Snmp Trap Configuration, Remote Logging | Q-Logic 8C/16 manual

4 – Managing Switches Configuring a Switch

Q

4.9.2.3

SNMP Trap Configuration

The SNMP trap configuration defines how traps are set. Choose from the tabs Trap1 – Trap 5 and configure the trap. Table 4-9describes the SNMP configuration parameters.

	Table 4-9. SNMP Trap Configuration Parameters

Parameter		Description

Trap Version		Specifies the SNMP version (1 or 2) with which to format traps.
Trap Enabled		Enables or disables the trap.
Trap Address1		Specifies the IP address to which SNMP traps are sent. A maximum
		of 5 trap addresses are supported. The default address for trap 1 is
		10.0.0.254. The default address for traps 2–5 is 0.0.0.0.
Trap Port1		The port number on which the trap is sent. The default is 162.
Trap Severity		Specifies a severity level to assign to the trap. Open the pull-down
		menu and choose a level. Traps must be enabled to access this pull-
		down menu. Trap severity levels include Unknown, Emergency,
		Alert, Critical, Error, Warning, Notify, Info, Debug, and Mark

1Trap address (other than 0.0.0.0) and trap port combinations must be unique. For example, if trap 1 and trap 2 have the same address, then they must have different port values. Similarly, if trap 1 and 2 have the same port value, they must have different addresses.

4.9.2.4

Remote Logging

The Remote Logging (syslog) feature enables saving of the log information to a remote host that supports the syslog protocol. When enabled, the log entries are sent to the syslog host at the IP address that you specify in the Logging Host IP Address field. Log entries are saved in the internal switch log whether this feature is enabled or not.

To save log information to a remote host, you must edit the syslog.conf file and then restart the syslog daemon. The syslog.conf file on the remote host must contain an entry that specifies the name of the log file in which to save error messages. Add the following line to the syslog.conf file. A <tab> separates the selector field (local0.info) and action field which contains the log file path name (/ var/adm/messages/messages.name).

