For G700 Media Gateways | Avaya 555-233-116 guide

Music-on-hold

				J1
			J2	4
			J2	5
			4	5
			4
			5
				J3
				5
				2
				0051_0 PDH 062696
1.	Customer-supplied music source	5.	Power supply for universal coupler
2.	25-pair cable to analog line circuit pack	6.	103A or modular wall jack
3.	909A/B universal coupler	7.	4-pair modular cord
4.	Part of main distribution frame	8.	Tip and ring wires

Figure 47. Connections to nonregistered music-on-hold using analog line for an MCC1, SCC1, CMC1, or G600 Media Gateway

NOTE:

A wiring block must be locally engineered.

For G700 Media Gateways

On a G700 Media Gateway, the music-on-hold feature is connected through a port on an MM711 Analog Media Module.

The G700 Media Gateway does not support an auxiliary trunk circuit pack. Therefore, for internal communications controller (ICC) G700 Media Gateway users, the music-on-hold feature through an auxiliary trunk is not supported. However, external communications controller (ECC) G700 Media Gateway users can access the music-on-hold feature if their equipment is physically connected to a TN763 auxiliary trunk circuit pack in an EPN carrier of an ECC system.

NOTE:

ICC refers to MultiVantage Software running on an S8300 Media Server installed in, and acting as the primary controller for, a G700 Media Gateway.

ECC refers to MultiVantage Software running on an external S8700 Media Server within a G700 Media Gateway environment.

