Frequency setting, Tuning with the main dial | Icom IC-7000 specs

3BASIC OPERATION

■Frequency setting

The transceiver has several tuning methods for conve- nient frequency tuning.

DTuning with the main dial

[Y]

[Z]

							[DIAL]
HM-151
SPCH			TUNER			XFC
	/LOCK /CALL					XFC
				V/M		MW
				F-1		F-2
				F-1
1.8 1		3.5 2		7	3	MODE
10 4		14 5		18 6		FIL	Band keys
21	7	24	8	28	9	GENE	Band keys
50 .		144		430		F-INP
			0		CE	ENT

q Push [Y(BAND)] or [Z(BAND)] to select the desired band. Or push the desired band key on the micro- phone 1–3 times.

•Three different frequencies can be selected on each band with the microphone’s band key. (See previous page “Using the band stacking register.”)

w Rotate [DIAL] to set the desired frequency.

If the dial lock function is activated, “ ” indicator

lights, and [DIAL] does not function. In this case,

push [SPCH/LOCK] to deactivate the lock func- tion. (p. 37)

DDirect frequency entry with the microphone’s keypad

The HM-151 has a keypad for direct frequency entry as described right.

HM-151

SPCH			TUNER			XFC
	/LOCK		/CALL			XFC
				V/M		MW
				F-1		F-2
				F-1
1.8 1		3.5 2		7	3	MODE
10 4		14 5		18 6		FIL
21 7		24 8		28 9		GENE	Keypad
	.		0		CE	ENT	Keypad
50		144		430		F-INP

q Push [F-INP/ENT].

•“ ” appears.

w Input the desired frequency.

•Push [(50)•] to input “ • (decimal point)” between the MHz digits and kHz digits.

e Push [F-INP/ENT]to set the input frequency.

•To cancel the input, push [CE] instead of [F-INP/ENT].

[EXAMPLES] 14.025 MHz

F-INP	1.8	1	10	4	50	.	144	0	3.5	2	14	5	F-INP
ENT													ENT
18.0725 MHz
F-INP	1.8	1	24	8	50	.	144	0	21	7	3.5	2	14	5	F-INP
ENT															ENT
706 kHz			F-INP		144	0	50	.	21	7	144	0	18	6	F-INP
			ENT												ENT
5.100 MHz					F-INP		14	5	50	.	1.8	1	F-INP
					ENT								ENT
7.000 MHz					F-INP		21	7	F-INP
					ENT				ENT
21.280	21.245				F-INP		50	.	3.5	2	10	4	14	5	F-INP
					ENT										ENT

29

Image 38

Icom IC-7000 Frequency setting, Tuning with the main dial, Direct frequency entry with the microphone’s keypad

