Port Statistics Data Window Entries | Q-Logic 8C/16 guide

5 – Managing Ports Displaying Port Information

Q

Table 5-5. Port Statistics Data Window Entries (Continued)

Entry	Description

Invalid CRC Count	Number of invalid Cyclic Redundancy Check (CRC) frames
	detected.
Tx Wait Count	Number of times the port entered a wait state because it didn't
	receive credit to transmit from the attached device.
Class 3 Toss Count	Number of class 2 and class 3 sequences that were discarded
	by this port. A sequence can be discarded because of
	detection of a missing frame (based on SEQ_CNT), detection
	of an E_D_TOV timeout, receiving a reject frame, receiving
	frames for a stopped sequence, or other causes.
FReject Count	Number of frames, from devices, that have been rejected.
	Frames can be rejected for any of a large number of reasons.
FBusy Count	Number of class 2 and class 3 fabric busy (F_BSY) frames
	generated by this port in response to incoming frames. This
	usually indicates a busy condition on the fabric or N_port that
	is preventing delivery of this frame.
Link Failures	Number of optical link failures detected by this port. A link
	failure is a loss of synchronization or by loss of signal while not
	in the offline state. A loss of signal causes the switch to
	attempt to re-establish the link. If the link is not re-established,
	a link failure is counted. A link reset is performed after a link
	failure.
Primitive Sequence	Number of bad primitives received by the port.
Errors
Rx Link Resets	Number of link reset primitives received from an attached
	device.
Tx Link Resets	Number of link reset primitives sent from this port to an
	attached port.
Rx Offline Sequences	Number of offline sequence primitives received by the port.
Tx Offline Sequences	Number of offline primitives transmitted by the port.
Total Errors	Total number of primitive and non-primitive port link errors.
Total Tx Frames	Total number of frames transmitted by the port.
Total Rx Frames	Total number of frames received by the port.
Total Tx Words	Total number of words transmitted by the port.
Total Rx Words	Total number of words received by the port.

