OL-17467-02 | Cisco Systems MDS 9500 Series specs

Chapter 2 Installing the Cisco MDS 9500 Series

Removing and Installing a Power Supply or PEM

Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m .

Step 2 Ensure that the system (earth) ground connection has been made. See the “System Grounding” section on page 2-17.

Step 3 Grasp the power supply handle with one hand, place your other hand underneath the power supply, and slide the power supply into the power supply bay, ensuring that it is fully seated in the bay.

Step 4 Tighten the captive screw on the power supply to 8 in-lb.

Step 5 Remove the two screws securing the terminal block cover and slide the cover off of the terminal block.

Note Use 90°C copper conductors for North American installations.

Step 6 Loosen the screws inside the terminal block and attach the DC cables to the screws. The wire must be copper, and sized per local and national installation requirements.

Step 7 Connect the DC cables to the terminal block in the following order:

•Ground

•Negative (-)

•Positive (+)

Warning When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046

Caution The DC return connection (Negative (-)) to this system is to remain isolated from the system frame and chassis (DC-I).

Step 8 Reinstall the terminal block cover after ensuring that all cable connections are secure and tighten the screws holding the terminal block to the power supply.

Caution Reinstall the terminal block cover to prevent a short circuit or shock hazard.

Caution In a system with dual power supplies, connect each power supply to a separate source. In case of a line failure, the second source will most likely still be available.

Step 9 Remove the tape from the circuit breaker switch handle and provide power by moving the handle to the on () position.Turning the power switch on also locks the power supply in the chassis.

Step 10 Verify power supply operation by checking that the power supply LEDs are in the following states:

•INPUT OK LED is green.

•FAN OK LED is green.

•Output fail LED is off.

		Cisco MDS 9500 Series Hardware Installation Guide
		Cisco MDS 9500 Series Hardware Installation Guide
	OL-17467-02			2-63
	OL-17467-02			2-63