Contents

I7000 Equipment damage may occur Word Definition RwarningShock may occur Risk or personal injury, fire or electric Illustrations Front panel 7MAIN Dial Dial 8RECEIVE/TRANSMIT Indicators RX/TXPower Indicator Programmable Function Keys F-1/F-2 Microphone HM-151 Precautions Table of Contents SSB/CW/RTTY/AM only …………………… Transmit ﬁlter width setting SSB only ………Hz tone burst ……………………………… NR Level …………………………………… Operation………………………………………… AH-4 operation ……………………………… From the TNC ………………………………… Specifications ………………………… General ………………………………………… Transmitter……………………………………… Panel Description MENU/GROUP Keys MENU/GRP p Twin PBT M-ch/RIT Indicator Pgs , 79, 88Panel Description TUNER/CALL KEY TUNER/CALL 4UP/DOWN Band Keys YBAND/ZBAND 1AUTO NOTCH/VOICE Recorder KEY ANF/ REC2SPCH/LOCK KEY SPCH/LOCK 7MAIN Dial Dial 9TUNING Step KEY TS pgs @2FUNCTION Display Menu M-2 functions Multi-function keysMenu M-1 functions Menu M-3 functions Function FM Tone Operation Dtmf Operation Menu S-1 functionsMenu S-2 functions Select Scan Sweep Speed Menu S-3 functionsMenu G-1 Scope functions ⁄2TRANSMIT Frequency Check XFC Power Indicator⁄1VFO/MEMORY Selection V/M ⁄3TUNER/CALL KEY TUNER/CALL Microphone connector Microphone Connector Information Rear panel Data socket ACC socket Frequency Readout When connecting the ACC conversion cable OPC-599Function display Meter Readouts @01/4 Function Indicator Appears when the preamp is onAppears when the 12 dB attenuator is 7MULTI-FUNCTION Screen Selecting a location Installation and ConnectionsUnpacking Antenna connection Front panel separation InstallationStand Front panel mounting Ground p Required connectionsHM-151 Remot E p 4 p Advanced connectionsSpea KER p Used for computer control and transceive Operation Battery connections Power supply connectionsConnecting a DC power supply Connecting the AH-4 External antenna tuners MHz linear ampliﬁer Connecting the IC-PW1/EUROLinear ampliﬁer connections OPC-599 conversion cable Connections for CW For no break-in operation ACC Rtty EXT SP When connecting to MIC connector When connecting to Data socketWhen connecting to ACC socket Connections for packet Menu resetting M-1 When ﬁrst applying power CPU resettingInitial settings Basic Operation VFO description Differences between VFO and memory modeVFO Mode Example Selecting VFO A/VFO B Selecting VFO/memory modeVFO operation VFO equalization Band Register Using the band stacking registersSelecting an operating band Direct frequency entry with the microphone’s keypad Frequency settingTuning with the main dial Push F-INP/ENT Push TS momentarily to turn the programmable tuning step on Programmable tuning stepRotate Dial for normal tuning, if desired Selecting kHz step MHz quick tuning step FM/WFM/AM only Selecting 1 Hz or 10 Hz step SSB/CW/RTTY only ⁄4 tuning function CW/RTTY only Select M-3 Push ZMENU/GRP twice to return to the normal operating mode Volume settingAuto tuning step function Push ZMENU/GRP twice to return the normal op- erating mode Operating mode selection Voice synthesizer function When functioning as squelch control RF gain is Setting OperationWhen setting as RF gain/squelch control Squelch and receive RF sensitivity Quick entry Meter functionMulti-function meter Select S-1 Dial lock function Lock functionsBasic transmit operation Microphone lock function Band SSB/CW Setting output powerSetting microphone gain Convenient functions for receive Receive and TransmitOperating SSB About 5 MHz band operation USA version only IC-7000 Tuning FCC ChannelConvenient functions for transmit Transmit quality monitor p 0Stop keying to return to receive Set CW setting in the keyer set mode S-1Operating CW Break-in function p Memory keyer function p Push P.AMP/ATT momentarily to turn the pre- amp on or OFF⁄4 function p While M-3 is selected, push F-1BRK one or CW side tone function CW reverse modePush ZMENU/GRP to exit the quick set mode CW pitch control Electronic CW keyer Select S-1 Push F-2KEY to enter the keyer send menu Pre-set characters can be sent using the memoryMemory keyer send menu Programming contents DEditing a keyer memory Number Style Contest number set modeSetting the contact