Mgmt, Led | Cisco Systems MDS 9500 Series specification

Chapter 1 Product Overview

Supervisor Modules

Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m .

Table 1-4	LEDs for the Cisco MDS 9500 Series Supervisor-2 Modules

LED		Status	Description

Status		Green	All diagnostics pass. The module is operational
			(normal initialization sequence).

		Orange	One of the following occurs:
			• The module is booting or running diagnostics
			(normal initialization sequence).
			• An over-temperature condition occurred (a minor
			threshold was exceeded during environmental
			monitoring).

		Red	One of the following occurred:
			• The diagnostic test failed. The module is not
			operational because a fault occurred during the
			initialization sequence.
			• An over-temperature condition occurred (a major
			threshold was exceeded during environmental
			monitoring).

System		Green	All chassis environmental monitors are reporting OK.

		Orange	One of the following occurred:
			• The power supply failed or the power supply fan
			failed.
			• Incompatible power supplies are installed.
			• The redundant clock failed.

		Red	The temperature of the supervisor module exceeded
			the major threshold.

Active		Green	The Supervisor-2 module is operational and active.

		Orange	The Supervisor-2 module is in standby mode.

Power		Green	Sufficient power is available for all modules.
Management
Management		Orange	Sufficient power is not available for all modules.
		Orange	Sufficient power is not available for all modules.

MGMT		Green	Link is up.
10/100/1000
10/100/1000		Off	No link.
Ethernet Link		Off	No link.
Ethernet Link
LED

MGMT 10/100		Green	Traffic is flowing through port.
Ethernet
Ethernet		Off	No link or no traffic.
Activity LED		Off	No link or no traffic.
Activity LED

CompactFlash		Green	The external CompactFlash card is being accessed.

		Off	No activity.

	Cisco MDS 9500 Series Hardware Installation Guide
1-20	OL-17467-02

Image 42

Cisco Systems MDS 9500 Series manual Mgmt, Green Link is up 10/100/1000 Off No link Ethernet Link, Led

