Maintenance, Fuse replacement, Memory backup | Icom IC-7000 specs

14 MAINTENANCE

■Fuse replacement

If a fuse blows or the transceiver stops functioning, try to ﬁnd the source of the problem, and replace the dam- aged fuse with a new, rated fuse.

CAUTION: Disconnect the DC power cable from the transceiver when changing a fuse.

The IC-7000 has three of fuses (DC power cable fuses

⋅2, circuitry fuse⋅ 1) installed for transceiver protection.

•DC power cable fuses	ATC20 30 A
•Circuitry fuse	ATC20 5 A

DC power cable fuse replacement

CIRCUITRY FUSE REPLACEMENT

The 13.8 V DC from the DC power cable is applied to all units in the IC-7000, except for the power ampli- ﬁer, through the circuitry fuse. This fuse is installed in the FRONT unit.

R WARNING: NEVER attempt to remove fuse

coverusing your ﬁnger nails, this may result in in- jury.

Screw driver

Fuse cover

Fuse

■Memory backup

All of the CPU’s memory is backed up by an EEP- ROM (Electronically-Erasable Programmable Read- Only Memory). All data you set, such as VFO, memory, set mode contents, etc. is stored in this EEPROM. There is no internal lithium battery.

■Cleaning

If the transceiver becomes dusty or dirty, wipe it clean with a dry, soft cloth.

AVOID the use of strong chemical solvents such as thinner, benzine or alcohol to clean the transceiver. These may damage the transceiver’s surfaces.

139

Image 148

Icom IC-7000 instruction manual Maintenance, Fuse replacement, Memory backup, Cleaning, Circuitry Fuse Replacement