local0.info <tab> /var/adm/messages.name

4-24	59022-06 A

Image 90

Q-Logic 8C/16 manual Remote Logging, Snmp Trap Configuration Parameters

Contents

SANbox2-8c/16 Switch Management User’s Guide SANbox2-8c/16 Switch Management User’s Guide Document Revision History Table of Contents Section Managing Fabrics Section Managing Switches Displaying Switch Information Section Managing Ports Appendix a Command Line Interface Command Syntax Appendix B Graphing Port Performance Glossary IndexInitial Startup Dialog SANbox Manager Window Menu Shortcut Keys Tool Bar Buttons Account Administration Add Account Administration RemoveTables Severity Levels Edit Zoning Window Tool Bar Buttons Port Administrative States Port Speeds Port Modes Intended Audience Related Materials Training Technical SupportAvailability Contact Information Installing SANbox Manager Management Workstation Requirements SANsurfer Management Suite Disk Windows Installation SANsurfer Management Suite Disk Linux Installation Enter the following command SANsurfer Management Suite Disk Solaris Installation SANbox2 Installation Disk Windows Installation SANbox2 Installation Disk Linux InstallationSANbox2 Installation Disk Solaris Installation „ For a Linux platform, enter the SANboxManager command „ For a Solaris platform, enter the SANboxManager commandStarting SANbox Manager SANbox Manager Window Save Default Fabric File Dialog SANbox Manager Exiting SANbox Manager Uninstalling SANbox Manager Changing the SANbox Manager Default Fabric File Password Saving and Opening SANbox Manager Fabric View Files Setting SANbox Manager Preferences Preferences Dialog SANbox Manager Using Online Help Viewing Software Version and Copyright Information SANbox Manager User Interface Topology DisplayFaceplate Display Switch Menu Bar Most menu selections have shortcut keys as shown in Table Menu Shortcut KeysShortcut Selection Tool Bar Tool Bar ButtonsTool Bar Button Description Fabric Tree Fabric Tree Working Status Indicator Graphic WindowData Window and Tabs Using the Topology Display Switch and Link Status Working with Switches and Links Selecting Switches and LinksArranging Switches in the Display Opening the Faceplate Display and Topology Popup Menus Topology Data Windows Using the Faceplate Display Port Views and Status Working with Ports Selecting PortsOpening the Faceplate Popup Menu Faceplate Data Windows User Authentication Security Inter-Switch Link Security Inband Management Managing the Fabric Database Adding a FabricChoose the Add Fabric button Removing a Fabric Opening a Fabric View FileSaving a Fabric View File Adding a New Switch to a Fabric Rediscovering a Fabric Replacing a Failed Switch Deleting Switches and Links Displaying Fabric InformationFabric Status Topology Display Switch and Status Icons Switch Icon Description Displaying the Event Browser Events Browser Severity Levels Severity Description Icon Filtering the Event Browser Filter Events Dialog Sorting the Event Browser Save the Event Browser to a File Active Zone Set Data Window Active Zone Set Data Window Zoning a Fabric Zoning ConceptsZones Access Control List Hard Zones Soft ZonesVirtual Private Fabric Hard Zones Aliases Zone Sets Zoning Configuration Zoning Database Using the Zoning Config Dialog Default VisibilityFC-SW-2 Auto Save Restoring Default Zoning Merging Fabrics and ZoningZone Merge Failure Zone Merge Failure Recovery Using the Edit Zoning Window Edit Zoning Window Edit Zoning Window Tool Bar Buttons Managing Zone Sets Creating a Zone Set Activating and Deactivating a Zone Set Copying a Zone to a Zone SetRemoving a Zone from a Zone Set or from All Zone Sets Removing a Zone Set Removing All Zoning Definitions Managing Zones Creating a Zone in a Zone Set Adding Zone Members Removing a Zone from a Zone Set Renaming a Zone or a Zone SetRemoving a Zone Member Removing a Zone from All Zone Sets Changing Zone Types Managing AliasesCreating an Alias Adding a Member to an Alias Removing an Alias from All Zones Account Name Password Admin Authority Expiration Managing User AccountsFactory User Accounts Account Administration Add Creating User Accounts Account Administration Remove Removing a User Account Changing a User Account Password Account Administration Change Password Displaying Switch Information Faceplate Display Displaying Hardware Status Faceplate Display Chassis LED Cluster Name Server Data Window Entries Switch Data WindowName Server Data Window Entry Description Switch Data Window Entries Switch Data Window Entries Link Data Window Port Statistics Data WindowPort Information Data Window Configured Zonesets Data Window Configured Zonesets Data Window Configuring Alarms Alarm Threshold Configuration Dialog Event CountSample Interval Setting Temperature Thresholds Paging a SwitchSetting the Date and Time Exporting Name Server Information to a File Resetting a Switch Switch ResetsType Description Configuring a Switch Switch Properties Symbolic Name Switch Administrative States Domain ID and Domain ID Lock 5describes the administrative state valuesSwitch Administrative States Parameter Description Broadcast Support FC-SW-2 Compliance for Zoning Timeout Values Timeout ValuesLegacy Port Address Format Network Properties 11. Network Properties Dialog IP Configuration IP Configuration Parameters Snmp Configuration Snmp Configuration Parameters Snmp Trap Configuration Snmp Trap Configuration ParametersRemote Logging Archiving a Switch Restoring a Switch 12. Restore Dialogs Full and Selective Managing Switches Restoring a Switch Installing Firmware Managing Firmware Activating the Pending Firmware Changing the Pending Firmware Restoring the Factory Default Configuration 10. Factory Default Configuration SettingsSetting Value 10. Factory Default Configuration Settings Page Managing Ports Displaying Port Information Displaying Port Modes Mode DescriptionMonitoring Port Status Port Modes Port Operational States Displaying Port Operational StatesDisplaying Port Speeds Port Speeds Port Statistics Data Window Entries Displaying Transceiver Media StatusTransceiver Media View Media Icon Description LIP ALPD,ALPS Port Statistics Data Window Entries Port Information Data Window Entries Name Server Data Window Configuring Ports Port