Contents

Cisco MDS 9500 Series Hardware Installation Guide Americas HeadquartersPage N T E N T S Port Index Availability Removing and Installing a Crossbar Module Installing an AC Power Supply in the Cisco MDS 9513 Director Cabinet and Rack Installation C-1 Chassis Console Port E-2 COM1 Port E-3 Feature Description Release Where Documented SFP+ Fips Switching Module can be used in any of the Cisco Switching Module offers 48 autosensing 1Switching Module offers 24 autosensing 1 Cisco MDS 9216i and 9216A Switches Installation Modules Specific 3000W Power Added 3000W power supply forChannel Services Module SSM Port IP Provided Fcip services and iSCSI 34a SFP Cwdm SFP Xiv Audience OrganizationChapter Title Description Appendix E Provides a site-planning checklist and sample maintenanceConventions Appendix F Xvii Related Documentation Regulatory Compliance and Safety InformationHardware Installation Release Notes Installation and Configuration Note Command-Line InterfaceTroubleshooting and Reference Cisco Fabric Manager Preface Product Overview Chassis Cisco MDS 9513 Director Cisco MDS 9513 Chassis Front Panel View Rear Panel 9513 Chassis Cisco MDS 9509 Director Cisco MDS 9506 Director Cisco MDS 9506 Chassis Backplane and Clock Modules Lower LEDs Upper LEDsStatus Description Cisco MDS Fibre Channel Switch for IBM Blade Center Power Supplies Cisco MDS 9513 Power Supplies Power supply switch Power Supply LEDs AC power connection FAN OK Output Fail Cisco MDS 9509 Power Supplies 4000-W AC Power Supply for the Cisco MDS 9509 Director 3000-W AC Power Supply for the Cisco MDS 9509 Director 2500-W AC Power Supply for the Cisco MDS 9509 Director Cisco MDS 9506 Power Supplies 11 Cisco MDS 9506 Power Supply 1900-W AC or DC Fan Modules Supervisor Modules Supervisor-2 Modules 12 Cisco MDS 9500 Series Supervisor-2 Module Port Interfaces Control and ManagementProcessor Memory Bytes LEDs on the Supervisor-2 Module 13 Supervisor-2 Module LEDs Mgmt Green Link is up 10/100/1000 Off No link Ethernet LinkLED Supervisor-1 Modules 14shows a Cisco MDS 9500 Series Supervisor-1 module Crossbar Switching Fabric LEDs on the Supervisor-1 Module 15 Supervisor-1 Module LEDs LEDs for the Cisco MDS 9500 Series Supervisor Modules Crossbar Modules 16 Crossbar Module LEDs LEDs for the Cisco MDS 9500 Crossbar Modules Cisco MDS 9000 Series Module Compatibility Module 9513 9509 9506 9222i 9216A 9216i Port Index Availability Module Physical Ports Port Indexes AllocatedSSM Example 1-1 Borrowing Port Indexes from Another Slot Port 4-Gbps Fibre Channel switching module Supervisor-1 Supervisor Module Port Index Requirements Ports Indexes Port 4-Gbps Fibre Channel switching module Supervisor-2Physical Port Slot No Modules in Cisco MDS 9509 Director Physical Port Slot No Modules in Cisco MDS 9513 Director Switching Modules Generation 2 modulesGeneration 1 modules Port 8-Gbps Fibre Channel Switching Module Port 8-Gbps Host-Optimized Fibre Channel Switching Module Port 4-Gbps Fibre Channel Switching Module Link LEDs Status LED Fibre Channel ports Link LEDs Port group Status LED Link LEDs Fibre Channel ports Port 10-Gbps Fibre Channel Switching Module Status LED Link LED X2 port interfaces LEDs on the Generation 2 Switching Modules Port 2-Gbps Fibre Channel Switching Module 25 Cisco MDS 9000 Family 32-Port 2-Gbps Switching Module Switching Module Features LEDs on the Generation 1 Switching Module Services Modules 18/4-Port Multiservice Module 27shows the MSM-18/4 module LEDs on the 18/4-Port Multiservice Module 15describes the LEDs for the 18/4-port Multiservice module 14/2-Port Multiprotocol Services Module LEDs on the MPS-14/2 Module 16describes the LEDs for the MPS-14/2 modules IP Storage Services Modules Status LED Link LEDs Gigabit Ethernet ports Asset tag LEDs on IP Storage Services Modules 17describes the LEDs for the IPS services modules Port Fibre Channel Advanced Services Module 31shows the Fibre Channel ASM LEDs on the Fibre Channel Advanced Services Modules 18describes the LEDs for the ASM Port Fibre Channel