serial number Count UP Trigger Keyer Repeat Time Keyer set modeSetting the electronic keyer Dot/Dash Ratio Paddle Polarity Keyer set mode Rise TimePaddle operation from MIC connector Keyer Type Display the Rtty decoder screen Transmit a Send signal from your TNCOperating Rtty FSK Rotate Dial to simultaneously tune a desired sig- nal Convenient functions for receive Mode Rtty reverse modeTwin peak ﬁlter Setting the decoder threshold level Function for the Rtty decoder indication Rtty Decode New Line Code Rtty decode set modeRtty Decode Usos Rotate Dial to select the desired frequency Pre-setting for using Rtty terminal or TNCMark frequency Shift width Operating AM DSP noise reduction p Auto notch ﬁlter p Push NR/LEV to turn the DSP noise reduction Amp on or OFF On and OFF Operating FMPreamp and attenuator p DSP noise reduction p While M-3 is selected, push F-1 VOX to turn Tone squelch operation Push Mode one or more times to select FM mode Select M-3Push F-3TON for 1 sec. to enter the FM tone set mode Rotate Dial to set the desired subaudible tone frequency Push ZMENU/GRP to exit the FM tone set mode Tone scan operation Available tone codes Dtcs operationPush F-3TON once or twice to turn the Dtcs function on Push F-3TON to turn the repeater tone on Repeater operationOne-touch repeater function Repeater tone frequency Push F-3TON once or twice to turn the tone en- coder on Frequency range and offset direction Transmit frequency monitor checkAuto repeater function Select M-2 Storing a non standard repeaterTurn the auto repeater function OFF in the miscel Dtmf memory encoder Dtmf send menu Dtmf speed Push Mode to select FM mode. w Select S-1Programming a Dtmf code Push F-2DTM then ZMENU/GRP to select the Dtmf root menu Rotate M-chinner control to select the desired TV channel Push and hold Afset for 1 sec. to turn the TV mode onTV channel operation Rotate AF to set a suitable audio level Skip channel setting Push ZMENU/GRP to exit the channel frequency set mode Channel frequency adjustmentRotate Dial to adjust the channel frequency Push F-3SET to set the channel frequency Simple band scope Fix modeFunctions for Receive Push F-3FIX momentarily to select the center mode Center modeScope set mode Select G-1 Scope Scope Size Preamp and attenuatorMax Hold Fast Sweep RIT function To reset the RIT frequency, push F-3CLR for 1 secTo cancel the RIT function, push F-1RIT mo- mentarily again Calculate function AGC time constant selection Setting the AGC time constantAGC function Selectable AGC time constant unit sec If ﬁlter selection If ﬁlter for WFM mode is ﬁxed and cannot be changedIf ﬁlter selection Select the desired mode. w Select M-1 Push F-3FIL for 1 sec. to enter ﬁlter set mode FIlter passband width setting SSB/CW/RTTY/AM onlySelect SSB, CW, Rtty or AM mode If fIlter shape SSB/CW only Twin PBT operation PBT Operation Example NB Level Noise blanker set modeNoise blanker NB Width NR Level Noise reduction set modeNoise reduction Auto notch function Mode While in CW and Rtty modes, push MNF/ADJNotch function This transceiver has auto and manual notch func Manual notch ﬁlter set mode Manual notch function Meter peak hold function Erating modeVoice squelch control function Push ZMENU/GRP twice to return to normal op VOX function Adjusting the VOX functionFunctions for Transmit VOX Delay Transmit ﬁlter width setting SSB onlyVOX set mode VOX Gain Anti-VOX Semi break-in operation Break-in delay settingBreak-in function Full break-in operation ∂TX function To reset the ∂TX frequency, push F-3CLR for 1 secTo cancel the ∂TX function, push F-2∂TX mo- mentarily again Rotate RIT outer control to shift the transmitter frequency Monitor function Speech compressor Select Comp meter Select S-1 Compression level settingComp Level Push F-3MET one or more times to select the Comp meter Direct Shift Frequency Input Split frequency operationSelect VFO a and set the frequency to 21.290 MHz USB Push F-1SPL M-1 on the transceiver’s front panel Push F-INP/ENT,, 5 then F-1 SPL M-1 Quick split functionMenu selection Example M-1 Erating mode Split offset frequency settingQuick split setting Rotate Dial to set the desired split offset