Manuals / Lucent Technologies / Computer Equipment / Server

Lucent Technologies Comcode 108678723 manual Troubleshooting ATM-CES

Models: Comcode 108678723

1 230

Download 230 pages 18.93 Kb

Page 139

DEFINITY ECS Release 8.2 ATM Installation,	Issue 1
Upgrades, and Administration 555-233-124	April 2000
6 Troubleshooting
Troubleshooting ATM-CES	6-5

Troubleshooting ATM-CES

Table 6-4 provides a first-level method for troubleshooting an installation.

Table 6-4. ATM-CES installation troubleshooting checklist

	Problem	Solution
	Is DEFINITY ECS software Release 7 or	Verify that software is Release 7 or later
	later?

	On System Parameters Maintenance
	screen	Set to correct field
	Is Bus Bridge field set to enabled? (csi)	Set to correct field
	Is Packet Bus field set to activated?	Verify/replace EI circuit packs
	(r,si)
	Are EI circuit packs TN570Bs or later?

	All COR, COS, UDP, FRLs, AAR, and ARS	Verify they are all set correctly
	support proper routing

The following list provides tips for further ATM-CES troubleshooting:

■Inspecting LEDs—Describes the possible LED states on the

—TN2305/TN2306 ATM interface circuit packs

—ATM switch

■Troubleshooting interoperability—Providesguidelines for troubleshooting

—Physical connections

—Administration

—TN2305/TN2306 circuit pack

—ATM signaling architecture

■Unusual ATM trouble conditions—Describes difficult-to-diagnose failure modes in the DEFINITY ECS and ATM switch combinations.

■DEFINITY ECS ATM-CES troubleshooting commands—Describes specific troubleshooting commands.

