Tone scan operation | Icom IC-7000 manual

4RECEIVE AND TRANSMIT

DTone scan operation

By monitoring a signal that is being transmitted on a repeater input frequency, you can determine the tone frequency necessary to access a repeater.

qDuring tone squelch, DTCS squelch or repeater

operation (“,” “” or “” is dis- played), select M-3.

	•Push and hold [MENU/GRP] for 1 sec. once or twice
	to select the menu group M.
	•Push [MENU/GRP] momentarily one or more times to	[MENU/GRP] [F-2] [F-3]
	select the menu M-3.	[MENU/GRP] [F-2] [F-3]
	select the menu M-3.

w Push [F-3TON] for 1 sec. to enter the FM tone set mode.

e Push [F-2SCN] to toggle the tone scan operation ON and OFF.

•When a matched tone or code is detected, tone scan automatically stops, the matched tone or code is dis- played and the tone or code setting is automatically ad- justed accordingly.

r Push [Z(MENU/GRP)] to exit the FM tone set mode.

During tone squelch operation.	During DTCS squelch operation.	During repeater operation.

Page 70

Image 70

Icom IC-7000 instruction manual Tone scan operation, Push ZMENU/GRP to exit the FM tone set mode

Contents

I7000 Equipment damage may occur Word Definition RwarningShock may occur Risk or personal injury, fire or electric Illustrations Front panel 7MAIN Dial Dial 8RECEIVE/TRANSMIT Indicators RX/TXPower Indicator Programmable Function Keys F-1/F-2 Microphone HM-151 Precautions Table of Contents SSB/CW/RTTY/AM only …………………… Transmit ﬁlter width setting SSB only ………Hz tone burst ……………………………… NR Level …………………………………… Operation………………………………………… AH-4 operation ……………………………… From the TNC ………………………………… Specifications ………………………… General ………………………………………… Transmitter……………………………………… Panel Description MENU/GROUP Keys MENU/GRP p Twin PBT M-ch/RIT Indicator Pgs , 79, 88Panel Description TUNER/CALL KEY TUNER/CALL 4UP/DOWN Band Keys YBAND/ZBAND 1AUTO NOTCH/VOICE Recorder KEY ANF/ REC2SPCH/LOCK KEY SPCH/LOCK 7MAIN Dial Dial 9TUNING Step KEY TS pgs @2FUNCTION Display Menu M-2 functions Multi-function keysMenu M-1 functions Menu M-3 functions Function FM Tone Operation Dtmf Operation Menu S-1 functionsMenu S-2 functions Select Scan Menu G-1 Scope functions Menu S-3 functionsSweep Speed ⁄2TRANSMIT Frequency Check XFC Power Indicator⁄1VFO/MEMORY Selection V/M ⁄3TUNER/CALL KEY TUNER/CALL Microphone connector Microphone Connector Information Rear panel Data socket ACC socket Frequency Readout When connecting the ACC conversion cable OPC-599Function display Meter Readouts @01/4 Function Indicator Appears when the preamp is onAppears when the 12 dB attenuator is 7MULTI-FUNCTION Screen Selecting a location Installation and ConnectionsUnpacking Antenna connection Front panel separation InstallationStand Front panel mounting HM-151 Required connectionsGround p Remot E p 4 p Advanced connectionsSpea KER p Used for computer control and transceive Operation Connecting a DC power supply Power supply connectionsBattery connections Connecting the AH-4 External antenna tuners MHz linear ampliﬁer Connecting the IC-PW1/EUROLinear ampliﬁer connections OPC-599 conversion cable Connections for CW For no break-in operation ACC Rtty EXT SP When connecting to MIC connector When connecting to Data socketWhen connecting to ACC socket Connections for packet Menu resetting M-1 When ﬁrst applying power CPU resettingInitial settings Basic Operation VFO description Differences between VFO and memory modeVFO Mode Example Selecting VFO A/VFO B Selecting VFO/memory modeVFO operation VFO equalization Selecting an operating band Using the band stacking registersBand Register Direct frequency entry with the microphone’s keypad Frequency settingTuning with the main dial Push F-INP/ENT Push TS momentarily to turn the programmable tuning step on Programmable tuning stepRotate Dial for normal tuning, if desired Selecting kHz step MHz quick tuning step FM/WFM/AM only Selecting 1 Hz or 10 Hz step SSB/CW/RTTY only ⁄4 tuning function CW/RTTY only Select M-3 Push ZMENU/GRP twice to return to the normal operating mode Volume settingAuto tuning step function Push ZMENU/GRP twice to return the normal op- erating mode Operating mode selection Voice synthesizer function When functioning as squelch control RF gain is Setting OperationWhen setting as RF gain/squelch control Squelch and receive RF sensitivity Quick entry Meter functionMulti-function meter Select S-1 Dial lock function Lock functionsBasic transmit operation Microphone lock function Setting microphone gain Setting output powerBand SSB/CW Operating SSB Receive and