Contents

I7000 Word Definition Rwarning Shock may occurEquipment damage may occur Risk or personal injury, fire or electric Illustrations 7MAIN Dial Dial 8RECEIVE/TRANSMIT Indicators RX/TX Power Indicator Programmable Function Keys F-1/F-2Front panel Microphone HM-151 Precautions Table of Contents Transmit ﬁlter width setting SSB only ……… Hz tone burst ………………………………SSB/CW/RTTY/AM only …………………… NR Level …………………………………… Operation………………………………………… AH-4 operation ……………………………… From the TNC ………………………………… Specifications ………………………… General ………………………………………… Transmitter……………………………………… Panel Description Twin PBT M-ch/RIT Indicator Pgs , 79, 88 Panel DescriptionMENU/GROUP Keys MENU/GRP p TUNER/CALL KEY TUNER/CALL 1AUTO NOTCH/VOICE Recorder KEY ANF/ REC 2SPCH/LOCK KEY SPCH/LOCK4UP/DOWN Band Keys YBAND/ZBAND 7MAIN Dial Dial 9TUNING Step KEY TS pgs @2FUNCTION Display Multi-function keys Menu M-1 functionsMenu M-2 functions Menu M-3 functions Function FM Tone Operation Menu S-1 functions Menu S-2 functionsDtmf Operation Select Scan Menu G-1 Scope functions Menu S-3 functionsSweep Speed Power Indicator ⁄1VFO/MEMORY Selection V/M⁄2TRANSMIT Frequency Check XFC ⁄3TUNER/CALL KEY TUNER/CALL Microphone connector Microphone Connector Information Rear panel Data socket ACC socket When connecting the ACC conversion cable OPC-599 Function displayFrequency Readout Meter Readouts Appears when the preamp is on Appears when the 12 dB attenuator is@01/4 Function Indicator 7MULTI-FUNCTION Screen Installation and Connections UnpackingSelecting a location Antenna connection Installation StandFront panel separation Front panel mounting HM-151 Required connectionsGround p Advanced connections Spea KER pRemot E p 4 p Used for computer control and transceive Operation Connecting a DC power supply Power supply connectionsBattery connections Connecting the AH-4 External antenna tuners Connecting the IC-PW1/EURO Linear ampliﬁer connectionsMHz linear ampliﬁer OPC-599 conversion cable Connections for CW For no break-in operation ACC Rtty EXT SP When connecting to Data socket When connecting to ACC socketWhen connecting to MIC connector Connections for packet When ﬁrst applying power CPU resetting Initial settingsMenu resetting M-1 Basic Operation Differences between VFO and memory mode VFO ModeVFO description Example Selecting VFO/memory mode VFO operationSelecting VFO A/VFO B VFO equalization Selecting an operating band Using the band stacking registersBand Register Frequency setting Tuning with the main dialDirect frequency entry with the microphone’s keypad Push F-INP/ENT Programmable tuning step Rotate Dial for normal tuning, if desiredPush TS momentarily to turn the programmable tuning step on Selecting kHz step MHz quick tuning step FM/WFM/AM only Selecting 1 Hz or 10 Hz step SSB/CW/RTTY only ⁄4 tuning function CW/RTTY only Select M-3 Volume setting Auto tuning step functionPush ZMENU/GRP twice to return to the normal operating mode Push ZMENU/GRP twice to return the normal op- erating mode Operating mode selection Voice synthesizer function Setting Operation When setting as RF gain/squelch controlWhen functioning as squelch control RF gain is Squelch and receive RF sensitivity Meter function Multi-function meterQuick entry Select S-1 Lock functions Basic transmit operationDial lock function Microphone lock function Setting microphone gain Setting output powerBand SSB/CW Operating SSB Receive and TransmitConvenient functions for receive IC-7000 Tuning FCC Channel Convenient functions for transmitAbout 5 MHz band operation USA version only Transmit quality monitor p Operating CW Set CW setting in the keyer set mode S-10Stop keying to return to receive Push P.AMP/ATT momentarily to turn the pre- amp on or OFF ⁄4 function pBreak-in function p Memory keyer function p While M-3 is selected, push F-1BRK one or Push ZMENU/GRP to exit the quick set mode CW reverse modeCW side tone function CW pitch control Electronic CW keyer Memory keyer send menu Pre-set characters can be sent using the memorySelect S-1 Push F-2KEY to enter the keyer send menu Programming contents DEditing a keyer memory Contest number set mode Setting the contact serial numberNumber Style Count UP Trigger Keyer set mode Setting the electronic keyerKeyer Repeat Time Dot/Dash Ratio Keyer set mode Rise Time Paddle operation from MIC connectorPaddle Polarity Keyer Type Transmit a Send signal from your TNC Operating Rtty FSKDisplay the Rtty decoder screen Rotate Dial to simultaneously tune a desired sig- nal Convenient functions for receive Twin peak ﬁlter Rtty reverse modeMode Setting the decoder threshold level Function for the Rtty decoder indication Rtty Decode Usos Rtty decode set modeRtty Decode New Line Code Pre-setting for using Rtty terminal or TNC Mark frequencyRotate Dial to select the desired frequency Shift width Operating AM DSP noise reduction p Auto notch ﬁlter p Push NR/LEV to turn the DSP noise reduction Operating FM Preamp and attenuator p DSP noise reduction pAmp on or OFF On and OFF While M-3 is selected, push F-1 VOX to turn Push Mode one or more times to select FM mode Select M-3 Push F-3TON for 1 sec. to enter the FM tone set modeTone squelch operation Rotate Dial to set the desired subaudible tone frequency Push ZMENU/GRP to exit the FM tone set mode Tone scan operation Push F-3TON once or twice to turn the Dtcs function on Dtcs operationAvailable tone codes One-touch repeater function Repeater operationPush F-3TON to turn the repeater tone on Repeater tone frequency Push F-3TON once or twice to turn the tone en- coder on Auto repeater function Transmit frequency monitor checkFrequency range and offset direction Turn the auto repeater function OFF in the miscel Storing a non standard repeaterSelect M-2 Dtmf memory encoder Dtmf send menu Push Mode to select FM mode. w Select S-1 Programming a Dtmf codeDtmf speed Push F-2DTM then ZMENU/GRP to select the Dtmf root menu Push and hold Afset for 1 sec. to turn the TV mode on TV channel operationRotate M-chinner control to select the desired TV channel Rotate AF to set a suitable audio level Skip channel setting Channel frequency adjustment Rotate Dial to adjust the channel frequencyPush ZMENU/GRP to exit the channel frequency set mode Push F-3SET to set the