Storage Services Module 32shows the SSM LEDs on the Storage Services Modules 19describes the LEDs for the Storage Services Modules Caching Services Module 33shows the CSM Battery Disk drive LEDs on the Caching Services Module 20describes the LEDs for the CSM Supported Transceivers X2 Transceivers Fibre Channel SFP Transceivers Combination Fibre Channel/Gigabit Ethernet SFP TransceiversGigabit Ethernet SFP Transceivers Dwdm Fibre Channel SFP Transceivers Product Overview Supported Transceivers Installing the Cisco MDS 9500 Series Preinstallation Installation OptionsThis section provides the following topics Installation Guidelines Installing the Cisco MDS 9500 Series Preinstallation Unpacking and Inspecting the Switch Required Equipment Installing the Chassis in a Cabinet or Rack Installing the Cisco MDS 9513 Director in a Rack Quantity Part Description Positioning the Rack-Mount Support Brackets Positioning the Support Bars Securing the Rack-Mount Support Brackets Installing the Cisco MDS 9509 Director in a Rack Screws, 12-24 or Mounting rail Support bracket Cable guide M3 x 8-mm Phillips pan-head screws 12-24 x 3/4-inch Phillips binder-head screws10-32 x 3/4-inch Phillips binder-head screws Side rack-mount brackets Front of rack Installing the Cisco MDS 9509 Chassis in the Rack Crossbar Mounting rail Installing the Cisco MDS 9506 Director in a Rack 12-24 x 3/4-in. Phillips binder-head screws 10-32 x 3/4-in. Phillips binder-head screwsM4 x 6-mm Phillips pan-head screws System Grounding Proper Grounding Practices Environment Level Grounding Recommendations Preventing Electrostatic Discharge Damage Cisco MDS 9500 Series Hardware Installation Guide 133947 Establishing the System Ground Required Tools and Equipment Grounding the Chassis 144510 ESD plug ESD socket 12 ESD Ground Location on the Cisco MDS 9513 Chassis Rear 13 System Ground Location on the Cisco MDS 9509 Chassis 14 System Ground Location on the Cisco MDS 9506 Chassis Starting Up the Switch Connecting the Power SuppliesThis section provides the following information 15 Cable Retention on the Power Supply 16 2500-W AC Power Supply for the Cisco MDS 9509 Director Captive screws AC power connection PEM switch 18shows an AC PEM for a Cisco MDS 9506 Director 19 Power Supply for Cisco MDS 9506 Director 20shows the 2500-W DC power supply Statement 21 DC PEM for a Cisco MDS 9506 Director Powering Up the Switch and Verifying Component Installation Installing the Cisco MDS 9500 Series Starting Up the Switch This section provides the following information Removing Supervisor Modules Installing Supervisor Modules Slot guides EMI Gasket 22 Positioning a Module in the Chassis 23 Clearing the EMI Gasket 24 Closing the Ejector Levers Removing a Caching Services Module Removing Other Switching and Services Modules Cisco MDS 9500 Series Hardware Installation Guide Removing and Installing a Crossbar Module 25 Captive Screws and Ejector Levers on the Crossbar Module 26 Installing the Crossbar Module Maintaining a Caching Services Module Maintaining the Batteries on the Caching Services ModuleTighten the two captive screws on the module to 8 in-lb Removing and Installing a Power Supply or PEM Maintaining the Disk Drives on the Caching Services Module Removing an AC Power Supply from the Cisco MDS 9513 Director 28 Handling a Power Supply for the Cisco MDS 9513 Director Installing an AC Power Supply in the Cisco MDS 9513 Director 29 AC Power Supply for the Cisco MDS 9513 Director Removing an AC Power Supply from the Cisco MDS 9509 Director Installing an AC Power Supply in the Cisco MDS 9509 Director 31 4000-W AC Power Supply for the Cisco MDS 9509 Director 32 3000-W AC Power Supply for the Cisco MDS 9509 Director 33 2500-W AC Power Supply for the Cisco MDS 9509 Director Removing a DC Power Supply from the Cisco MDS 9509 Director DC power supply for the Cisco MDS 9509 Director is 2500 W Installing a DC Power Supply in the Cisco MDS 9509 Director OL-17467-02 Removing an AC PEM Removing a DC PEM 35 Connecting or Disconnecting the DC