keypadSelecting kHz step Programmable tuning stepRotate Dial for normal tuning, if desired Push TS momentarily to turn the programmable tuning step onSelecting 1 Hz or 10 Hz step SSB/CW/RTTY only MHz quick tuning step FM/WFM/AM onlySelect M-3 ⁄4 tuning function CW/RTTY onlyPush ZMENU/GRP twice to return the normal op- erating mode Volume settingAuto tuning step function Push ZMENU/GRP twice to return to the normal operating modeVoice synthesizer function Operating mode selectionSquelch and receive RF sensitivity Setting OperationWhen setting as RF gain/squelch control When functioning as squelch control RF gain isSelect S-1 Meter functionMulti-function meter Quick entryMicrophone lock function Lock functionsBasic transmit operation Dial lock functionSetting microphone gain Setting output powerBand SSB/CW Operating SSB Receive and TransmitConvenient functions for receive Transmit quality monitor p IC-7000 Tuning FCC ChannelConvenient functions for transmit About 5 MHz band operation USA version onlyOperating CW Set CW setting in the keyer set mode S-10Stop keying to return to receive While M-3 is selected, push F-1BRK one or Push P.AMP/ATT momentarily to turn the pre- amp on or OFF⁄4 function p Break-in function p Memory keyer function pPush ZMENU/GRP to exit the quick set mode CW reverse modeCW side tone function CW pitch control Electronic CW keyer Memory keyer send menu Pre-set characters can be sent using the memorySelect S-1 Push F-2KEY to enter the keyer send menu DEditing a keyer memory Programming contentsCount UP Trigger Contest number set modeSetting the contact serial number Number StyleDot/Dash Ratio Keyer set modeSetting the electronic keyer Keyer Repeat TimeKeyer Type Keyer set mode Rise TimePaddle operation from MIC connector Paddle PolarityRotate Dial to simultaneously tune a desired sig- nal Transmit a Send signal from your TNCOperating Rtty FSK Display the Rtty decoder screenConvenient functions for receive Twin peak ﬁlter Rtty reverse modeMode Function for the Rtty decoder indication Setting the decoder threshold levelRtty Decode Usos Rtty decode set modeRtty Decode New Line Code Shift width Pre-setting for using Rtty terminal or TNCMark frequency Rotate Dial to select the desired frequencyOperating AM Push NR/LEV to turn the DSP noise reduction DSP noise reduction p Auto notch ﬁlter pWhile M-3 is selected, push F-1 VOX to turn Operating FMPreamp and attenuator p DSP noise reduction p Amp on or OFF On and OFFRotate Dial to set the desired subaudible tone frequency Push Mode one or more times to select FM mode Select M-3Push F-3TON for 1 sec. to enter the FM tone set mode Tone squelch operationTone scan operation Push ZMENU/GRP to exit the FM tone set modePush F-3TON once or twice to turn the Dtcs function on Dtcs operationAvailable tone codes One-touch repeater function Repeater operationPush F-3TON to turn the repeater tone on Push F-3TON once or twice to turn the tone en- coder on Repeater tone frequencyAuto repeater function Transmit frequency monitor checkFrequency range and offset direction Turn the auto repeater function OFF in the miscel Storing a non standard repeaterSelect M-2 Dtmf send menu Dtmf memory encoderPush F-2DTM then ZMENU/GRP to select the Dtmf root menu Push Mode to select FM mode. w Select S-1Programming a Dtmf code Dtmf speedRotate AF to set a suitable audio level Push and hold Afset for 1 sec. to turn the TV mode onTV channel operation Rotate M-chinner control to select the desired TV channelSkip channel setting Push F-3SET to set the channel frequency Channel frequency adjustmentRotate Dial to adjust the channel frequency Push ZMENU/GRP to exit the channel frequency set modeFunctions for Receive Fix modeSimple band scope Select G-1 Scope Center modeScope set mode Push F-3FIX momentarily to select the center modeFast Sweep Preamp and attenuatorMax Hold Scope SizeCalculate function To reset the RIT frequency, push F-3CLR for 1 secTo cancel the RIT function, push F-1RIT mo- mentarily again RIT functionSelectable AGC time constant unit sec Setting the AGC time constantAGC function AGC time constant selectionSelect the desired mode. w Select M-1 If ﬁlter for WFM mode is ﬁxed and cannot be changedIf ﬁlter selection If ﬁlter selectionIf fIlter shape SSB/CW only FIlter passband width setting SSB/CW/RTTY/AM onlySelect SSB, CW, Rtty or AM mode Push F-3FIL for 1 sec. to enter ﬁlter set modePBT Operation Example Twin PBT operationNB Width Noise blanker set modeNoise blanker NB LevelNoise reduction Noise reduction set modeNR Level This transceiver has auto and manual notch func Mode While in CW and Rtty modes, push MNF/ADJNotch function Auto notch functionManual notch function Manual notch ﬁlter set modePush ZMENU/GRP twice to return to normal op Erating modeVoice squelch control function Meter peak hold functionFunctions for Transmit Adjusting the VOX functionVOX function Anti-VOX Transmit ﬁlter width setting SSB