LCD Messages of

LED Indication

 

 

Restoration

Acceptance

 

 

 

 

 

 

by the

of Status

 

 

 

 

 

 

No.

Upper line

 

 

 

 

Printer Status

[RESTART]

Request

POWER

ON LINE

ERROR

 

key

Reset

 

(English)

 

 

 

 

 

Yes/No

Command

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Yes/No

 

 

 

 

 

 

 

 

18

Display of error

{

z

{

A command error has occurred

Yes

Yes

 

command

 

 

 

in analyzing the command.

 

 

 

(See NOTE 1.)

 

 

 

 

 

 

 

19

POWER FAILURE

{

z

{

A momentary power interruption

No

No

 

 

 

 

 

has occurred.

 

 

20

INITIALIZING...

{

z

z

The memory card is being

 

 

 

 

 

initialized.

 

 

 

 

 

 

 

(Initialization is carried out for a

 

 

 

 

 

 

 

max. of approximately 15

 

 

 

 

 

 

 

seconds)

 

 

21

EEPROM ERROR

{

z

{

An EEPROM for back-up cannot

No

No

 

 

 

 

 

be read/written properly.

 

 

22

SYSTEM ERROR

{

z

{

When any abnormal operations

No

No

 

 

 

 

 

as below are performed, a

 

 

 

 

 

 

 

system error occurs.

 

 

 

 

 

 

 

(a)

Command fetch from an odd

 

 

 

 

 

 

 

 

address

 

 

 

 

 

 

 

(b) Access to the word data

 

 

 

 

 

 

 

 

from a place other than the

 

 

 

 

 

 

 

 

boundary of the word data

 

 

 

 

 

 

 

(c)

Access to the long word

 

 

 

 

 

 

 

 

data from a place other than

 

 

 

 

 

 

 

 

the boundary of the long

 

 

 

 

 

 

 

 

word data

 

 

 

 

 

 

 

(d) Access to the area of

 

 

 

 

 

 

 

 

80000000H to FFFFFFFFH

 

 

 

 

 

 

 

 

in the logic space in the user

 

 

 

 

 

 

 

 

mode.

 

 

 

 

 

 

 

(e)

Undefined command placed

 

 

 

 

 

 

 

 

in other than the delay slot

 

 

 

 

 

 

 

 

has been decoded.

 

 

 

 

 

 

 

(f) Undefined command in the

 

 

 

 

 

 

 

 

delay slot has been

 

 

 

 

 

 

 

 

decoded.

 

 

 

 

 

 

 

(g) Command to rewrite the

 

 

 

 

 

 

 

 

delay slot has been

 

 

 

 

 

 

 

 

decoded.

 

 

23

100BASE LAN

{

z

z

The 100BASE LAN is being

 

INITIALIZING...

 

 

 

initialized.

 

 

 

(This is spread over the

 

 

 

* When the B-9700-LAN-QM

 

 

 

upper and lower lines)

 

 

 

(built-in 10/100BASE Ethernet

 

 

 

 

 

 

 

interface board) has been

 

 

 

 

 

 

 

installed.

 

 

24

DHCP CLIENT

{

z

z

The DHCP client is being

 

INITIALIZING...

 

 

 

initialized.

 

 

 

(This is spread over the

 

 

 

* When the DHCP function is

 

 

 

upper and lower lines)

 

 

 

enabled.

 

 

- 275 -

Page 279
Image 279
Toshiba B-SX4T-GS20-QM-R manual LCD Messages LED Indication, Display of error, Yes Command, 275