Compression level setting, Comp Level | Icom IC-7000 guide

FUNCTIONS FOR TRANSMIT

6

DCompression level setting

•Pre-setting the transceiver

[AF]

[MENU/GRP] [F-1] [F-2] [F-3]

[DIAL]

q Select an SSB mode.

w Turn the speech compressor function OFF, if it’s ON.

●Select M-1.

•Push and hold [MENU/GRP] for 1 sec. once or

twice to select the menu group M.

•Push [MENU/GRP] momentarily one or more times to select the menu M-1.

●Push [F-2COM] momentarily to turn the speech compressor function OFF.

•“ ” disappears.

e Select ALC meter.

●Select S-1.

●Push [F-3MET] one or more times to select the

ALC meter.

•“ALC” appears.

r Adjust the MIC gain.

●Push [AF(SET)] momentarily to enter the set mode menu.

●Push [F-1QS] to enter the quick set mode.

●Push [F-1Y] or [F-2Z] to select “MIC Gain.”

●Push [PTT] (microphone) to transmit at your normal voice level.

●While speaking into the microphone, rotate [DIAL] so that the ALC meter reads within the ALC zone, whether you speak softly or loudly.

●Push [Z(MENU/GRP)] twice to return normal op- erating mode.

•Compression level setting

[MENU/GRP] [F-2] [F-3]

[DIAL]

q Select COMP meter.

●Select S-1.

•Push and hold [MENU/GRP] for 1 sec. once or

twice to select the menu group S.

•Push [MENU/GRP] momentarily one or more times to select the menu S-1.

●Push [F-3MET] one or more times to select the COMP meter.

•“ ” appears.

w Turn ON the speech compressor function and enter the speech compression level set mode.

●Select M-1.

●Push [F-2COM] for 1 sec. to enter the speech

compression level set mode.

•speech compressor function automatically turns ON.

e Rotate [DIAL] so that the COMP meter reads be- tween 10 dB to 20 dB.

Appears

NOTE: When the ALC meter peaks below the ALC zone, your transmitted voice may be distorted.

ALC

ALC zone

Adjust ‘COMP LEVEL’ so that the ALC meter peaks above the ALC zone.

6

COMP Level

This item adjusts the speech compression level. The speech compression level can be adjusted from 0 to 10.

• Push [F-4DEF] for 1 sec. to return to default level.

5

5 (default)

90

Image 99

Icom IC-7000 instruction manual Compression level setting, Comp Level, Select Comp meter Select S-1