channel frequency Functions for Receive Fix modeSimple band scope Center mode Scope set modePush F-3FIX momentarily to select the center mode Select G-1 Scope Preamp and attenuator Max HoldScope Size Fast Sweep To reset the RIT frequency, push F-3CLR for 1 sec To cancel the RIT function, push F-1RIT mo- mentarily againRIT function Calculate function Setting the AGC time constant AGC functionAGC time constant selection Selectable AGC time constant unit sec If ﬁlter for WFM mode is ﬁxed and cannot be changed If ﬁlter selectionIf ﬁlter selection Select the desired mode. w Select M-1 FIlter passband width setting SSB/CW/RTTY/AM only Select SSB, CW, Rtty or AM modePush F-3FIL for 1 sec. to enter ﬁlter set mode If fIlter shape SSB/CW only Twin PBT operation PBT Operation Example Noise blanker set mode Noise blankerNB Level NB Width Noise reduction Noise reduction set modeNR Level Mode While in CW and Rtty modes, push MNF/ADJ Notch functionAuto notch function This transceiver has auto and manual notch func Manual notch ﬁlter set mode Manual notch function Erating mode Voice squelch control functionMeter peak hold function Push ZMENU/GRP twice to return to normal op Functions for Transmit Adjusting the VOX functionVOX function Transmit ﬁlter width setting SSB only VOX set mode VOX GainVOX Delay Anti-VOX Break-in delay setting Break-in functionSemi break-in operation Full break-in operation To reset the ∂TX frequency, push F-3CLR for 1 sec To cancel the ∂TX function, push F-2∂TX mo- mentarily again∂TX function Rotate RIT outer control to shift the transmitter frequency Monitor function Speech compressor Compression level setting Comp LevelSelect Comp meter Select S-1 Push F-3MET one or more times to select the Comp meter Split frequency operation Select VFO a and set the frequency to 21.290 MHz USBDirect Shift Frequency Input Push F-1SPL M-1 on the transceiver’s front panel Menu selection Example M-1 Quick split functionPush F-INP/ENT,, 5 then F-1 SPL M-1 Split offset frequency setting Quick split settingErating mode Rotate Dial to set the desired split offset Measuring SWR Menu selection Example S-1Spot measurement Plot measurement Voice Recorder Functions Digital voice recorderRecording a received audio Basic recording Playing the recorded contents Erasing the recorded contents Recording a message for transmit RecordingPush F-3REC again to stop recording Push ZMENU/GRP twice to exit the voice mem- ory screen Programming a memory name for transmit Spaces can be used. See the step t belowInput the desired character by rotating Dial Push ZMENU/GRP to input and set the name Transmit level setting Sending a recorded messageSelect S-1 Push F-1VO to call up the voice recorder menu Push F-1T1 F-4T4 to transmit the con- tents Voice set mode Auto Monitor Voice set modeMIC Memo Memory Operation Memory channelsMemory channel selection Memory Transfer Over Channel Capability Clear Programming in VFO mode Set the desired frequency and operating mode in VFO modeMemory programming Rotate M-chto select the desired memory chan- nel Programming in memory mode Set the desired frequency and operating mode Selecting a memory channel using the memory channel list Memory channel list Selecting a memory bank Setting a memory channel as a select memoryMemory channel list indication Memory names Editing programming memory names Memory clearing Memory clearing using the memory channel listTo return to VFO mode, push F-4V/M again Frequency transferring Transferring in VFO modeSelect a memory channel with M-ch Transferring in memory mode Push F-4V/M momentarily to select the VFO mode Memo pads Writing frequencies and operating modes into memo pads Calling up a frequency from a memo pad Scan types Scan OperationPreparation Programmed scan operation Memory scan operation Select memory scan operation Priority watch Manual tuning Antenna Tuner OperationOptional AT-180 Automatic Antenna Tuner operation Tuner operation AH-4 operation PTT tune function Adjusting the data speed Adjusting the transmit signal output from the TNCPacket Operation Packet operation Clock and Timers Time set mode Setting the current date Setting the current yearSetting the current time Clock2 offset setting Auto power OFF activitySet the desired power-off time using Dial Push ZMENU/GRP twice to exit timer set mode SET Mode Set mode description Quick set mode SSB TBW Wide L SSB modeMode Set mode item Default setting RF Power RF Power all modes SSB TBW Wide H SSB mode SSB TBW MID L SSB modeSSB TBW MID H SSB mode SSB TBW NAR L SSB mode Side Tone Level CW mode Side Tone Level Limit CW modeTwin Peak Filter Rtty mode Rtty Mark Frequency Rtty mode Display set mode 12 1Hz Mode Popup Display Font TypeDisplay Font Size Meter Peak Hold TV Popup CH Up/Down TV Popup P.AMP/ATTVoice TX Name Display Keyer Memory Display Power on Check Push ZMENU/GRP twice to exit the set mode screenMy Call Opening screen example Miscellaneous others set mode RF/SQL Control Quick SplitSplit Offset DUP Offset HF DUP Offset 144M DUP Offset 430MOne Touch Repeater Auto Repeater Tuner Switch Tuner PTT StartVsend Select Speech Level Speech Mode Switch Speech S-LevelMemopad Numbers Scan Speed 34 SSB/CW Synchronous Tuning 30 HM-151 F-131 HM-151 F-2 MIC Up/Down Speed Mode Select SSB Mode Select CWMode Select Rtty CW Normal Side Mode Select AM Mode Select FMMode Select WFM External Keypad Voice REF Adjust Front Keypad TypeCI-V Baud Rate CI-V Address Maintenance Fuse replacementMemory backup Cleaning Troubleshooting Est Icom Dealer or Service Center Transmit Display Scan Problem Possible Cause Solution Option Units Setting MB-106CARRYING Handle AT-180 internal switch description Connector information for ACC2 socketAT-180 inside top cover Speciﬁcations for the AT-180 Control Command Command tableRemote jack CI-V information CI-V connection example Control Command 146 147 Codes for memory keyer contents To send/read memory contentsBand stacking register Codes for memory name contents Split/Duplex frequency settingRepeater tone/tone squelch frequency Setting Dtcs code and polarity setting Specifications General Options MB-62 OPC-1444 OPC-1443OPC-589 Main menu group Sub menu group Menu GuideGraphic menu group Set mode description Memo Memo Intended Country of Use