Icom IC-7000 instruction manual Panel Description, Twin PBT M-ch/RIT Indicator Pgs , 79, 88

✔What is the PBT control?

PBT electronically narrows the IF passband width to reject interference. This transceiver uses DSP to implement PBT.

➥While M-ch/RIT is selected:

●Rotate the inner control to select a memory channel number (p. 102).

●Push inner control for 1 sec. to turn the RIT/∂TX mode ON (pgs. 75, 88).

•Push [Z(MENU/GRP)] to exit the RIT/∂TX mode.

●While the RIT/∂TX mode is OFF:

Rotates outer control to select a memory bank (p. 106).

●While the RIT/∂TX is ON:

Rotate outer control to shift the receive or transmit frequency (pgs. 75, 88).

•“” or “” indicators appear when the RIT or ∂TX function is activate, respectively.

•The shift frequency range is ± 9.999 kHz in 1 Hz steps (or ±9.99 kHz in 10 Hz steps).

		RIT
		M-ch
	M-ch		RIT
Channel	Channel	Frequency	Frequency
decreases	increases	decreases	increases

•When the RIT or ∂TX function is ON, push and hold [F-1RIT] or [F-2∂TX] for 1 sec. to add or subtract the frequency shift to the display fre- quency.

✔What is the RIT function?

RIT (Receiver Incremental Tuning) shifts the receive fre- quency without shifting the transmit frequency.

This is useful for fine tuning for stations calling you off fre- quency or when you prefer to listen to slightly different- sounding voice characteristics, etc.

✔What is the ∂TX function?

The ∂TX shifts the transmit frequency without shifting the re- ceive frequency. This is useful for simple split frequency op- eration in CW, etc.

PANEL DESCRIPTION	1
y TWIN PBT (M-ch/RIT) INDICATOR
		1
(pgs. 75, 79, 88, 102)

➥Indicates the status of [PBT/M-ch/RIT](t) acti- vates as the Twin PBT function or memory chan- nel/RIT control.

•Indicator is green when the Twin PBT is selected. •Indicator is off when the M-ch/RIT is selected. •Indicator is orange when the RIT or ∂TX function is activate.

uMENU/GROUP KEYS [MENU/GRP] (p. 153)

➥Push either key one or more times to select menus within a menu group (M, S or G (Graphic)).

➥Push and hold for 1 sec. to select one of the three menu groups: M-1to M-3, S-1to S-3and G-1(Scope) to G-3(SWR meter).

iTUNER/CALL KEY [TUNER/CALL]

➥During HF/50 MHz operation (p. 116):

●Push momentarily to toggle the automatic an- tenna tuner function ON and OFF.

•An optional antenna tuner must be connected.

•“” indicator appears when the tuner is ON.

●Push and hold for 2 sec. to manually tune the antenna.

•An optional antenna tuner must be connected.

•“” indicator appears when the tuner is ON.

➥During 144/430 MHz operation (p. 102):

Push momentarily to select the call channel (or return to the previous channel/frequency when the call channel is already selected).

•“C1” is the 144 MHz call channel and “C2” is the 430 MHz call channel.

oMULTI-FUNCTION KEYS [F-1]/[F-2]/[F-3]/[F-4]

➥Push to select the function indicated in the LCD display above these keys. (pgs. 5–8, 153)

•Functions vary depending on the active menu.

Functions appear

See the illustration of the Front panel on page i-2.

2