Contents

I7000 Risk or personal injury, fire or electric Word Definition RwarningShock may occur Equipment damage may occur Illustrations Microphone HM-151 7MAIN Dial Dial 8RECEIVE/TRANSMIT Indicators RX/TXPower Indicator Programmable Function Keys F-1/F-2 Front panel Precautions Table of Contents NR Level …………………………………… Transmit ﬁlter width setting SSB only ………Hz tone burst ……………………………… SSB/CW/RTTY/AM only …………………… From the TNC ………………………………… Operation………………………………………… AH-4 operation ……………………………… General ………………………………………… Transmitter……………………………………… Specifications ………………………… Panel Description TUNER/CALL KEY TUNER/CALL Twin PBT M-ch/RIT Indicator Pgs , 79, 88Panel Description MENU/GROUP Keys MENU/GRP p 7MAIN Dial Dial 1AUTO NOTCH/VOICE Recorder KEY ANF/ REC2SPCH/LOCK KEY SPCH/LOCK 4UP/DOWN Band Keys YBAND/ZBAND @2FUNCTION Display 9TUNING Step KEY TS pgs Menu M-3 functions Multi-function keysMenu M-1 functions Menu M-2 functions FM Tone Operation Function Select Scan Menu S-1 functionsMenu S-2 functions Dtmf Operation Menu S-3 functions Menu G-1 Scope functionsSweep Speed ⁄3TUNER/CALL KEY TUNER/CALL Power Indicator⁄1VFO/MEMORY Selection V/M ⁄2TRANSMIT Frequency Check XFC Microphone Connector Information Microphone connector Rear panel ACC socket Data socket Meter Readouts When connecting the ACC conversion cable OPC-599Function display Frequency Readout 7MULTI-FUNCTION Screen Appears when the preamp is onAppears when the 12 dB attenuator is @01/4 Function Indicator Antenna connection Installation and ConnectionsUnpacking Selecting a location Front panel mounting InstallationStand Front panel separation Required connections HM-151Ground p Used for computer control and transceive Operation Advanced connectionsSpea KER p Remot E p 4 p Power supply connections Connecting a DC power supplyBattery connections External antenna tuners Connecting the AH-4 OPC-599 conversion cable Connecting the IC-PW1/EUROLinear ampliﬁer connections MHz linear ampliﬁer For no break-in operation Connections for CW ACC Rtty EXT SP Connections for packet When connecting to Data socketWhen connecting to ACC socket When connecting to MIC connector Basic Operation When ﬁrst applying power CPU resettingInitial settings Menu resetting M-1 Example Differences between VFO and memory modeVFO Mode VFO description VFO equalization Selecting VFO/memory modeVFO operation Selecting VFO A/VFO B Using the band stacking registers Selecting an operating bandBand Register Push F-INP/ENT Frequency settingTuning with the main dial Direct frequency entry with the microphone’s keypad Selecting kHz step Programmable tuning stepRotate Dial for normal tuning, if desired Push TS momentarily to turn the programmable tuning step on Selecting 1 Hz or 10 Hz step SSB/CW/RTTY only MHz quick tuning step FM/WFM/AM only Select M-3 ⁄4 tuning function CW/RTTY only Push ZMENU/GRP twice to return the normal op- erating mode Volume settingAuto tuning step function Push ZMENU/GRP twice to return to the normal operating mode Voice synthesizer function Operating mode selection Squelch and receive RF sensitivity Setting OperationWhen setting as RF gain/squelch control When functioning as squelch control RF gain is Select S-1 Meter functionMulti-function meter Quick entry Microphone lock function Lock functionsBasic transmit operation Dial lock function Setting output power Setting microphone gainBand SSB/CW Receive and Transmit Operating SSBConvenient functions for receive Transmit quality monitor p IC-7000 Tuning FCC ChannelConvenient functions for transmit About 5 MHz band operation USA version only Set CW setting in the keyer set mode S-1 Operating CW0Stop keying to return to receive While M-3 is selected, push F-1BRK one or Push P.AMP/ATT momentarily to turn the pre- amp on or OFF⁄4 function p Break-in function p Memory keyer function p CW reverse mode Push ZMENU/GRP to exit the quick set modeCW side tone function CW pitch control Electronic CW keyer Pre-set characters can be sent using the memory Memory keyer send menuSelect S-1 Push F-2KEY to enter the keyer send menu DEditing a keyer memory Programming contents Count UP Trigger Contest number set modeSetting the contact