TransmitConvenient functions for receive About 5 MHz band operation USA version only IC-7000 Tuning FCC ChannelConvenient functions for transmit Transmit quality monitor p Operating CW Set CW setting in the keyer set mode S-10Stop keying to return to receive Break-in function p Memory keyer function p Push P.AMP/ATT momentarily to turn the pre- amp on or OFF⁄4 function p While M-3 is selected, push F-1BRK one or Push ZMENU/GRP to exit the quick set mode CW reverse modeCW side tone function CW pitch control Electronic CW keyer Memory keyer send menu Pre-set characters can be sent using the memorySelect S-1 Push F-2KEY to enter the keyer send menu Programming contents DEditing a keyer memory Number Style Contest number set modeSetting the contact serial number Count UP Trigger Keyer Repeat Time Keyer set modeSetting the electronic keyer Dot/Dash Ratio Paddle Polarity Keyer set mode Rise TimePaddle operation from MIC connector Keyer Type Display the Rtty decoder screen Transmit a Send signal from your TNCOperating Rtty FSK Rotate Dial to simultaneously tune a desired sig- nal Convenient functions for receive Twin peak ﬁlter Rtty reverse modeMode Setting the decoder threshold level Function for the Rtty decoder indication Rtty Decode Usos Rtty decode set modeRtty Decode New Line Code Rotate Dial to select the desired frequency Pre-setting for using Rtty terminal or TNCMark frequency Shift width Operating AM DSP noise reduction p Auto notch ﬁlter p Push NR/LEV to turn the DSP noise reduction Amp on or OFF On and OFF Operating FMPreamp and attenuator p DSP noise reduction p While M-3 is selected, push F-1 VOX to turn Tone squelch operation Push Mode one or more times to select FM mode Select M-3Push F-3TON for 1 sec. to enter the FM tone set mode Rotate Dial to set the desired subaudible tone frequency Push ZMENU/GRP to exit the FM tone set mode Tone scan operation Push F-3TON once or twice to turn the Dtcs function on Dtcs operationAvailable tone codes One-touch repeater function Repeater operationPush F-3TON to turn the repeater tone on Repeater tone frequency Push F-3TON once or twice to turn the tone en- coder on Auto repeater function Transmit frequency monitor checkFrequency range and offset direction Turn the auto repeater function OFF in the miscel Storing a non standard repeaterSelect M-2 Dtmf memory encoder Dtmf send menu Dtmf speed Push Mode to select FM mode. w Select S-1Programming a Dtmf code Push F-2DTM then ZMENU/GRP to select the Dtmf root menu Rotate M-chinner control to select the desired TV channel Push and hold Afset for 1 sec. to turn the TV mode onTV channel operation Rotate AF to set a suitable audio level Skip channel setting Push ZMENU/GRP to exit the channel frequency set mode Channel frequency adjustmentRotate Dial to adjust the channel frequency Push F-3SET to set the channel frequency Functions for Receive Fix modeSimple band scope Push F-3FIX momentarily to select the center mode Center modeScope set mode Select G-1 Scope Scope Size Preamp and attenuatorMax Hold Fast Sweep RIT function To reset the RIT frequency, push F-3CLR for 1 secTo cancel the RIT function, push F-1RIT mo- mentarily again Calculate function AGC time constant selection Setting the AGC time constantAGC function Selectable AGC time constant unit sec If ﬁlter selection If ﬁlter for WFM mode is ﬁxed and cannot be changedIf ﬁlter selection Select the desired mode. w Select M-1 Push F-3FIL for 1 sec. to enter ﬁlter set mode FIlter passband width setting SSB/CW/RTTY/AM onlySelect SSB, CW, Rtty or AM mode If fIlter shape SSB/CW only Twin PBT operation PBT Operation Example NB Level Noise blanker set modeNoise blanker NB Width Noise reduction Noise reduction set modeNR Level Auto notch function Mode While in CW and Rtty modes, push MNF/ADJNotch function This transceiver has auto and manual notch func Manual notch ﬁlter set mode Manual notch function Meter peak hold function Erating modeVoice squelch control function Push ZMENU/GRP twice to return to normal op Functions for Transmit Adjusting the VOX functionVOX function VOX Delay Transmit ﬁlter width setting SSB onlyVOX set mode VOX Gain Anti-VOX Semi break-in operation Break-in delay settingBreak-in function Full break-in operation ∂TX function To reset the ∂TX frequency, push F-3CLR for 1 secTo cancel the ∂TX function, push F-2∂TX mo- mentarily again Rotate RIT outer control to shift the transmitter frequency Monitor function Speech compressor Select Comp meter Select S-1 Compression level settingComp Level Push F-3MET one or more