194 Issue 4 October 2002

555-233-116

Image 194

Avaya 555-233-116 manual For G700 Media Gateways

Contents

Release 1.2 555-233-116 Issue 4 October Copyright 2002, Avaya Inc All Rights Reserved Electromagnetic Compatibility EMC Standards SOC/REN European Union Declarations of Conformity Page Contents Extenders for 2-wire DCP endpoints External modems Terminal server installation 121 Definity Inads Malicious call trace 189 Music-on-hold 191 Multimedia communications Products MMCX, MMCH, ESM 207 Connector and cable pinout charts 231 Index 243 About this book Overview On next Internet Telephony Server-Enterprise Hardware Installation Conventions used in this book Systems and circuit packs Admonishments Antistatic protection Remove/install circuit packsPhysical dimensions Security Standards compliance Trademarks How to get this book on the WebLaser product Click Product Documentation How to get help Tell us what you think About this book Issue 4 October 555-233-116 909A/B universal coupler Typical 909A/B universal coupler BSY2/BY2 Typical modular jack pinout Auxiliary power supplies Local auxiliary power supply Applications that require auxiliary power Sources of auxiliary local power Required safety precautions 1145B power supply Circuit protection Installing the wall mounting Mountings 1146 mounting arrangement Installing the 1146 power distribution unit Installing and wiring the battery Installing the expanded power distribution unit Expanded power distribution unit Powering up and testing AC and DC power Power-supply LEDs LED Color Meaning Wire the 1146 power distribution unit Typical wiring to a terminal Replacing the batteries 1151A and 1151A2 power suppliesRepairing short circuits and resetting red LEDs Storing the batteries in inactive units Typical 1151A power supply front Standards compliance Desk mountingWall mounting Extenders for 2-wire DCP endpoints Wire DCP endpoints Typical connections to a 2-wire DCP workstation DCP extender, stand alone Typical DCP extender connections DCP extender, rack mount Data modules and asynchronous data Units Understanding RS-232 communications Installation procedure Typical connections to a data module Set hardware options Setting 7400A data module hardware optionsObtain required equipment Data module mode selector Setting 7400B data module hardware options Data module Down Connect data modules Connecting a single data module Connecting multiple data modules to the system Z77A data mounting Configuring the 7400A data module Using the 7400A menu system Powering up the 7400A Adjusting the control-panel display on the 7400A 7400A data module, EIA RS-232 interface circuits Data Signal Rate Select 2 DCE Source Input CI2 Setting interface options on 7400A DCE Select an option NEXT/NO or ENTER/YES Setting speed options on 7400A DCE Setting the automatic-answer feature on 7400A DCE Setting the break-disconnect option on 7400A DCE Configuring the RS-232 interface on 7400A DCE Setting parity on 7400A DCE Enabling remote loopback testing on 7400A DCE Configuring the ring indicator on 7400A DCE Enabling remote loopback on 7400A DCE Enabling test mode on 7400A DCE Exiting menus and saving changes on 7400A DCE Checking Definity administration on 7400A DCE Configuring the 7400A for modem pooling DTE applications Setting speed options on 7400A DTE SET AT CONTROL? Configuring the RS-232 interface on 7400A DTE CI2 CH2 ? ? Restoring factory defaults on 7400A DTE Test RESET? Local LOOP/ST? Selecting command mode on the 7400B Configuring the 7400B Data ModuleInstalling required configuration equipment for the 7400B Displaying the current configuration on the 7400B At &c1 &d2 q1 s0=1 &w0 &y0 where Configuring the 7400B for remote administrationRestoring factory defaults for the 7400B Setting the data speed for the 7400C Exiting command mode on the 7400BConfiguring the 7400C HSL high- speed link data module To change the existing speed, press NEXT/NO Setting other data options for the 7400C Configuring the 7400C for a dedicated private line Configuring the 7400D data module Recommended settings for typical configurations Accessing the menus of the 7400D Setting speed options for the 7400D Setting the automatic-answer feature on the 7400D Push the button indicated by the arrow Configuring the RS-232 interface of the 7400D CH = correctSetting? DCD = correctValue ? DTR = correctValue MSEC? SET LL DETECT? Sigls Disc = ON? Selecting 8400B options Configuring the 8400B Plus data moduleInstalling required configuration equipment for the 8400B + 2 + 16 = Configuring the ExpressRoute 1000 data module128 Administer the data modules Typical ExpressRoute 1000 data module connections Screen 1. Typical system-configuration listing Add data-module next Screen 2. Typical data-module form Asynchronous data units ADU Z3A2 ADU Hardware required when configuring modems External modems Paradyne Comsphere Configuring the 3715 for CMSConfiguring the 3715 for modem pooling Paradyne Comsphere 3810 Plus Configuring the 3810 Plus and 3811 Plus modemsATY0S10=100S78=2M0E0\N1&W The modem is now configured AT&F&D2&S4\D3S2=128x7V2S7=60S85=1 Configuring the 3910 for CMS Understanding the modem controls and displays Loading the copied default settings Creating an editable configuration setCopying factory default settings Press F1 to select Choose Function Configuring the RS-232 DTR and DSR ready signals Configuring the DTE interfaceConfiguring basic, RS-232 handshaking Finishing configuration of the DTE interface Configuring RS-232 RTS and CTS send signalsConfiguring various control features Skipping to the result-code options Configuring the DTE dialerOpening the DTE Dialer menus Disabling result codes Configuring the data lineSetting the line rate Exiting the DTE Dialer menu Exiting the dial line menu Saving the new configurationV22b Guard Tone Disable menu heading appears Dial Tx Level Permissv -9 menu heading appears Checking the status of the Comsphere 3910 modem Configuring U.S. Robotics modemsRobotics modems Accessing the administration form AdministrationConfiguring the MT5634ZBA-USB modem Multi-Tech MT5634ZBA-USB Set the Auto-Answer Ring Number field to S0=10 Setting data-transmission parametersSetting dialing parameters Setting additional, modem-specific parameters Exiting the form and saving the changes Task list Connecting printers using TCP/IPPrinters PMS journal and PMS log printers Administering adjunct parametersTesting