Image 143

Cisco Systems MDS 9500 Series manual OL-17467-02

Contents

Americas Headquarters Cisco MDS 9500 Series Hardware Installation GuidePage N T E N T S Port Index Availability Removing and Installing a Crossbar Module Installing an AC Power Supply in the Cisco MDS 9513 Director Cabinet and Rack Installation C-1 Chassis Console Port E-2 COM1 Port E-3 Feature Description Release Where Documented Fips SFP+ Cisco MDS 9216i and 9216A Switches Switching Module offers 48 autosensing 1Switching Module offers 24 autosensing 1 Switching Module can be used in any of the Cisco Port IP Provided Fcip services and iSCSI 34a 3000W Power Added 3000W power supply forChannel Services Module SSM Installation Modules Specific Cwdm SFP SFP Xiv Chapter Title Description AudienceOrganization Appendix F Provides a site-planning checklist and sample maintenanceConventions Appendix E Xvii Release Notes Regulatory Compliance and Safety InformationHardware Installation Related Documentation Cisco Fabric Manager Command-Line InterfaceTroubleshooting and Reference Installation and Configuration Note Preface Product Overview Chassis Cisco MDS 9513 Director Cisco MDS 9513 Chassis Front Panel View Rear Panel 9513 Chassis Cisco MDS 9509 Director Cisco MDS 9506 Chassis Cisco MDS 9506 Director Status Description Backplane and Clock ModulesLower LEDs Upper LEDs Power Supplies Cisco MDS Fibre Channel Switch for IBM Blade Center Power supply switch Power Supply LEDs AC power connection Cisco MDS 9513 Power Supplies Output Fail FAN OK 4000-W AC Power Supply for the Cisco MDS 9509 Director Cisco MDS 9509 Power Supplies 3000-W AC Power Supply for the Cisco MDS 9509 Director 2500-W AC Power Supply for the Cisco MDS 9509 Director 11 Cisco MDS 9506 Power Supply 1900-W AC or DC Cisco MDS 9506 Power Supplies Supervisor Modules Fan Modules 12 Cisco MDS 9500 Series Supervisor-2 Module Supervisor-2 Modules Memory Bytes Control and ManagementProcessor Port Interfaces 13 Supervisor-2 Module LEDs LEDs on the Supervisor-2 Module LED MgmtGreen Link is up 10/100/1000 Off No link Ethernet Link 14shows a Cisco MDS 9500 Series Supervisor-1 module Supervisor-1 Modules Crossbar Switching Fabric 15 Supervisor-1 Module LEDs LEDs on the Supervisor-1 Module LEDs for the Cisco MDS 9500 Series Supervisor Modules 16 Crossbar Module LEDs Crossbar Modules LEDs for the Cisco MDS 9500 Crossbar Modules Module 9513 9509 9506 9222i 9216A 9216i Cisco MDS 9000 Series Module Compatibility SSM Port Index AvailabilityModule Physical Ports Port Indexes Allocated Example 1-1 Borrowing Port Indexes from Another Slot Supervisor Module Port Index Requirements Port 4-Gbps Fibre Channel switching module Supervisor-1 Physical Port Slot No Modules in Cisco MDS 9513 Director Port 4-Gbps Fibre Channel switching module Supervisor-2Physical Port Slot No Modules in Cisco MDS 9509 Director Ports Indexes Generation 1 modules Switching ModulesGeneration 2 modules Port 8-Gbps Host-Optimized Fibre Channel Switching Module Port 8-Gbps Fibre Channel Switching Module Link LEDs Port 4-Gbps Fibre Channel Switching Module Status LED Link LEDs Fibre Channel ports Status LED Fibre Channel ports Link LEDs Port group Status LED Link LED X2 port interfaces Port 10-Gbps Fibre Channel Switching Module Port 2-Gbps Fibre Channel Switching Module LEDs on the Generation 2 Switching Modules 25 Cisco MDS 9000 Family 32-Port 2-Gbps Switching Module Switching Module Features LEDs on the Generation 1 Switching Module 18/4-Port Multiservice Module Services Modules 27shows the MSM-18/4 module 15describes the LEDs for the 18/4-port Multiservice module LEDs on the 18/4-Port Multiservice Module 14/2-Port Multiprotocol Services Module 16describes the LEDs for the MPS-14/2 modules LEDs on the MPS-14/2 Module Status LED Link LEDs Gigabit Ethernet ports Asset tag IP Storage Services Modules 17describes the LEDs for the IPS services modules LEDs on IP Storage Services Modules 31shows the Fibre Channel ASM Port Fibre Channel Advanced Services Module 18describes the LEDs for the ASM LEDs on the Fibre Channel