5.2 LABEL ISSUE OPERATION

An example of the label issue operation is described below.

(1)Where the Saved Data Call Command is not used: Power ON

 

 

 

 

Place paper

 

 

 

 

 

 

[ESC] D:

Sets the label size.

 

 

 

 

 

 

 

 

 

Label Size Set Command

 

 

 

 

 

 

[ESC] AX: Adjusts the feed length, cut position, and

 

 

 

 

 

 

 

 

 

Position Fine Adjust Command

 

 

 

 

 

 

 

 

 

 

back feed length.

 

 

 

 

 

 

 

 

 

 

 

 

 

Print Density Fine

 

 

 

 

[ESC] AY: Adjusts the print density.

 

 

 

Adjust Command

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[ESC] T:

Feeds one sheet of paper and aligns it

 

 

 

Feed Command

 

 

 

 

with the first print position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[ESC] C: Clears the image buffer.

Image Buffer Clear Command

 

 

 

 

 

 

 

[ESC] LC: Sets the line format and draws it.

 

 

 

 

 

 

 

 

Line Format Command

 

 

 

 

 

 

[ESC] PC: Sets the bit map font format.

 

 

 

 

 

 

Bit Map Font Format Command

 

 

 

 

 

 

[ESC] PV: Sets the outline font format.

 

 

 

 

 

 

Outline Font Format Command

 

 

 

 

 

 

[ESC] XB: Sets the bar code format.

 

 

 

 

 

 

Bar Code Format Command

 

 

 

 

 

 

 

 

[ESC] RC: Draws bit map font data.

 

 

 

 

 

 

 

 

 

Bit Map Font Data Command

 

 

 

 

 

 

 

 

[ESC] RV: Draws outline font data.

 

 

 

 

 

 

Outline Font Data Command

 

 

 

 

 

 

[ESC] RB: Draws bar code data.

 

 

 

 

 

 

Bar Code Data Command

 

 

 

 

 

 

 

 

[ESC] XS: Issues (prints) the label.

 

 

 

 

 

 

 

 

 

 

 

Issue Command

 

 

 

 

 

 

 

 

 

 

 

Yes

 

 

 

 

 

 

 

 

 

 

<Change data issue>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Yes

 

 

No

 

 

 

<Format change>

 

 

 

 

 

 

 

 

 

 

 

 

 

Yes

 

No

 

 

<Label change>

 

 

 

 

 

 

 

 

 

 

 

 

 

 

No

Power OFF

NOTES: (1) When placing new paper, the Label Size Set Command and the Feed Command must always be sent. When using the same paper after the power is turned off and on, the Label Size Set Command and the Feed Command may be omitted.

(2)After the power is turned off and on, the Bit Map Font Format Command, the Outline Font Format Command, and the Bar Code Format Command should be sent as occasion demands because they are not protected in memory.

- 32 -

Page 36
Image 36
Toshiba B-SX4T-GS20-QM-R manual Label Issue Operation