the switch-to-adjunct link System printer Setting up the PC Setting up an RSP configurationSetting up the switch Downloading RSP Installing RSPAdministering RSP How the DLG application works What is the Definity LAN gateway?Definity LAN gateway system7 How is the DLG application is packaged Mapd DLG Switch-based connectivity co-resident DLG Co-resident DLG Definity LAN gateway system Issue 4 October 555-233-116 Terminal server installation Switch-to-adjunct LAN connectivity through a terminal server Installing and administering the terminal server Distance limits Cabling diagram Making the connections Administering the IOLAN+ Navigating the IOLAN+ terminal server Setting up HyperTerminal on the computerAdministering the IOLAN+ the first time Select Admin mode Password and press Enter Administration Menu Rebooting the IOLAN+ Reboot Reboot Server Administering the gateway Administering an IOLAN+ port Name port number or other descriptive name Testing Type change node-names ip and press Return Administering IP node namesPotential failure scenarios and repair actions Administering IP services Node Names Session Layer Terminal server installation Issue 4 October 555-233-116 With a smart jack Installing a loopback jackDS1/T1 CPE loopback jack9 Without a smart jack Testing the DS1 span from the Icsu to the loopback jack Administering the loopback jackLoopback testing with a smart jack Checking the integrity of local equipment Administering the DS1 for the testTesting the integrity of the loopback circuit Busying out the DS1 circuit pack Testing the integrity of data sent over the loop Clearing the results of previous tests Jack field is Pattern 3-in-24 Running the data testValue of the Test cpe-loopback Condition Solution Restoring DS1 administration ConditionSolution Releasing the DS1 circuit pack Page Network interface at smart jack for a 120A2 or later Icsu Prdfcs7a KLC 555-233-116 Issue 4 October 2002 Prdfcs4a KLC 555-233-116 Issue 4 October 2002 Prdfcs5a KLC Testing a loopback jack without a smart jack Network interface at dumb block for a 120A2 or later Icsu Prdfcs8a KLC 555-233-116 Issue 4 October 2002 Prdfcs6a KLC Page Configurations using fiber multiplexers Isdn converters and adapters10 Converters for single-carrier cabinets PRI-to-DASS and PRI-to-DPNSS converters PRI-to-BRI converter Typical PRI to BRI converter cabling Converters for multi-carrier cabinets Converters for multi-carrier cabinets Isdn converters and adapters Issue 4 October 555-233-116 Stratum 3 clock Set clock options ST3 clock board option switch settings Switch Status/Results Cabling the Stratum 3 clock Typical connections to Stratum 3 clock BL-W/2 Stratum 3 clock wiring installation procedureBL/1 Bclkrtn ALRM5B Bclklst ALRM5A Bpwrrtn RREF1 EXTSYN1R CCA02R Busy tone disconnect equipment for Non-U.S. installations12 Typical cabling for busy tone disconnectPage Call detail recording CDR option Settings Connecting CDR equipment Connecting a CDR device Using other equipment as the CDR output devicesSources of administration information Administering CDR parameters Connecting a CDR device CDR System Parameters screen appears ‘‘Downloading RSP’’ ‘‘Installing RSP’’ ‘‘Administering RSP’’ Downloading RSP Page Definity INADS14 Analog loopback Analog loopback connections Type change system-parameters maintenance and press Enter AdministrationPartner installation Type add term-ext-group number or next and press Enter Inads connection with power fail transfer Check local regulations regarding this connection method Standard reliability Inads connection European platform Inads connection without power fail transfer High reliability European platform connection Normal connectionAtlas/Spain platform connection Set automatic line selection outgoing trunk all platforms Definity ECS administrationSet Partner CO line port all platforms Set incoming line ringing all platforms Example of an ART script file Installation test all installationsConnectivity for Inads on S8700 S8300 media servers Issue 4 October 555-233-116 Malicious call trace15 Malicious call tracePage Music-on-hold For MCC1, SCC1, CMC1, and G600 Media Gateways Registered music source Nonregistered music sourcePage For G700 Media Gateways For G700 Media Gateways Music-on-hold Issue 4 October 555-233-116 Paging and announcement Equipment Background information IP configurations IP trunk IP solutions mode LAN Configuration using the S8700 Media Server with IP connect Multi-site environment S8700 Media Server with IP connect Loudspeaker paging without paging adapter Loudspeaker paging access without universal coupler Loudspeaker paging with universal coupler Espa radio paging Typical Espa radio paging connections Queue warning indicator External ringing Loudspeaker paging for G700 Media Gateways Multimedia communications Products MMCX, MMCH, ESM18 Masi for Mmcx Direction connection Modular jack pin assignment Main distribution frame connection Nonsignaling configurationWideband endpoints Signaling configuration Typical nonsignaling wideband configuration Typical signaling wideband configuration Multimedia call handling Mmch Connect the endpoints Typical multimedia call handling connections Administer one number complex Administer the systemAdminister the endpoints Setup and test the Mmch installation Configuring the PictureTel PCS50 Live 50 and PCS100 Double click on the PictureTel Live Configure icon How to place a PictureTel video call Troubleshooting PictureTel ProShare configuration Select restart windows How to place a ProShare video call Troubleshooting ProShare Vistium configuration Zydacron configuration How to place a Zydacron video call Place conversion test call Troubleshooting ZydacronExpansion services module ESM installation Typical multimedia call handling ESM connections Place test call TroubleshootingStatus esm Status signaling-group List MMI Issue 4 October 555-233-116 Connecting the property management system PMS Property management system PMS Connecting a terminal and/or journal printer Using data modules Connecting PMS and printers using TCP/IP PMS, PMS journal, and PMS log printers Using the downloadable reliable session-layer protocol tool Downloading RSP Connector and cable pinout charts BR-R Plug DS1 interface Cable H600-307 50-Pin 15-Pin Color Designation TXT.1 PXR.7 BR-BK 210 311 211 312 212 313 BR-V Cenab TXR.1 CP2SCLK TXR.4 Sclk TXT.7 Page Index Numerics Index 121 Index