Advanced Services Modules 32shows the SSM Port Fibre Channel Storage Services Module 19describes the LEDs for the Storage Services Modules LEDs on the Storage Services Modules 33shows the CSM Caching Services Module Disk drive Battery 20describes the LEDs for the CSM LEDs on the Caching Services Module X2 Transceivers Supported Transceivers Gigabit Ethernet SFP Transceivers Fibre Channel SFP TransceiversCombination Fibre Channel/Gigabit Ethernet SFP Transceivers Dwdm Fibre Channel SFP Transceivers Product Overview Supported Transceivers Installing the Cisco MDS 9500 Series This section provides the following topics PreinstallationInstallation Options Installation Guidelines Installing the Cisco MDS 9500 Series Preinstallation Required Equipment Unpacking and Inspecting the Switch Installing the Chassis in a Cabinet or Rack Quantity Part Description Installing the Cisco MDS 9513 Director in a Rack Positioning the Rack-Mount Support Brackets Positioning the Support Bars Securing the Rack-Mount Support Brackets Screws, 12-24 or Mounting rail Support bracket Cable guide Installing the Cisco MDS 9509 Director in a Rack Side rack-mount brackets 12-24 x 3/4-inch Phillips binder-head screws10-32 x 3/4-inch Phillips binder-head screws M3 x 8-mm Phillips pan-head screws Front of rack Crossbar Mounting rail Installing the Cisco MDS 9509 Chassis in the Rack Installing the Cisco MDS 9506 Director in a Rack M4 x 6-mm Phillips pan-head screws 12-24 x 3/4-in. Phillips binder-head screws10-32 x 3/4-in. Phillips binder-head screws Proper Grounding Practices System Grounding Environment Level Grounding Recommendations Preventing Electrostatic Discharge Damage Cisco MDS 9500 Series Hardware Installation Guide 133947 Required Tools and Equipment Establishing the System Ground Grounding the Chassis 144510 12 ESD Ground Location on the Cisco MDS 9513 Chassis Rear ESD plug ESD socket 13 System Ground Location on the Cisco MDS 9509 Chassis 14 System Ground Location on the Cisco MDS 9506 Chassis This section provides the following information Starting Up the SwitchConnecting the Power Supplies 15 Cable Retention on the Power Supply 16 2500-W AC Power Supply for the Cisco MDS 9509 Director 18shows an AC PEM for a Cisco MDS 9506 Director Captive screws AC power connection PEM switch 19 Power Supply for Cisco MDS 9506 Director 20shows the 2500-W DC power supply Statement 21 DC PEM for a Cisco MDS 9506 Director Powering Up the Switch and Verifying Component Installation Installing the Cisco MDS 9500 Series Starting Up the Switch This section provides the following information Removing Supervisor Modules Installing Supervisor Modules 22 Positioning a Module in the Chassis Slot guides EMI Gasket 23 Clearing the EMI Gasket 24 Closing the Ejector Levers Removing a Caching Services Module Removing Other Switching and Services Modules Cisco MDS 9500 Series Hardware Installation Guide Removing and Installing a Crossbar Module 25 Captive Screws and Ejector Levers on the Crossbar Module 26 Installing the Crossbar Module Tighten the two captive screws on the module to 8 in-lb Maintaining a Caching Services ModuleMaintaining the Batteries on the Caching Services Module Maintaining the Disk Drives on the Caching Services Module Removing and Installing a Power Supply or PEM Removing an AC Power Supply from the Cisco MDS 9513 Director 28 Handling a Power Supply for the Cisco MDS 9513 Director Installing an AC Power Supply in the Cisco MDS 9513 Director 29 AC Power Supply for the Cisco MDS 9513 Director Removing an AC Power Supply from the Cisco MDS 9509 Director Installing an AC Power Supply in the Cisco MDS 9509 Director 31 4000-W AC Power Supply for the Cisco MDS 9509 Director 32 3000-W AC Power Supply for the Cisco MDS 9509 Director 33 2500-W AC Power Supply for the Cisco MDS 9509 Director DC power supply for the Cisco MDS 9509 Director is 2500 W Removing a DC Power Supply from the Cisco MDS 9509 Director Installing a DC Power Supply in the Cisco MDS 9509 Director OL-17467-02 Removing a DC PEM Removing an AC PEM 35 