PEM Installing an AC PEM Installing a DC PEM 36 Handling a Power Supply for the Cisco MDS 9506 Director Removing and Installing Fan Modules Removing a Front Fan Module on the Cisco MDS 9513 Director This section includes the following topics Installing a Front Fan Module on the Cisco MDS 9513 Director Removing the Crossbar Module Fan Tray Installing the Crossbar Module Fan Tray 38 Removing a Crossbar Module Fan Tray Installing a Front Fan Module on the Cisco MDS 9509 Director Removing a Front Fan Module on the Cisco MDS 9509 Director Installing a Front Fan Module on the Cisco MDS 9506 Director Removing a Front Fan Module on the Cisco MDS 9506 Director Removing and Installing CompactFlash Cards Removing a CompactFlash Card Cisco MDS 9513 clock module Removing and Installing Clock ModulesInstalling a CompactFlash Card Disposable ESD wrist strap Removing a Clock Module from the Cisco MDS 9513 Director Repeat and to remove any additional clock modules Installing a Clock Module into the Cisco MDS 9513 Director 42 Clock Module for the Cisco MDS 9513 Director Removing a Clock Module from the Cisco MDS 9509 Director Cisco MDS 9509 clock moduleM3 x 6-mm Phillips pan-head screws OL-17467-02 Connectors Clock module Installing a Clock Module into the Cisco MDS 9509 Director Removing a Clock Module from the Cisco MDS 9506 DirectorCisco MDS 9506 clock module 120093 Connector Installing a Clock Module into the Cisco MDS 9506 Director Overview Usage Guidelines Generation 3 Module Fabric Module Software Release Migration Procedures for the MDS 9513 Director Before You Begin Upgrading the MDS 9513 Director CLI Configuration Guide Switch# out-of-service xbar Damage section on 188730 Figure A-2 Installing a Fabric Module Slot Switch# show module xbar Figure A-3 Strategy 2 Migration Process Flow Switch# show hardware fabric-mode Mod World-Wide-Names WWN 10.182 304 OL-17467-02 Cisco MDS 9500 Series Hardware Installation Guide Connecting the Cisco MDS 9500 Series Connecting to the Console Port Preparing for Network Connections 91701 Connecting to the COM1 Port 99272 Connecting to the Mgmt 10/100/1000 Ethernet Port Connecting to the Mgmt 10/100 Ethernet Port 99328 Connecting to a Fibre Channel Port Removing and Installing X2 Transceivers Figure B-5 Cisco MDS 9000 Family X2 Transceivers Installing an X2 Transceiver Removing an X2 Transceiver Removing and Installing SFP Transceivers Removing an SFP Transceiver 115237 Removing and Installing Cables into SFP Transceivers Installing an SFP TransceiverRemoving a Cable from an SFP Transceiver Installing a Cable into an SFP Transceiver Maintaining SFP Transceivers and Fiber-Optic Cables Cabinet and Rack Requirements General Requirements for Cabinets and Racks Cabinet and Rack Requirements for the Cisco MDS 9513 Chassis Requirements Specific to Perforated Cabinets Panduit Corporation Requirements Specific to Solid-Walled Cabinets Rittal Corporation Requirements Specific to Standard Open Racks Cisco MDS 9000 Family Telco and EIA Shelf Bracket Requirements Specific to Two-Post Telco Racks MDS Rack Type MDS 9216A Before Installing the Rack-Mount Support BracketsRack-Mounting Guidelines EIA 4-Post Before Installing the Shelf Brackets Required Equipment Installing the Shelf Bracket Kit into a Two-Post Telco Rack Installing the Shelf Bracket Kit into a Four-Post EIA Rack Figure C-2 Installing the Shelf Bracket Kit into an EIA Rack Installing the Switch on the Rack-Mount Support Brackets Installing the Switch on the Shelf Brackets Removing the Shelf Bracket Kit Optional Cisco MDS 9500 Shelf Bracket 20 x 3/4 in. Phillips pan-head screws with lock washers 10-32 x 1/3 in. Phillips pan-head screws with lock washersClip nuts Figure C-3 Installing the Shelf Bracket Kit into a Rack Installing the Switch on the Shelf Brackets Switch Specifications Description Specification Appendix D Technical Specifications Switch Specifications Table D-3 Module Specifications Physical Characteristics Weight of Modules Module Weight Power Specifications for the Cisco MDS 9513 