Image 139

Lucent Technologies Comcode 108678723 manual Troubleshooting ATM-CES

Contents

Definity Trademarks Contents Administering ATM-PNC About This Book Organization OverviewDefinity ECS Admonishments Conventions Used in This BookTypographic Systems and circuit packsRelated Books How to Comment on This DocumentPhysical dimensions ResourcesOther Resources How to Order BooksTopic Location Technical support contact numbers Telephone Number Where To Call for Technical SupportTrademarks Remove/Install Circuit PacksAntistatic Protection SecurityMegacom Systimax Transtalk Standards ComplianceLaser Product Power output Wavelength Mode field diameterElectromagnetic Compatibility Standards European Union Standards Part 68 Statement Federal Communications Commission StatementManufacturer’s Means of connectionPort Identifier FIC Code Network Jacks Definity ECS Release 8.2 ATM Installation Preparing for Installation Upgrades Request Address Information Figure Notes Review Configuration and EquipmentPPN Required HardwareIssue ATM-PNC connections for standard reliability Definity ECS configurationsATM-PNC connections for high reliability 1314 Determine ATM Switch Suitability Number of PP SVCs supported Network Layout Customer ATM switchSetups per second at 220 ms per setup Application bandwidth in kbps needed per port networkConstants Constraint testsComputed values Application scenarios Final notesTest results Known limits of commonly used ATM switches Known limits of commonly used ATM switches Schedule Installation or UpgradeATM-CES Equipment InstallationGeneral installation process Step Action Description See ‘‘DEFINITY ECS configurations’’ on page 1-6 forNAA7 board csi and c models only NAA7 Board csi/c models onlyIssue ATM-PNC See ‘‘DEFINITY ECS configurations’’ on page 1-6 for ‘‘Baselining the Customer’s Configuratio n’’ Synchronization Installation TestingConnections needing synchronization splitters Connections without synchronization splittersSplitter descriptions A synchronization splitter Network timing connection 401A 108508078402A 108508094 ECS 403A402A 108508094 Synchronization connections through an external DSU/CSU 400A Synchronization splitter connectionsSynchronization connections through an Icsu 400A Cydaatm3 KLC 400A Lists the splitter models applicable to specific countries Country-specific splitter applications T1 or E1 service verification procedure Verify the DS1 serviceCpe-loopback-jack-test Interpretation of the list measurements reportDisplayed Field Function Indication Stop the test test ds1-loop Uucss endSplitter port tests 401A/401A only Installing and testing the splitterTesting the splitter ports Step Action Command Description Installing a 400A T1 splitterInstalling the splitter through an Icsu Action Command Description 10. The 120A Icsu test procedure10. The 120A Icsu test procedure ‘‘Troubleshooting synchronization 400A Only’’ on 11. Testing the 120A 2 IcsuCommand Complete displays Uucss Through 145. If these tests pass and this is Step Action Command Description 14. DTE loopback testing for the 316X DSU/CSUOperational displays To integrated see Screen Installing 401A, 402A, or 403A splitters401A/401A only’’ on Screen 3-1. DS1 circuit pack-T1 ATM Network DuplicationScreen 3-2. DS1 circuit pack-E1 ATM Network Duplication EPN configuration with ATM network duplication Network duplication administration Screen 3-4. ATM PNC Screen 3-3. Optional feature-screenScreen 3-5. Duplication-related system parameters Type save translation and press Enter Type reset pnc interchange and press EnterChanging circuit packs on the standby PNC Type busyout pnc-standby and press EnterIssue Upgrading to ATM-PNC Upgrade pathsCritical reliability/network duplication only PreparationCSS to R8r ATM-PNC Issue Issue 1 April Record More Action Command Description Time Data Info Enable PNC Change Ensure that the Alarm Origination Record More Site-specific Appendix a ECS ATM R6.3r ATM-PNC to R8r ATM-PNC R7r ATM-PNC to R8r ATM-PNC Upgrading to ATM-PNC R7r ATM-PNC to R8r ATM-PNC Information Connection ESI field for each B-PNC ATM Yes? System-parameters Record More Site-specific comments More Info Screens and Tables Screen 4-1. Maintenance-related system parametersScreen 4-2. Port network connectivity Screen 4-4. ATM PNC PNC interchange PNC status DescriptionPnc-interchange Screen 4-3. CabinetScreen 4-5. Synchronization plan Screen 4-6. Optional features-screenScreen 4-8. System links information Screen 4-7. Optional features-screenAccessing Switches for Administration Acquiring ATM Addresses Issue Administering Definity ECS Administering ATM SwitchGeneral Definity ECS ATM parameters Concept Description ATM Port Network Connectivity ATM-PNC ATM-PNC administrationDCC ATM-CES rules ATM Circuit Emulation Service ATM-CESType change trunk-group trkgrpnbr Type change signaling-group192 248 Type display signaling-groupATM-CES trunk board Trunk groupsDefinity ECS trunk capacities by model Capacity Csi, si Definity signaling groups and members for ATM trunking ATM-CES administration Step Action Description ATM-CES administration procedureATM-CES administration Step Action Description KHz Screen 3-5 displays Trunk group can contain either Isdn or ATM Screen 5-1. Optional features-screen ATM-CES administration screensScreen 5-2. Optional