serial number Number Style Dot/Dash Ratio Keyer set modeSetting the electronic keyer Keyer Repeat Time Keyer Type Keyer set mode Rise TimePaddle operation from MIC connector Paddle Polarity Rotate Dial to simultaneously tune a desired sig- nal Transmit a Send signal from your TNCOperating Rtty FSK Display the Rtty decoder screen Convenient functions for receive Rtty reverse mode Twin peak ﬁlterMode Function for the Rtty decoder indication Setting the decoder threshold level Rtty decode set mode Rtty Decode UsosRtty Decode New Line Code Shift width Pre-setting for using Rtty terminal or TNCMark frequency Rotate Dial to select the desired frequency Operating AM Push NR/LEV to turn the DSP noise reduction DSP noise reduction p Auto notch ﬁlter p While M-3 is selected, push F-1 VOX to turn Operating FMPreamp and attenuator p DSP noise reduction p Amp on or OFF On and OFF Rotate Dial to set the desired subaudible tone frequency Push Mode one or more times to select FM mode Select M-3Push F-3TON for 1 sec. to enter the FM tone set mode Tone squelch operation Tone scan operation Push ZMENU/GRP to exit the FM tone set mode Dtcs operation Push F-3TON once or twice to turn the Dtcs function onAvailable tone codes Repeater operation One-touch repeater functionPush F-3TON to turn the repeater tone on Push F-3TON once or twice to turn the tone en- coder on Repeater tone frequency Transmit frequency monitor check Auto repeater functionFrequency range and offset direction Storing a non standard repeater Turn the auto repeater function OFF in the miscelSelect M-2 Dtmf send menu Dtmf memory encoder Push F-2DTM then ZMENU/GRP to select the Dtmf root menu Push Mode to select FM mode. w Select S-1Programming a Dtmf code Dtmf speed Rotate AF to set a suitable audio level Push and hold Afset for 1 sec. to turn the TV mode onTV channel operation Rotate M-chinner control to select the desired TV channel Skip channel setting Push F-3SET to set the channel frequency Channel frequency adjustmentRotate Dial to adjust the channel frequency Push ZMENU/GRP to exit the channel frequency set mode Fix mode Functions for ReceiveSimple band scope Select G-1 Scope Center modeScope set mode Push F-3FIX momentarily to select the center mode Fast Sweep Preamp and attenuatorMax Hold Scope Size Calculate function To reset the RIT frequency, push F-3CLR for 1 secTo cancel the RIT function, push F-1RIT mo- mentarily again RIT function Selectable AGC time constant unit sec Setting the AGC time constantAGC function AGC time constant selection Select the desired mode. w Select M-1 If ﬁlter for WFM mode is ﬁxed and cannot be changedIf ﬁlter selection If ﬁlter selection If fIlter shape SSB/CW only FIlter passband width setting SSB/CW/RTTY/AM onlySelect SSB, CW, Rtty or AM mode Push F-3FIL for 1 sec. to enter ﬁlter set mode PBT Operation Example Twin PBT operation NB Width Noise blanker set modeNoise blanker NB Level Noise reduction set mode Noise reductionNR Level This transceiver has auto and manual notch func Mode While in CW and Rtty modes, push MNF/ADJNotch function Auto notch function Manual notch function Manual notch ﬁlter set mode Push ZMENU/GRP twice to return to normal op Erating modeVoice squelch control function Meter peak hold function Adjusting the VOX function Functions for TransmitVOX function Anti-VOX Transmit ﬁlter width setting SSB onlyVOX set mode VOX Gain VOX Delay Full break-in operation Break-in delay settingBreak-in function Semi break-in operation Rotate RIT outer control to shift the transmitter frequency To reset the ∂TX frequency, push F-3CLR for 1 secTo cancel the ∂TX function, push F-2∂TX mo- mentarily again ∂TX function Speech compressor Monitor function Push F-3MET one or more times to select the Comp meter Compression level settingComp Level Select Comp meter Select S-1 Push F-1SPL M-1 on the transceiver’s front panel Split frequency operationSelect VFO a and set the frequency to 21.290 MHz USB Direct Shift Frequency Input Quick split function Menu selection Example M-1Push F-INP/ENT,, 5 then F-1 SPL M-1 Rotate Dial to set the desired split offset Split offset frequency settingQuick split setting Erating mode