Connecting or Disconnecting the DC PEM Installing a DC PEM Installing an AC PEM 36 Handling a Power Supply for the Cisco MDS 9506 Director Removing and Installing Fan Modules This section includes the following topics Removing a Front Fan Module on the Cisco MDS 9513 Director Installing a Front Fan Module on the Cisco MDS 9513 Director Removing the Crossbar Module Fan Tray 38 Removing a Crossbar Module Fan Tray Installing the Crossbar Module Fan Tray Removing a Front Fan Module on the Cisco MDS 9509 Director Installing a Front Fan Module on the Cisco MDS 9509 Director Removing a Front Fan Module on the Cisco MDS 9506 Director Installing a Front Fan Module on the Cisco MDS 9506 Director Removing a CompactFlash Card Removing and Installing CompactFlash Cards Disposable ESD wrist strap Removing and Installing Clock ModulesInstalling a CompactFlash Card Cisco MDS 9513 clock module Removing a Clock Module from the Cisco MDS 9513 Director Repeat and to remove any additional clock modules 42 Clock Module for the Cisco MDS 9513 Director Installing a Clock Module into the Cisco MDS 9513 Director M3 x 6-mm Phillips pan-head screws Removing a Clock Module from the Cisco MDS 9509 DirectorCisco MDS 9509 clock module OL-17467-02 Connectors Clock module Cisco MDS 9506 clock module Installing a Clock Module into the Cisco MDS 9509 DirectorRemoving a Clock Module from the Cisco MDS 9506 Director 120093 Connector Installing a Clock Module into the Cisco MDS 9506 Director Overview Generation 3 Module Fabric Module Software Release Usage Guidelines Before You Begin Upgrading the MDS 9513 Director Migration Procedures for the MDS 9513 Director CLI Configuration Guide Switch# out-of-service xbar Damage section on 188730 Slot Figure A-2 Installing a Fabric Module Switch# show module xbar Figure A-3 Strategy 2 Migration Process Flow Switch# show hardware fabric-mode Mod World-Wide-Names WWN 10.182 304 OL-17467-02 Cisco MDS 9500 Series Hardware Installation Guide Connecting the Cisco MDS 9500 Series Preparing for Network Connections Connecting to the Console Port 91701 Connecting to the COM1 Port 99272 Connecting to the Mgmt 10/100/1000 Ethernet Port Connecting to the Mgmt 10/100 Ethernet Port 99328 Removing and Installing X2 Transceivers Connecting to a Fibre Channel Port Figure B-5 Cisco MDS 9000 Family X2 Transceivers Removing an X2 Transceiver Installing an X2 Transceiver Removing an SFP Transceiver Removing and Installing SFP Transceivers 115237 Removing a Cable from an SFP Transceiver Removing and Installing Cables into SFP TransceiversInstalling an SFP Transceiver Installing a Cable into an SFP Transceiver Maintaining SFP Transceivers and Fiber-Optic Cables General Requirements for Cabinets and Racks Cabinet and Rack Requirements Cabinet and Rack Requirements for the Cisco MDS 9513 Chassis Panduit Corporation Requirements Specific to Perforated Cabinets Rittal Corporation Requirements Specific to Solid-Walled Cabinets Requirements Specific to Standard Open Racks Requirements Specific to Two-Post Telco Racks Cisco MDS 9000 Family Telco and EIA Shelf Bracket EIA 4-Post Before Installing the Rack-Mount Support BracketsRack-Mounting Guidelines MDS Rack Type MDS 9216A Required Equipment Before Installing the Shelf Brackets Installing the Shelf Bracket Kit into a Two-Post Telco Rack Figure C-2 Installing the Shelf Bracket Kit into an EIA Rack Installing the Shelf Bracket Kit into a Four-Post EIA Rack Installing the Switch on the Rack-Mount Support Brackets Removing the Shelf Bracket Kit Optional Installing the Switch on the Shelf Brackets Cisco MDS 9500 Shelf Bracket Clip nuts 20 x 3/4 in. Phillips pan-head screws with lock washers10-32 x 1/3 in. Phillips pan-head screws with lock washers Figure C-3 Installing the Shelf Bracket Kit into a Rack Installing the Switch on the Shelf Brackets Description Specification Switch Specifications Appendix D Technical Specifications Switch Specifications Table D-3 Physical Characteristics Module Specifications Module Weight Weight of Modules Attribute Value Power Specifications