Manuals / Cisco Systems / Computer Equipment / Network Card

Cisco Systems MDS 9500 Series manual Removing a Front Fan Module on the Cisco MDS 9509 Director

Models: MDS 9500 Series

1 288

Download 288 pages 59.22 Kb

Page 153

Chapter 2 Installing the Cisco MDS 9500 Series

Removing and Installing Fan Modules

Se n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a ck - d o c @ c i s c o . c o m .

Removing a Front Fan Module on the Cisco MDS 9509 Director

To remove a fan module from the Cisco MDS 9509 or 9506 switch, follow these steps:

Step 1 Loosen the two captive screws on the fan module (see Figure 2-39) by turning them counterclockwise; use a flat-blade or number 2 Phillips screwdriver, if required.

Step 2 Grasp the fan module with both hands and pull it outward; rock it gently, if necessary, to unseat the power connector from the backplane.

Step 3 Pull the fan module clear of the chassis.

Figure 2-39 Handling the Fan Module for the Cisco MDS 9509 Director

91685

Installing a Front Fan Module on the Cisco MDS 9509 Director

To install a front fan module on the Cisco MDS 9509 Director, follow these steps:

Step 1 Hold the fan module so that the Fan Status LED is at the top. (See Figure 2-39.)

Step 2 Place the fan module into the front chassis cavity so it rests on the chassis, lift the fan module up slightly to align the top and bottom chassis guides, then push the fan module into the chassis until it seats in the backplane and the captive screws make contact with the chassis.

		Cisco MDS 9500 Series Hardware Installation Guide
		Cisco MDS 9500 Series Hardware Installation Guide
	OL-17467-02			2-73
	OL-17467-02			2-73

Image 153

Cisco Systems MDS 9500 Series manual Removing a Front Fan Module on the Cisco MDS 9509 Director

