9.2PARALLEL INTERFACE SIGNALS
9.2.1COMPATIBILITY MODE
LCD Messages | Printer Status |
| Output Signal |
| |||
of Upper Line (English) |
| Busy | Select | nFault | PError | ||
|
|
|
|
|
|
|
|
ON LINE |
|
| In the online mode | L | H | H | L |
ON LINE |
|
| In the online mode (communicating) | L, H | H | H | L |
HEAD OPEN |
| The head was opened in the online mode. | H | L | L | L | |
PAUSE |
| **** | In a pause state | H | L | L | L |
ON LINE |
|
| Data was set from the host with the receive | H | H | H | L |
|
|
| buffer full. |
|
|
|
|
ON LINE |
|
| After data was sent from the host with the | L | H | H | L |
|
|
| receive buffer full, some data is processed |
|
|
|
|
|
|
| and room becomes available. |
|
|
|
|
ON LINE |
|
| Initialize process in execution (After the power | H | H | H | L |
|
|
| is turned on or the nInit signal is received) |
|
|
|
|
Display of error command | A command error has occurred in analyzing | H | L | L | L | ||
|
|
| the command. |
|
|
|
|
PAPER JAM | **** | A paper jam occurred during a paper feed. | H | L | L | L | |
CUTTER ERROR**** | An abnormal condition occurred at the cutter. | H | L | L | L | ||
NO PAPER | **** | The label has run out. | H | L | L | H | |
NO RIBBON | **** | The ribbon has run out. | H | L | L | H | |
HEAD OPEN | **** | A feed or an issue was attempted with the | H | L | L | L | |
|
|
| head opened. (except the [FEED] key) |
|
|
|
|
HEAD ERROR | **** | A broken dot error has occurred in the thermal | H | L | L | L | |
|
|
| head. |
|
|
|
|
EXCESS HEAD TEMP | The thermal head temperature has become | H | L | L | L | ||
|
|
| excessively high. |
|
|
|
|
RIBBON ERROR**** | An abnormal condition occurred in the sensor | H | L | L | L | ||
|
|
| for determining the torque for the ribbon |
|
|
|
|
|
|
| motor. |
|
|
|
|
REWIND FULL **** | An overflow error has occurred in the | H | L | L | L | ||
|
|
| rewinder. |
|
|
|
|
ON LINE |
|
| Ribbon near end state (Online) | L | H | H | L |
PAUSE |
|
| Ribbon near end state (In a pause state) | H | L | L | L |
ON LINE |
|
| Ribbon near end state (Operating) | L | H | H | L |
SAVING | #### &&&& | In writable character or PC command save | L | H | H | L | |
SAVING | %%%%%%% | mode |
|
|
|
| |
FLASH WRITE ERR. | An error has occurred in writing data into | H | L | L | L | ||
|
|
| memory for storage. |
|
|
|
|
FORMAT ERROR | An erase error has occurred in formatting | H | L | L | L | ||
|
|
| memory for storage. |
|
|
|
|
FLASH CARD FULL | Saving failed because of the insufficient | H | L | L | L | ||
|
|
| capacity of memory for storage. |
|
|
|
|
POWER FAILURE | A momentary power interruption has occurred. | H | L | L | L | ||
INITIALIZING... | The memory card for storage is being |
|
|
|
| ||
|
|
| initialized. (Initialization is carried out for a |
|
|
|
|
|
|
| max. of approximately 15 seconds) |
|
|
|
|
- 272 -
