Icom IC-7000 Power Indicator, ⁄1VFO/MEMORY Selection V/M, ⁄2TRANSMIT Frequency Check XFC

1PANEL DESCRIPTION

■Microphone (HM-151)

zSPCH/LOCK KEY [SPCH/LOCK]

➥Push momentarily to have the frequency, etc. an- nounced by the speech synthesizer. (p. 34)

•The parameters to be announced can be selected in the miscellaneous (others) set mode. (p. 134)

➥Push and hold for 1 sec. to toggle the microphone lock function ON and OFF. (p. 37)

xPTT SWITCH [PTT] (p. 37)

Push and hold to transmit; release to receive.

cUP/DOWN SWITCHES [Y]/[Z]

Change the operating frequency.

•Push and hold to change the frequency repeatedly. •Tuning step size is 50 Hz if no TS indicator is displayed.

vTRANSMIT INDICATOR

Lights red while transmitting.

bKEYPAD

➥Pushing a key selects the operating band.

•[(GENE)•] selects the general coverage band.

➥Pushing the same key 2 or 3 times calls up other stacked frequencies in the band. (p. 28)

•Icom’s triple band stacking register memorizes 3 fre- quencies in each band.

➥After pushing [(F-INP)ENT], enter a numeric fre- quency, followed by pressing [(F-INP)ENT]

again. (p. 29)

•e.g. to enter 14.195 MHz, push [(F-INP)ENT] [1] [4]

[•][1] [9] [5] [(F-INP)ENT].

nFILTER SELECTION [FIL] (p. 77)

➥Push momentarily to select one of three IF filter settings.

➥Push and hold for 1 sec. to enter the filter set mode.

mMODE KEY [MODE] (p. 34)

➥Push momentarily to cycle through the operating modes:

USB/LSB ➧ CW/CW-R ➧ RTTY/RTTY-R ➧ AM/FM/WFM

➥Push and hold for 1 sec. to toggle the following operating modes:

USB ↔ LSB

CW	↔ CW-R
RTTY ↔ RTTY-R
AM	→ FM → WFM → AM, etc

,POWER INDICATOR

Lights green while transceiver power is ON.

See the illustration of the HM-151 on page i-2.

.PROGRAMMABLE FUNCTION KEYS [F-1]/[F-2]

Program and perform a selected function.

•The functions can be assigned in the miscellaneous (oth- ers) set mode (p. 135). The default settings for [F-1]and [F-2]are “MPW” and “MPR,” respectively.

Default settings

[F-1](MPW): Push to store the selected readout frequency and operating mode into a memo pad.

[F-2](MPR): Push to call up a memo pad.

⁄0MEMORY WRITE [MW] (pgs. 103, 104)

Push and hold for 1 sec. to store the displayed VFO frequency and operating mode into the displayed memory channel.

⁄1VFO/MEMORY SELECTION [V/M]

➥Push momentarily to toggle VFO and memory modes. (pgs. 27, 102)

➥Push and hold for 1 sec. to transfer the selected memory channel to the currently displayed VFO. (p. 109)

⁄2TRANSMIT FREQUENCY CHECK [XFC]

(pgs. 65, 91)

Monitors the transmit frequency when pushed and held.

•While pushing this key, the transmit frequency can be changed with [DIAL].

⁄3TUNER/CALL KEY [TUNER/CALL]

➥During HF/50 MHz operation (p. 116):

●Push momentarily to toggle the automatic an- tenna tuner function ON and OFF.

•An optional antenna tuner must be connected.

•“” indicator appears when the tuner is ON.

●Push and hold for 2 sec. to manually tune the antenna.

•An optional antenna tuner must be connected.

•“” indicator appears when the tuner is ON.

➥During 144/430 MHz operation (p. 103):

Push momentarily to select the call channel (or return to the previous channel/frequency when the call channel is already selected).

•“C1” is the 144 MHz call channel and “C2” is the 430 MHz call channel.

9