5-6	59022-06 A

Image 104

Q-Logic 8C/16 manual Port Statistics Data Window Entries

Contents

SANbox2-8c/16 Switch Management User’s Guide SANbox2-8c/16 Switch Management User’s Guide Document Revision History Table of Contents Section Managing Fabrics Section Managing Switches Displaying Switch Information Section Managing Ports Appendix a Command Line Interface Command Syntax Initial Startup Dialog SANbox Manager Window Appendix B Graphing Port PerformanceGlossary Index Account Administration Add Account Administration Remove TablesMenu Shortcut Keys Tool Bar Buttons Severity Levels Edit Zoning Window Tool Bar Buttons Port Administrative States Port Speeds Port Modes Intended Audience Related Materials Technical Support AvailabilityTraining Contact Information Installing SANbox Manager Management Workstation Requirements SANsurfer Management Suite Disk Windows Installation SANsurfer Management Suite Disk Linux Installation Enter the following command SANsurfer Management Suite Disk Solaris Installation SANbox2 Installation Disk Solaris Installation SANbox2 Installation Disk Windows InstallationSANbox2 Installation Disk Linux Installation Starting SANbox Manager „ For a Linux platform, enter the SANboxManager command„ For a Solaris platform, enter the SANboxManager command SANbox Manager Window Save Default Fabric File Dialog SANbox Manager Exiting SANbox Manager Uninstalling SANbox Manager Changing the SANbox Manager Default Fabric File Password Saving and Opening SANbox Manager Fabric View Files Setting SANbox Manager Preferences Preferences Dialog SANbox Manager Using Online Help Viewing Software Version and Copyright Information Faceplate Display SANbox Manager User InterfaceTopology Display Switch Menu Bar Shortcut Selection Most menu selections have shortcut keys as shown in TableMenu Shortcut Keys Tool Bar Button Description Tool BarTool Bar Buttons Fabric Tree Fabric Tree Data Window and Tabs Working Status IndicatorGraphic Window Using the Topology Display Switch and Link Status Arranging Switches in the Display Working with Switches and LinksSelecting Switches and Links Opening the Faceplate Display and Topology Popup Menus Topology Data Windows Using the Faceplate Display Port Views and Status Opening the Faceplate Popup Menu Working with PortsSelecting Ports Faceplate Data Windows User Authentication Security Inter-Switch Link Security Inband Management Choose the Add Fabric button Managing the Fabric DatabaseAdding a Fabric Saving a Fabric View File Removing a FabricOpening a Fabric View File Adding a New Switch to a Fabric Rediscovering a Fabric Replacing a Failed Switch Fabric Status Deleting Switches and LinksDisplaying Fabric Information Topology Display Switch and Status Icons Switch Icon Description Displaying the Event Browser Events Browser Severity Levels Severity Description Icon Filtering the Event Browser Filter Events Dialog Sorting the Event Browser Save the Event Browser to a File Active Zone Set Data Window Active Zone Set Data Window Zones Zoning a FabricZoning Concepts Virtual Private Fabric Hard Zones Access Control List Hard ZonesSoft Zones Aliases Zone Sets Zoning Configuration Zoning Database FC-SW-2 Auto Save Using the Zoning Config DialogDefault Visibility Zone Merge Failure Restoring Default ZoningMerging Fabrics and Zoning Zone Merge Failure Recovery Using the Edit Zoning Window Edit Zoning Window Edit Zoning Window Tool Bar Buttons Managing Zone Sets Creating a Zone Set Removing a Zone from a Zone Set or from All Zone Sets Activating and Deactivating a Zone SetCopying a Zone to a Zone Set Removing a Zone Set Removing All Zoning Definitions Managing Zones Creating a Zone in a Zone Set Adding Zone Members Renaming a Zone or a Zone Set Removing a Zone MemberRemoving a Zone from a Zone Set Removing a Zone from All Zone Sets Creating an Alias Changing Zone TypesManaging Aliases Adding a Member to an Alias Removing an Alias from All Zones Factory User Accounts Account Name Password Admin Authority ExpirationManaging User Accounts Account Administration Add Creating User Accounts Account Administration Remove Removing a User Account Changing a User Account Password Account Administration Change Password Displaying Switch Information Faceplate Display Displaying Hardware Status Faceplate Display Chassis LED Cluster Switch Data Window Name Server Data WindowName Server Data Window Entries Entry Description Switch Data Window Entries Switch Data Window Entries Port Information Data Window Link Data WindowPort Statistics Data Window Configured Zonesets Data Window Configured Zonesets Data Window Configuring Alarms Alarm Threshold Configuration Dialog Sample Interval EventCount Paging a Switch Setting the Date and TimeSetting Temperature Thresholds Exporting Name Server Information to a File Type Description Resetting a SwitchSwitch Resets Configuring a Switch Switch Properties Symbolic Name Switch Administrative States 5describes the administrative state values Switch Administrative StatesDomain ID and Domain ID Lock Parameter Description Broadcast Support FC-SW-2 Compliance for Zoning Legacy Port Address Format Timeout ValuesTimeout Values Network Properties 11. Network Properties Dialog IP Configuration IP Configuration Parameters Snmp Configuration Snmp Configuration Parameters Remote Logging Snmp Trap ConfigurationSnmp Trap Configuration Parameters Archiving a Switch Restoring a Switch 12. Restore Dialogs Full and Selective Managing Switches Restoring a Switch Installing Firmware Managing Firmware Activating the Pending Firmware Changing the Pending Firmware Setting Value Restoring the Factory Default Configuration10. Factory Default Configuration Settings 10. Factory Default Configuration Settings Page Managing Ports Displaying Port Information Mode Description Monitoring Port StatusDisplaying Port Modes Port Modes Displaying Port Operational States Displaying Port SpeedsPort Operational States Port Speeds Displaying Transceiver Media Status Transceiver Media ViewPort Statistics Data Window Entries Media Icon Description LIP ALPD,ALPS Port Statistics Data Window Entries Port Information Data Window Entries Name Server Data Window Configuring Ports Port Properties Dialog Changing Port