for the Cisco MDS 9513 DirectorSpecifications for the Cisco MDS 9513 Power Supplies Table D-8 Specifications for Cisco MDS 9513 Power Supplies Release Watts BTU/hr Amps AC Power Consumption for the Cisco MDS 9513 DirectorPower Heat Input Current Module Type Required Dissipation 90 VAC 120 VAC 180 VAC 240 VAC Module Type / Product Number Power Specifications for the Cisco MDS 9509 DirectorSpecifications for the Cisco MDS 9509 Power Supplies DC Power Supply NX-OS SAN-OS DS-X9304-SMIP DS-X9308-SMIP220 940 Port IPS module 160 683 220 1000 Port IPS module 160 728 Power HeatModule Type Required Dissipation 48 VDC 60 VDC SAN-OS Release Watts BTU/hr Amps AC Power Consumption for the Cisco MDS 9509 Director Power Specifications for the Cisco MDS 9506 Director VDC Specifications for the Cisco MDS 9506 Power Supplies NX-OS SAN-OS Cisco MDS 126 573 Chassis with fan module DS-C9506 VDC amps 200 910 DS-X9560-SMC 210 955 AC Power Consumption for the Cisco MDS 9506 Director X2 Transceiver Specifications Average Transmit Average Receive Power dBmCisco 10-Gbps Fibre Channel X2 Transceivers Transceiver Module Product Number Description Type Operating Storage Cisco 10-Gbps Ethernet X2 Transceivers Cisco 10-Gbps Ethernet Dwdm X2 Transceiver SFP and SFP+ Transceiver Specifications Cisco Fibre Channel SFP and SFP+ Transceivers 125 Miles 10 km 250 500 Average Transmit Average Receive Power dBmWavelength Core Size Baud Rate Cable Distance Fiber Type Micon GBd Meter Safety Information for the Cisco MDS 9000 Family DBm 10.0 Micron 62 50 micron OM2 Power dBm DBmNanometer Fiber Type Micon GBd Meter 0625 Miles 10 km 125 DS-SFP-FCGE-LW Parameter Symbol Min Max UnitStorage temperature Case temperature Relative humidity Cisco Fibre Channel and Gigabit Ethernet Transceivers 11.0 19 GE Power dBm Fiber Loss Budget dBm10.0 FC 17 GE FC 62.5 micron FC 50.0 micron GE 62.5 micron Description Color Cisco Cwdm SFP Transceivers All Cisco 2-Gbps 40C 85C 1450 1620 Input Wavelength Transmitter Parameters Symbol Minimum Typical Maximum UnitsSmsr Suppression Ratio Transmitter Optical All Cisco 4-Gbps 40C 85C DS-SFP-GE-T Cisco Gigabit Ethernet TransceiversCisco Dwdm SFP Transceivers Transceiver Module Product Number Description OL-17467-02 Cisco MDS 9500 Series Hardware Installation Guide Cables and Adapters Provided Cable and Port Specifications Console Pin SignalConsole Port Console Port Pinouts DCD COM1 PortCOM1 Port Pinouts CTS DSR DCD Connecting the COM1 Port to a ModemMgmt 10/100/1000 Ethernet Port DB-9F/RJ45F RJ-45 Not used TD+RD+ Mgmt 10/100 Ethernet Port Figure E-3 RJ-45 Interface Cable Connector Power Cords Supported Power Cords and Plugs MDS MDS 9509 2500W Power SupplyLength Description Feet Meters USA 94973 United Kingdom BS89/13, BS 1363/A 13 a replaceable fuse Supported Plugs for the 4000-W AC Power Supply Jumper Power Cord Power Cord Power Supply AC Power Cords CAB-9K20A-NA AC Power Cord Illustrations CAB-9K16A-AUS CAB-9K16A-EU OL-17467-02 Contacting Customer Service Site Planning and Maintenance Records Figure F-1 Serial Number Location on Cisco MDS 9513 Director Finding the Chassis Serial Number Figure F-2 Serial Number Location on Cisco MDS 9509 Director Task No Planning Activity Verified By Time Date Site Preparation Checklist Task No Planning Activity Verified By Time Date Contact and Site Information Slot Module Type Module Serial Number Supervisor Chassis and Module Information Slot Module Type Module Serial Number Supervisor Providing MDS 9509 Director Port 8-Gbps Fibre Channel switching modules descriptionBladeswitch Removing from MDS 9506 Director procedure Installing in a rack procedure Power supplies Mesh design Supervisor-2 modules Supervisor-2 modules table Figure B-15 LEDs ASM table Clock modules Removing clock modules procedure Installing in a rack procedure Power supply LEDs table MDS 9509 Director LEDs table CSM Power supplies MDS 9509 DirectorLEDs LEDs table MDS 9506 Director LEDs table Dwdm Description Generation 1 modules InstallingASM CSM Cwdm IN-8 IN-9 CSM IN-11 Nebs IN-13 SSM IN-15 IN-16