onlyVOX set mode VOX Gain VOX DelayFull break-in operation Break-in delay settingBreak-in function Semi break-in operationRotate RIT outer control to shift the transmitter frequency To reset the ∂TX frequency, push F-3CLR for 1 secTo cancel the ∂TX function, push F-2∂TX mo- mentarily again ∂TX functionSpeech compressor Monitor functionPush F-3MET one or more times to select the Comp meter Compression level settingComp Level Select Comp meter Select S-1Push F-1SPL M-1 on the transceiver’s front panel Split frequency operationSelect VFO a and set the frequency to 21.290 MHz USB Direct Shift Frequency InputMenu selection Example M-1 Quick split functionPush F-INP/ENT,, 5 then F-1 SPL M-1 Rotate Dial to set the desired split offset Split offset frequency settingQuick split setting Erating modePlot measurement Measuring SWRMenu selection Example S-1 Spot measurementBasic recording Voice Recorder FunctionsDigital voice recorder Recording a received audioPlaying the recorded contents Erasing the recorded contents Push ZMENU/GRP twice to exit the voice mem- ory screen Recording a message for transmitRecording Push F-3REC again to stop recordingPush ZMENU/GRP to input and set the name Programming a memory name for transmitSpaces can be used. See the step t below Input the desired character by rotating DialPush F-1T1 F-4T4 to transmit the con- tents Transmit level settingSending a recorded message Select S-1 Push F-1VO to call up the voice recorder menuVoice set mode Auto Monitor Voice set modeMIC Memo Memory Transfer Over Channel Capability Clear Memory OperationMemory channels Memory channel selectionRotate M-chto select the desired memory chan- nel Programming in VFO modeSet the desired frequency and operating mode in VFO mode Memory programmingSet the desired frequency and operating mode Programming in memory modeMemory channel list Selecting a memory channel using the memory channel listSelecting a memory bank Setting a memory channel as a select memoryMemory channel list indication Editing programming memory names Memory namesMemory clearing Memory clearing using the memory channel listTo return to VFO mode, push F-4V/M again Frequency transferring Transferring in VFO modeSelect a memory channel with M-ch Push F-4V/M momentarily to select the VFO mode Transferring in memory modeWriting frequencies and operating modes into memo pads Memo padsCalling up a frequency from a memo pad Scan types Scan OperationPreparation Memory scan operation Programmed scan operationPriority watch Select memory scan operationTuner operation Manual tuningAntenna Tuner Operation Optional AT-180 Automatic Antenna Tuner operationPTT tune function AH-4 operationPacket operation Adjusting the data speedAdjusting the transmit signal output from the TNC Packet OperationTime set mode Clock and TimersSetting the current date Setting the current yearSetting the current time Push ZMENU/GRP twice to exit timer set mode Clock2 offset settingAuto power OFF activity Set the desired power-off time using DialSet mode description SET ModeRF Power all modes Quick set modeSSB TBW Wide L SSB mode Mode Set mode item Default setting RF PowerSSB TBW NAR L SSB mode SSB TBW Wide H SSB modeSSB TBW MID L SSB mode SSB TBW MID H SSB modeRtty Mark Frequency Rtty mode Side Tone Level CW modeSide Tone Level Limit CW mode Twin Peak Filter Rtty modeDisplay set mode Meter Peak Hold 12 1Hz Mode PopupDisplay Font Type Display Font SizeKeyer Memory Display TV Popup CH Up/DownTV Popup P.AMP/ATT Voice TX Name DisplayOpening screen example Power on CheckPush ZMENU/GRP twice to exit the set mode screen My CallMiscellaneous others set mode DUP Offset HF RF/SQL ControlQuick Split Split OffsetAuto Repeater DUP Offset 144MDUP Offset 430M One Touch RepeaterSpeech Level Tuner SwitchTuner PTT Start Vsend SelectScan Speed Speech Mode SwitchSpeech S-Level Memopad NumbersMIC Up/Down Speed 34 SSB/CW Synchronous Tuning30 HM-151 F-1 31 HM-151 F-2CW Normal Side Mode Select SSBMode Select CW Mode Select RttyExternal Keypad Voice Mode Select AMMode Select FM Mode Select WFMCI-V Address REF AdjustFront Keypad Type CI-V Baud RateCleaning MaintenanceFuse replacement Memory backupEst Icom Dealer or Service Center TroubleshootingTransmit Display Scan Problem Possible Cause Solution MB-106CARRYING Handle Option Units SettingSpeciﬁcations for the AT-180 AT-180 internal switch descriptionConnector information for ACC2 socket AT-180 inside top coverCI-V connection example Control CommandCommand table Remote jack CI-V informationControl Command 146 147 Codes for memory keyer contents To send/read memory contentsBand stacking register Dtcs code and polarity setting Codes for memory name contentsSplit/Duplex frequency setting Repeater tone/tone squelch frequency SettingGeneral SpecificationsMB-62 OptionsOPC-1444 OPC-1443OPC-589 Main menu group Sub menu group Menu GuideGraphic menu group Set mode description Memo Memo Intended Country of Use