Director Specifications for the Cisco MDS 9513 Power SuppliesAttribute Value Table D-8 Specifications for Cisco MDS 9513 Power Supplies Required Dissipation 90 VAC 120 VAC 180 VAC 240 VAC AC Power Consumption for the Cisco MDS 9513 DirectorPower Heat Input Current Module Type Release Watts BTU/hr Amps Power Specifications for the Cisco MDS 9509 Director Specifications for the Cisco MDS 9509 Power SuppliesModule Type / Product Number DC Power Supply NX-OS SAN-OS DS-X9308-SMIP 220 940 Port IPS module 160 683DS-X9304-SMIP SAN-OS Release Watts BTU/hr Amps Power HeatModule Type Required Dissipation 48 VDC 60 VDC 220 1000 Port IPS module 160 728 Power Specifications for the Cisco MDS 9506 Director AC Power Consumption for the Cisco MDS 9509 Director Specifications for the Cisco MDS 9506 Power Supplies VDC NX-OS SAN-OS VDC amps Cisco MDS 126 573 Chassis with fan module DS-C9506 200 910 DS-X9560-SMC 210 955 X2 Transceiver Specifications AC Power Consumption for the Cisco MDS 9506 Director Transceiver Module Product Number Description Type Power dBmCisco 10-Gbps Fibre Channel X2 Transceivers Average Transmit Average Receive Cisco 10-Gbps Ethernet X2 Transceivers Operating Storage SFP and SFP+ Transceiver Specifications Cisco 10-Gbps Ethernet Dwdm X2 Transceiver Cisco Fibre Channel SFP and SFP+ Transceivers Fiber Type Micon GBd Meter Average Transmit Average Receive Power dBmWavelength Core Size Baud Rate Cable Distance 125 Miles 10 km 250 500 Safety Information for the Cisco MDS 9000 Family DBm 0625 Miles 10 km 125 Power dBm DBmNanometer Fiber Type Micon GBd Meter 10.0 Micron 62 50 micron OM2 Cisco Fibre Channel and Gigabit Ethernet Transceivers Parameter Symbol Min Max UnitStorage temperature Case temperature Relative humidity DS-SFP-FCGE-LW Power dBm Fiber Loss Budget dBm 10.0 FC 17 GE FC 62.5 micron FC 50.0 micron GE 62.5 micron11.0 19 GE Cisco Cwdm SFP Transceivers Description Color All Cisco 2-Gbps 40C 85C Suppression Ratio Transmitter Optical Parameters Symbol Minimum Typical Maximum UnitsSmsr 1450 1620 Input Wavelength Transmitter All Cisco 4-Gbps 40C 85C Transceiver Module Product Number Description Cisco Gigabit Ethernet TransceiversCisco Dwdm SFP Transceivers DS-SFP-GE-T OL-17467-02 Cisco MDS 9500 Series Hardware Installation Guide Cable and Port Specifications Cables and Adapters Provided Console Port Pinouts Pin SignalConsole Port Console COM1 Port COM1 Port PinoutsDCD DB-9F/RJ45F RJ-45 Connecting the COM1 Port to a ModemMgmt 10/100/1000 Ethernet Port CTS DSR DCD TD+ RD+Not used Figure E-3 RJ-45 Interface Cable Connector Mgmt 10/100 Ethernet Port Supported Power Cords and Plugs Power Cords USA MDS 9509 2500W Power SupplyLength Description Feet Meters MDS 94973 United Kingdom BS89/13, BS 1363/A 13 a replaceable fuse Jumper Power Cord Supported Plugs for the 4000-W AC Power Supply Power Supply AC Power Cords Power Cord AC Power Cord Illustrations CAB-9K20A-NA CAB-9K16A-AUS CAB-9K16A-EU OL-17467-02 Site Planning and Maintenance Records Contacting Customer Service Finding the Chassis Serial Number Figure F-1 Serial Number Location on Cisco MDS 9513 Director Figure F-2 Serial Number Location on Cisco MDS 9509 Director Site Preparation Checklist Task No Planning Activity Verified By Time Date Task No Planning Activity Verified By Time Date Contact and Site Information Chassis and Module Information Slot Module Type Module Serial Number Supervisor Slot Module Type Module Serial Number Supervisor Port 8-Gbps Fibre Channel switching modules description BladeswitchProviding MDS 9509 Director Installing in a rack procedure Power supplies Removing from MDS 9506 Director procedure Mesh design Supervisor-2 modules Figure B-15 LEDs ASM table Clock modules Supervisor-2 modules table Installing in a rack procedure Power supply LEDs table Removing clock modules procedure CSM Power supplies MDS 9509 Director LEDs LEDs table MDS 9506 Director LEDs tableMDS 9509 Director LEDs table Cwdm Description Generation 1 modules InstallingASM CSM Dwdm IN-8 IN-9 CSM IN-11 Nebs IN-13 SSM IN-15 IN-16