Spot measurement Measuring SWRMenu selection Example S-1 Plot measurement Recording a received audio Voice Recorder FunctionsDigital voice recorder Basic recording Playing the recorded contents Erasing the recorded contents Push F-3REC again to stop recording Recording a message for transmitRecording Push ZMENU/GRP twice to exit the voice mem- ory screen Input the desired character by rotating Dial Programming a memory name for transmitSpaces can be used. See the step t below Push ZMENU/GRP to input and set the name Select S-1 Push F-1VO to call up the voice recorder menu Transmit level settingSending a recorded message Push F-1T1 F-4T4 to transmit the con- tents MIC Memo Voice set modeVoice set mode Auto Monitor Memory channel selection Memory OperationMemory channels Memory Transfer Over Channel Capability Clear Memory programming Programming in VFO modeSet the desired frequency and operating mode in VFO mode Rotate M-chto select the desired memory chan- nel Programming in memory mode Set the desired frequency and operating mode Selecting a memory channel using the memory channel list Memory channel list Memory channel list indication Setting a memory channel as a select memorySelecting a memory bank Memory names Editing programming memory names To return to VFO mode, push F-4V/M again Memory clearing using the memory channel listMemory clearing Select a memory channel with M-ch Transferring in VFO modeFrequency transferring Transferring in memory mode Push F-4V/M momentarily to select the VFO mode Memo pads Writing frequencies and operating modes into memo pads Calling up a frequency from a memo pad Preparation Scan OperationScan types Programmed scan operation Memory scan operation Select memory scan operation Priority watch Optional AT-180 Automatic Antenna Tuner operation Manual tuningAntenna Tuner Operation Tuner operation AH-4 operation PTT tune function Packet Operation Adjusting the data speedAdjusting the transmit signal output from the TNC Packet operation Clock and Timers Time set mode Setting the current time Setting the current yearSetting the current date Set the desired power-off time using Dial Clock2 offset settingAuto power OFF activity Push ZMENU/GRP twice to exit timer set mode SET Mode Set mode description Mode Set mode item Default setting RF Power Quick set modeSSB TBW Wide L SSB mode RF Power all modes SSB TBW MID H SSB mode SSB TBW Wide H SSB modeSSB TBW MID L SSB mode SSB TBW NAR L SSB mode Twin Peak Filter Rtty mode Side Tone Level CW modeSide Tone Level Limit CW mode Rtty Mark Frequency Rtty mode Display set mode Display Font Size 12 1Hz Mode PopupDisplay Font Type Meter Peak Hold Voice TX Name Display TV Popup CH Up/DownTV Popup P.AMP/ATT Keyer Memory Display My Call Power on CheckPush ZMENU/GRP twice to exit the set mode screen Opening screen example Miscellaneous others set mode Split Offset RF/SQL ControlQuick Split DUP Offset HF One Touch Repeater DUP Offset 144MDUP Offset 430M Auto Repeater Vsend Select Tuner SwitchTuner PTT Start Speech Level Memopad Numbers Speech Mode SwitchSpeech S-Level Scan Speed 31 HM-151 F-2 34 SSB/CW Synchronous Tuning30 HM-151 F-1 MIC Up/Down Speed Mode Select Rtty Mode Select SSBMode Select CW CW Normal Side Mode Select WFM Mode Select AMMode Select FM External Keypad Voice CI-V Baud Rate REF AdjustFront Keypad Type CI-V Address Memory backup MaintenanceFuse replacement Cleaning Troubleshooting Est Icom Dealer or Service Center Transmit Display Scan Problem Possible Cause Solution Option Units Setting MB-106CARRYING Handle AT-180 inside top cover AT-180 internal switch descriptionConnector information for ACC2 socket Speciﬁcations for the AT-180 Remote jack CI-V information Control CommandCommand table CI-V connection example Control Command 146 147 Band stacking register To send/read memory contentsCodes for memory keyer contents Repeater tone/tone squelch frequency Setting Codes for memory name contentsSplit/Duplex frequency setting Dtcs code and polarity setting Specifications General Options MB-62 OPC-589 OPC-1443OPC-1444 Graphic menu group Menu GuideMain menu group Sub menu group Set mode description Memo Memo Intended Country of Use