Administrative States Port Administrative States Changing Port Speeds Changing Port Modes Changing Buffer-to-Buffer Credits Extending Port Credits Stream GuardScan Device Resetting a Port Designate Donor Ports Testing Ports Port Loopback Test Dialog Managing Ports Testing Ports Command Line Interface Logging On to a Switch Keystroke Effect Command SyntaxTable A-1. Command-Line Completion Commands Table A-2. Commands Listed by Authority LevelUser Authority Commands Admin Authority Command Admin Session Commands Admin Command Syntax adminKeywords Examples Alias Command Syntax alias Rename aliasold aliasnew Members aliasRemove alias members Config Command Syntax configKeywords activate config Edit config Restore Archive function are not compatible with the Config RestoreCommand Save config # ftp symbolicname or ipaddress Keywords MMDDhhmmCCYY Date CommandSyntax date Fallback Command SyntaxAuthority Fallback Hardreset Command Syntax Help Command Keywords commandSyntax help command keyword Keyword History Command Syntax history Hotreset Command HotresetFabric is in the diagnostic operational state This command clears the event log and all counters Image Command Syntax image cleanupKeywords cleanup Unpack file Reinitializes the specified loop port Lip CommandAuthority Admin Syntax lip portnumber Keywords portnumber Passwd Command Syntax passwd accountname Keywords accountname Ping Command Syntax PingIpaddress Keywords ipaddress Ps Command Following is an example of the Ps commandSyntax Examples Displays current system process information Authority User Syntax quit, exit, or logout Quit CommandCloses the Telnet session Keywords config configname Reset CommandSyntax reset Parameter Default Table A-3. Switch Configuration DefaultsTable A-4. Port Configuration Defaults Table A-5. Alarm Threshold Configuration Defaults Table A-6. Zoning Configuration Defaults Table A-7. Snmp Configuration Defaults Table A-8. System Configuration Defaults Set Command Syntax set Port option Setup optionSwitch state Set Config Command Set configTable A-9. Set Config Port Parameters Port portnumber Send Arbff True instead of IDLEs Table A-10. Set Config Switch Parameters Compliant on page A-32. The default is Table A-11. Set Config Threshold Parameters Threshold Table A-12. Set Config Zoning Parameters Memory. Refer to FC-SW-2 Compliant on Arbff Following is an example of the Set Config Switch command Following is an example of the Set Config Threshold command Following is an example of the Set Config Zoning command Set Log Command Keywords archiveSet log Clear Save Level levelPort portlist Start StopStops logging of events Level keyword to Info at the same time Set Port Command EnableBypass alpa Speed transmissionspeed Set Setup Command Set setupTable A-13. Snmp Configuration Settings Snmp System Table A-14. System Configuration Settings Press Location Following is an example of the Set Setup System command SANbox2 admin # set setup system Show Command AlarmKeywords about Broadcast Log option Ns option Perf option Table A-15. Show Port Parameters LIPF8ALPS Support Post logSteering domainid Version TopologyUsers Following is an example of the Show Fabric command Following is an example of the Show NS local domain commandFollowing is an example of the Show NS domainID command Following is an example of the Show NS portID command Following is an example of the Show Interface command Collisions0 txqueuelen100 Following is an example of the Show Port command LIPF8F7 Following is an example of the Show Switch command Following is an example of the Show Topology command Command Line Interface Show Command Following is an example of the Show Version command Show Config Command Show config Following is an example of the Show Config Switch command Following is an example of the Show Config Threshold command Following is an example of the Show Config Zoning command Show Log Command Following is an example of the Show Log Options command Following is an example of the Show Log command Show Perf Command Errors portnumberFrame portnumber Inframe portnumber Following is an example of the Show Perf Byte command Keywords mfg Show Setup CommandShow setup Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Shutdown Command Authority Admin Syntax shutdown Test Command Syntax testKeywords port portnumber testtype Status Test port x internal Command Line Interface Test Command Syntax uptime Uptime CommandExamples The following is an example of the Uptime command User Command Displays all user accounts that exist on the switchKeywords accounts Add Following is an example of the User List command Following is an example of the User Add commandFollowing is an example of the User Delete command Whoami Whoami CommandFollowing is an example of the Whoami command Zone Command Syntax zone Members zone Remove zone membersRename zoneold zonenew Type zone zonetype Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zoneset Following is an example of the Zoneset List command Delete zonesetRemove zoneset zonelist Rename zonesetold zonesetnew Following is an example of the Zoneset Zones command Zoning Command Keywords activeEdit Opens a Zoning Edit session Following is an example of the Zoning Limits command Limits Following is an example of the Zoning List command E2JBOD2 Command Line Interface Zoning Command Command Line Interface Zoning Command 59022-06 a Graphing Port Performance Starting SANsurfer Fabric View Exiting SANsurfer Fabric View Figure B-3. Load Default Fabric File SANsurfer Fabric View Saving and Opening SANsurfer Fabric View Fabric View Files Setting SANsurfer Fabric View Preferences Figure B-5. Preferences SANsurfer Fabric View Setting the Polling Frequency Displaying Graphs Arranging Graphs in the Display Customizing Graphs Printing Graphs Saving Graph Statistics to a File Access Control List Zone Administrative StateBootP Class 2 Service Class 3 Service Configured Zone SetsDefault Visibility Fabric Management Switch Input Power LED Inter-Switch LinkMaintenance Mode Output Power LED Power On Self Test Post Principal SwitchPrivate Device Private Loop Index Index-2 59022-06 a 59022-06 a Index-3 Index-4 59022-06 a 59022-06 a Index-5 Index-6 59022-06 a 59022-06 a Index-7