Plot measurement Measuring SWRMenu selection Example S-1 Spot measurement Basic recording Voice Recorder FunctionsDigital voice recorder Recording a received audio Playing the recorded contents Erasing the recorded contents Push ZMENU/GRP twice to exit the voice mem- ory screen Recording a message for transmitRecording Push F-3REC again to stop recording Push ZMENU/GRP to input and set the name Programming a memory name for transmitSpaces can be used. See the step t below Input the desired character by rotating Dial Push F-1T1 F-4T4 to transmit the con- tents Transmit level settingSending a recorded message Select S-1 Push F-1VO to call up the voice recorder menu Voice set mode Voice set mode Auto MonitorMIC Memo Memory Transfer Over Channel Capability Clear Memory OperationMemory channels Memory channel selection Rotate M-chto select the desired memory chan- nel Programming in VFO modeSet the desired frequency and operating mode in VFO mode Memory programming Set the desired frequency and operating mode Programming in memory mode Memory channel list Selecting a memory channel using the memory channel list Setting a memory channel as a select memory Selecting a memory bankMemory channel list indication Editing programming memory names Memory names Memory clearing using the memory channel list Memory clearingTo return to VFO mode, push F-4V/M again Transferring in VFO mode Frequency transferringSelect a memory channel with M-ch Push F-4V/M momentarily to select the VFO mode Transferring in memory mode Writing frequencies and operating modes into memo pads Memo pads Calling up a frequency from a memo pad Scan Operation Scan typesPreparation Memory scan operation Programmed scan operation Priority watch Select memory scan operation Tuner operation Manual tuningAntenna Tuner Operation Optional AT-180 Automatic Antenna Tuner operation PTT tune function AH-4 operation Packet operation Adjusting the data speedAdjusting the transmit signal output from the TNC Packet Operation Time set mode Clock and Timers Setting the current year Setting the current dateSetting the current time Push ZMENU/GRP twice to exit timer set mode Clock2 offset settingAuto power OFF activity Set the desired power-off time using Dial Set mode description SET Mode RF Power all modes Quick set modeSSB TBW Wide L SSB mode Mode Set mode item Default setting RF Power SSB TBW NAR L SSB mode SSB TBW Wide H SSB modeSSB TBW MID L SSB mode SSB TBW MID H SSB mode Rtty Mark Frequency Rtty mode Side Tone Level CW modeSide Tone Level Limit CW mode Twin Peak Filter Rtty mode Display set mode Meter Peak Hold 12 1Hz Mode PopupDisplay Font Type Display Font Size Keyer Memory Display TV Popup CH Up/DownTV Popup P.AMP/ATT Voice TX Name Display Opening screen example Power on CheckPush ZMENU/GRP twice to exit the set mode screen My Call Miscellaneous others set mode DUP Offset HF RF/SQL ControlQuick Split Split Offset Auto Repeater DUP Offset 144MDUP Offset 430M One Touch Repeater Speech Level Tuner SwitchTuner PTT Start Vsend Select Scan Speed Speech Mode SwitchSpeech S-Level Memopad Numbers MIC Up/Down Speed 34 SSB/CW Synchronous Tuning30 HM-151 F-1 31 HM-151 F-2 CW Normal Side Mode Select SSBMode Select CW Mode Select Rtty External Keypad Voice Mode Select AMMode Select FM Mode Select WFM CI-V Address REF AdjustFront Keypad Type CI-V Baud Rate Cleaning MaintenanceFuse replacement Memory backup Est Icom Dealer or Service Center Troubleshooting Transmit Display Scan Problem Possible Cause Solution MB-106CARRYING Handle Option Units Setting Speciﬁcations for the AT-180 AT-180 internal switch descriptionConnector information for ACC2 socket AT-180 inside top cover CI-V connection example Control CommandCommand table Remote jack CI-V information Control Command 146 147 To send/read memory contents Codes for memory keyer contentsBand stacking register Dtcs code and polarity setting Codes for memory name contentsSplit/Duplex frequency setting Repeater tone/tone squelch frequency Setting General Specifications MB-62 Options OPC-1443 OPC-1444OPC-589 Menu Guide Main menu group Sub menu groupGraphic menu group Set mode description Memo Memo Intended Country of Use