times to select the Comp meter Direct Shift Frequency Input Split frequency operationSelect VFO a and set the frequency to 21.290 MHz USB Push F-1SPL M-1 on the transceiver’s front panel Menu selection Example M-1 Quick split functionPush F-INP/ENT,, 5 then F-1 SPL M-1 Erating mode Split offset frequency settingQuick split setting Rotate Dial to set the desired split offset Spot measurement Measuring SWRMenu selection Example S-1 Plot measurement Recording a received audio Voice Recorder FunctionsDigital voice recorder Basic recording Playing the recorded contents Erasing the recorded contents Push F-3REC again to stop recording Recording a message for transmitRecording Push ZMENU/GRP twice to exit the voice mem- ory screen Input the desired character by rotating Dial Programming a memory name for transmitSpaces can be used. See the step t below Push ZMENU/GRP to input and set the name Select S-1 Push F-1VO to call up the voice recorder menu Transmit level settingSending a recorded message Push F-1T1 F-4T4 to transmit the con- tents Voice set mode Auto Monitor Voice set modeMIC Memo Memory channel selection Memory OperationMemory channels Memory Transfer Over Channel Capability Clear Memory programming Programming in VFO modeSet the desired frequency and operating mode in VFO mode Rotate M-chto select the desired memory chan- nel Programming in memory mode Set the desired frequency and operating mode Selecting a memory channel using the memory channel list Memory channel list Selecting a memory bank Setting a memory channel as a select memoryMemory channel list indication Memory names Editing programming memory names Memory clearing Memory clearing using the memory channel listTo return to VFO mode, push F-4V/M again Frequency transferring Transferring in VFO modeSelect a memory channel with M-ch Transferring in memory mode Push F-4V/M momentarily to select the VFO mode Memo pads Writing frequencies and operating modes into memo pads Calling up a frequency from a memo pad Scan types Scan OperationPreparation Programmed scan operation Memory scan operation Select memory scan operation Priority watch Optional AT-180 Automatic Antenna Tuner operation Manual tuningAntenna Tuner Operation Tuner operation AH-4 operation PTT tune function Packet Operation Adjusting the data speedAdjusting the transmit signal output from the TNC Packet operation Clock and Timers Time set mode Setting the current date Setting the current yearSetting the current time Set the desired power-off time using Dial Clock2 offset settingAuto power OFF activity Push ZMENU/GRP twice to exit timer set mode SET Mode Set mode description Mode Set mode item Default setting RF Power Quick set modeSSB TBW Wide L SSB mode RF Power all modes SSB TBW MID H SSB mode SSB TBW Wide H SSB modeSSB TBW MID L SSB mode SSB TBW NAR L SSB mode Twin Peak Filter Rtty mode Side Tone Level CW modeSide Tone Level Limit CW mode Rtty Mark Frequency Rtty mode Display set mode Display Font Size 12 1Hz Mode PopupDisplay Font Type Meter Peak Hold Voice TX Name Display TV Popup CH Up/DownTV Popup P.AMP/ATT Keyer Memory Display My Call Power on CheckPush ZMENU/GRP twice to exit the set mode screen Opening screen example Miscellaneous others set mode Split Offset RF/SQL ControlQuick Split DUP Offset HF One Touch Repeater DUP Offset 144MDUP Offset 430M Auto Repeater Vsend Select Tuner SwitchTuner PTT Start Speech Level Memopad Numbers Speech Mode SwitchSpeech S-Level Scan Speed 31 HM-151 F-2 34 SSB/CW Synchronous Tuning30 HM-151 F-1 MIC Up/Down Speed Mode Select Rtty Mode Select SSBMode Select CW CW Normal Side Mode Select WFM Mode Select AMMode Select FM External Keypad Voice CI-V Baud Rate REF AdjustFront Keypad Type CI-V Address Memory backup MaintenanceFuse replacement Cleaning Troubleshooting Est Icom Dealer or Service Center Transmit Display Scan Problem Possible Cause Solution Option Units Setting MB-106CARRYING Handle AT-180 inside top cover AT-180 internal switch descriptionConnector information for ACC2 socket Speciﬁcations for the AT-180 Remote jack CI-V information Control CommandCommand table CI-V connection example Control Command 146 147 Codes for memory keyer contents To send/read memory contentsBand stacking register Repeater tone/tone squelch frequency Setting Codes for memory name contentsSplit/Duplex frequency setting Dtcs code and polarity setting Specifications General Options MB-62 OPC-1444 OPC-1443OPC-589 Main menu group Sub menu group Menu GuideGraphic menu group Set mode description Memo Memo Intended Country of Use