features-screen Screen 5-4. Duplication related system parameters Screen 5-3. Optional features-screenScreen 5-5. ATM trunk board Channel Screen 5-6. Signaling groupValue Country Protocol supported Screen 5-7. Signaling group D-channel assignments-screenScreen 5-9. Trunk group-screen Screen 5-8. Trunk group-screen10. ATM administration commands Command Description Definity commands for CESChanging the port-to-channel mapping 11. Administer location procedure Step Action Description Additional Definity ECS administrationLocations Ensure that the Timezone Offset field for Type change daylight-savings-rules and press Enter Screen 5-11. Cabinet Screen 5-10. Optional features-screenField description Screen 5-12. Locations-screenDaylight Savings Rules Screen 5-13. Daylight savings rules screenScreen 5-14. Date and time screen Screen 5-15. ATM SVC cache report SVC cacheNone , lan , man , wan , and custom Gain/Loss adjustmentsType change system-parameters country-option s Screen 5-17 -type terminal parameters Screen 5-16. System parameters country-options-screenFinal Checklist and Test Issue Final Checklist and Test Troubleshooting Contact information Lucent service organizationsHelplines Alarms and errorsInternational customers Is responsible for overall Maintenance of an EPN Troubleshooting ATM-CES Inspecting LEDs Troubleshooting interoperabilityDiagnostics Has the ATM switch been installed and configured correctly?Definity ECS Release 8.2 ATM Installation Is Definity ECS ATM-CES administered correctly? AdministrationTroubleshooting CES Step Action Description TN2305/TN2306 circuit pack Is the ATM switch administered correctly?Did the TN2305/TN2306 come up correctly? Screen 6-1. Screen output for test board number Possible causes ATM signaling architecturePhysical layer Possible causes Recommended Action DiagnosticsSONET/SDH layer Call processing CaPro LayerAre talk paths being established between port networks? Screen 6-2. System links informationAction Unusual ATM trouble conditionsDefinity ECS ATM-CES troubleshooting commands Troubleshooting ATM-PNCInspecting LEDs Troubleshooting 400A synchronization through an Icsu Connected through a DSU/CSU Step Action Description Troubleshooting 400A T1 synchronization through a DSU/CSUTroubleshooting synchronization 401A/402A/403A Troubleshooting 401A/402A/403A synchronization Definity ECS switch administration Screen 6-4. Screen output for status pnc command Screen 6-3. Screen output for list atm pnc commandScreen 6-6. Screen output for circuit-packs Screen 6-5. Screen output for display circuit-packsScreen 6-7. Screen output for display atm pnc Administered with end system identifiersScreen 6-8. Screen output for display atm pnc PNC ATM signaling links ATM signaling links10. ATM signaling sequences Signaling between the PPN ATM switch administrationCall between EPN2 and EPN Screen 6-11. List configuration carrier 1b screen Screen 6-13. Screen output for test board Uucss Screen 6-12. List configuration carrier 2a screenField Value Possible causes Physical layer Saal data link layer 93B network layer Screen 6-15. Hardware error report-screen Screen 6-14. Error report11. Observed Cause Codes Definition ATM call controlAre talk paths being established between port networks? Diagnostics Diagnostics Change/display atm pnc-pairs Definity ECS ATM-PNC troubleshooting commandsList measurements atm pnc-latency Field descriptionsScreen 6-17. ATM-PNC latency measurements Conserving ATM bandwidthBandwidth-constricted ATM network configuration Alarming out-of-spec conditions SVC latency commands Alarming out-of-spec conditionsScreen 6-18. ATM-PNC latency histogram report SVC latency commandsField descriptions Screen Screen 6-19. ATM-PNC delayed/failed setups reportOptions form change system-parameters Screen 6-20. Optional features-screen Constricted bandwidth administration screensField descriptions Screen 6-21. ATM-related system parametersExample Alarm Reporting Screen 6-22. Alarm reporting options-screenATM Switch Administration Baselining the Customer’s ConfigurationFigure A-1. Sample lightwave interface unit LIU InterconnectionsDefinity ECS Administration Worksheet Table A-1 Customer ATM switch location Definity ECS switch locationFor Standard and High Reliability Systems WorksheetReliability SystemsTable a Definity ECS Release 8.2 ATM Installation Location-related Interactions Switch operabilityOperation Description Table B-1. Switch operability interactionsAttendant service from a local attendant on local time Feature performanceIssue Routing tables inaccurate Table B-3. Time of day impacts Use Group Impact Time of Day considerationsAAR Features SupportedFeature Description Issue Features Not Supported Table B-5. ATM delay interactions Feature Description Delay InteractionsTable B-5. ATM delay interactions ACD By SVC setup delays and failures Failures Issue Mmch Recorded Telephone ATM Feature Interactions AAR/ARS Table B-6. Release 7 or later ATM feature interactionsAffected by Race Feature Location Condition Description WAN PNC Digital data Conversant Cross-product CompatibilityNumerics ServiceATM network duplication GL-2 Escc OC-3 Meiners’ algorithmQoS PVCVirtual Path Identifier VPI Subnet TrunkingIndex H600-383,3-11,3-12,3-13,3-22,3-23 maximum run lengths IN-3 IN-4 IN-5 IN-6 We’d like your opinion