Properties Dialog Changing Port Administrative States Port Administrative States Changing Port Speeds Changing Port Modes Changing Buffer-to-Buffer Credits Stream Guard Scan DeviceExtending Port Credits Resetting a Port Designate Donor Ports Testing Ports Port Loopback Test Dialog Managing Ports Testing Ports Command Line Interface Logging On to a Switch Command Syntax Table A-1. Command-Line CompletionKeystroke Effect User Authority Commands Admin Authority Command CommandsTable A-2. Commands Listed by Authority Level Admin Session Commands Keywords Admin CommandSyntax admin Examples Alias Command Syntax alias Members alias Remove alias membersRename aliasold aliasnew Keywords activate config Config CommandSyntax config Edit config Command RestoreArchive function are not compatible with the Config Restore Save config # ftp symbolicname or ipaddress Date Command Syntax dateKeywords MMDDhhmmCCYY Authority Fallback CommandSyntax Fallback Hardreset Command Syntax Syntax help command keyword Help CommandKeywords command Keyword History Command Syntax history Fabric is in the diagnostic operational state Hotreset CommandHotreset This command clears the event log and all counters Keywords cleanup Image CommandSyntax image cleanup Unpack file Lip Command Authority Admin Syntax lip portnumber Keywords portnumberReinitializes the specified loop port Passwd Command Syntax passwd accountname Keywords accountname Ipaddress Ping CommandSyntax Ping Keywords ipaddress Syntax Examples Ps CommandFollowing is an example of the Ps command Displays current system process information Quit Command Closes the Telnet sessionAuthority User Syntax quit, exit, or logout Reset Command Syntax resetKeywords config configname Table A-3. Switch Configuration Defaults Table A-4. Port Configuration DefaultsParameter Default Table A-5. Alarm Threshold Configuration Defaults Table A-6. Zoning Configuration Defaults Table A-7. Snmp Configuration Defaults Table A-8. System Configuration Defaults Set Command Syntax set Setup option Switch statePort option Table A-9. Set Config Port Parameters Set Config CommandSet config Port portnumber Send Arbff True instead of IDLEs Table A-10. Set Config Switch Parameters Compliant on page A-32. The default is Table A-11. Set Config Threshold Parameters Threshold Table A-12. Set Config Zoning Parameters Memory. Refer to FC-SW-2 Compliant on Arbff Following is an example of the Set Config Switch command Following is an example of the Set Config Threshold command Following is an example of the Set Config Zoning command Set log Set Log CommandKeywords archive Clear Level level Port portlistSave Stops logging of events StartStop Level keyword to Info at the same time Bypass alpa Set Port CommandEnable Speed transmissionspeed Table A-13. Snmp Configuration Settings Set Setup CommandSet setup Snmp System Table A-14. System Configuration Settings Press Location Following is an example of the Set Setup System command SANbox2 admin # set setup system Keywords about Show CommandAlarm Broadcast Log option Ns option Perf option Table A-15. Show Port Parameters LIPF8ALPS Post log Steering domainidSupport Topology UsersVersion Following is an example of the Show NS domainID command Following is an example of the Show Fabric commandFollowing is an example of the Show NS local domain command Following is an example of the Show NS portID command Following is an example of the Show Interface command Collisions0 txqueuelen100 Following is an example of the Show Port command LIPF8F7 Following is an example of the Show Switch command Following is an example of the Show Topology command Command Line Interface Show Command Following is an example of the Show Version command Show Config Command Show config Following is an example of the Show Config Switch command Following is an example of the Show Config Threshold command Following is an example of the Show Config Zoning command Show Log Command Following is an example of the Show Log Options command Following is an example of the Show Log command Frame portnumber Show Perf CommandErrors portnumber Inframe portnumber Following is an example of the Show Perf Byte command Show Setup Command Show setupKeywords mfg Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Shutdown Command Authority Admin Syntax shutdown Keywords port portnumber testtype Test CommandSyntax test Status Test port x internal Command Line Interface Test Command Uptime Command Examples The following is an example of the Uptime commandSyntax uptime Keywords accounts User CommandDisplays all user accounts that exist on the switch Add Following is an example of the User Add command Following is an example of the User Delete commandFollowing is an example of the User List command Whoami Command Following is an example of the Whoami commandWhoami Zone Command Syntax zone Rename zoneold zonenew Members zoneRemove zone members Type zone zonetype Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zoneset Remove zoneset zonelist Following is an example of the Zoneset List commandDelete zoneset Rename zonesetold zonesetnew Following is an example of the Zoneset Zones command Edit Zoning CommandKeywords active Opens a Zoning Edit session Following is an example of the Zoning Limits command Limits Following is an example of the Zoning List command E2JBOD2 Command Line Interface Zoning Command Command Line Interface Zoning Command 59022-06 a Graphing Port Performance Starting SANsurfer Fabric View Exiting SANsurfer Fabric View Figure B-3. Load Default Fabric File SANsurfer Fabric View Saving and Opening SANsurfer Fabric View Fabric View Files Setting SANsurfer Fabric View Preferences Figure B-5. Preferences SANsurfer Fabric View Setting the Polling Frequency Displaying Graphs Arranging Graphs in the Display Customizing Graphs Printing Graphs Saving Graph Statistics to a File BootP Access Control List ZoneAdministrative State Class 2 Service Default Visibility Class 3 ServiceConfigured Zone Sets Fabric Management Switch Maintenance Mode Input Power LEDInter-Switch Link Output Power LED Private Device Power On Self Test PostPrincipal Switch Private Loop Index Index-2 59022-06 a 59022-06 a Index-3 Index-4 59022-06 a 59022-06 a Index-5 Index-6 59022-06 a 59022-06 a Index-7