Contents

Americas Headquarters Cisco MDS 9500 Series Hardware Installation GuidePage N T E N T S Port Index Availability Removing and Installing a Crossbar Module Installing an AC Power Supply in the Cisco MDS 9513 Director Cabinet and Rack Installation C-1 Chassis Console Port E-2 COM1 Port E-3 Feature Description Release Where Documented Fips SFP+Switching Module offers 24 autosensing 1 Switching Module offers 48 autosensing 1Switching Module can be used in any of the Cisco Cisco MDS 9216i and 9216A SwitchesChannel Services Module SSM 3000W Power Added 3000W power supply forInstallation Modules Specific Port IP Provided Fcip services and iSCSI 34aCwdm SFP SFPXiv Audience OrganizationChapter Title Description Conventions Provides a site-planning checklist and sample maintenanceAppendix E Appendix FXvii Hardware Installation Regulatory Compliance and Safety InformationRelated Documentation Release NotesTroubleshooting and Reference Command-Line InterfaceInstallation and Configuration Note Cisco Fabric ManagerPreface Product Overview Chassis Cisco MDS 9513 Director Cisco MDS 9513 Chassis Front Panel View Rear Panel 9513 Chassis Cisco MDS 9509 Director Cisco MDS 9506 Chassis Cisco MDS 9506 DirectorBackplane and Clock Modules Lower LEDs Upper LEDsStatus Description Power Supplies Cisco MDS Fibre Channel Switch for IBM Blade CenterPower supply switch Power Supply LEDs AC power connection Cisco MDS 9513 Power SuppliesOutput Fail FAN OK4000-W AC Power Supply for the Cisco MDS 9509 Director Cisco MDS 9509 Power Supplies3000-W AC Power Supply for the Cisco MDS 9509 Director 2500-W AC Power Supply for the Cisco MDS 9509 Director 11 Cisco MDS 9506 Power Supply 1900-W AC or DC Cisco MDS 9506 Power SuppliesSupervisor Modules Fan Modules12 Cisco MDS 9500 Series Supervisor-2 Module Supervisor-2 ModulesProcessor Control and ManagementPort Interfaces Memory Bytes13 Supervisor-2 Module LEDs LEDs on the Supervisor-2 ModuleMgmt Green Link is up 10/100/1000 Off No link Ethernet LinkLED 14shows a Cisco MDS 9500 Series Supervisor-1 module Supervisor-1 ModulesCrossbar Switching Fabric 15 Supervisor-1 Module LEDs LEDs on the Supervisor-1 ModuleLEDs for the Cisco MDS 9500 Series Supervisor Modules 16 Crossbar Module LEDs Crossbar ModulesLEDs for the Cisco MDS 9500 Crossbar Modules Module 9513 9509 9506 9222i 9216A 9216i Cisco MDS 9000 Series Module CompatibilityPort Index Availability Module Physical Ports Port Indexes AllocatedSSM Example 1-1 Borrowing Port Indexes from Another Slot Supervisor Module Port Index Requirements Port 4-Gbps Fibre Channel switching module Supervisor-1Physical Port Slot No Modules in Cisco MDS 9509 Director Port 4-Gbps Fibre Channel switching module Supervisor-2Ports Indexes Physical Port Slot No Modules in Cisco MDS 9513 DirectorSwitching Modules Generation 2 modulesGeneration 1 modules Port 8-Gbps Host-Optimized Fibre Channel Switching Module Port 8-Gbps Fibre Channel Switching ModuleLink LEDs Port 4-Gbps Fibre Channel Switching ModuleStatus LED Link LEDs Fibre Channel ports Status LED Fibre Channel ports Link LEDs Port groupStatus LED Link LED X2 port interfaces Port 10-Gbps Fibre Channel Switching ModulePort 2-Gbps Fibre Channel Switching Module LEDs on the Generation 2 Switching Modules25 Cisco MDS 9000 Family 32-Port 2-Gbps Switching Module Switching Module Features LEDs on the Generation 1 Switching Module 18/4-Port Multiservice Module Services Modules27shows the MSM-18/4 module 15describes the LEDs for the 18/4-port Multiservice module LEDs on the 18/4-Port Multiservice Module14/2-Port Multiprotocol Services Module 16describes the LEDs for the MPS-14/2 modules LEDs on the MPS-14/2 ModuleStatus LED Link LEDs Gigabit Ethernet ports Asset tag IP Storage Services Modules17describes the LEDs for the IPS services modules LEDs on IP Storage Services Modules31shows the Fibre Channel ASM Port Fibre Channel Advanced Services Module18describes the LEDs for the ASM LEDs on the Fibre Channel Advanced Services Modules32shows the SSM Port Fibre Channel Storage Services Module19describes the LEDs for the Storage Services Modules LEDs on the Storage Services Modules33shows the CSM Caching Services ModuleDisk drive Battery20describes the LEDs for the CSM LEDs on the Caching Services ModuleX2 Transceivers Supported TransceiversFibre Channel SFP Transceivers Combination Fibre Channel/Gigabit Ethernet SFP TransceiversGigabit Ethernet SFP Transceivers Dwdm Fibre Channel SFP Transceivers Product Overview Supported Transceivers Installing the Cisco MDS 9500 Series Preinstallation Installation OptionsThis section provides the following topics Installation Guidelines Installing the Cisco MDS 9500 Series Preinstallation Required Equipment Unpacking and Inspecting the SwitchInstalling the Chassis in a Cabinet or Rack Quantity Part Description Installing the Cisco MDS 9513 Director in a RackPositioning the Rack-Mount Support Brackets Positioning the Support Bars Securing the Rack-Mount Support Brackets Screws, 12-24 or Mounting rail Support bracket Cable guide Installing the Cisco MDS 9509 Director in a Rack10-32 x 3/4-inch Phillips binder-head screws 12-24 x 3/4-inch Phillips binder-head screwsM3 x 8-mm Phillips pan-head screws Side rack-mount bracketsFront of rack Crossbar Mounting rail Installing the Cisco MDS 9509 Chassis in the RackInstalling the Cisco MDS 9506 Director in a Rack 12-24 x 3/4-in. Phillips binder-head screws 10-32 x 3/4-in. Phillips binder-head screwsM4 x 6-mm Phillips pan-head screws Proper Grounding Practices System GroundingEnvironment Level Grounding Recommendations Preventing Electrostatic Discharge Damage Cisco MDS 9500 Series Hardware Installation Guide 133947 Required Tools and Equipment Establishing the System GroundGrounding the Chassis 144510 12 ESD Ground Location on the Cisco MDS 9513 Chassis Rear ESD plug ESD socket13 System Ground Location on the Cisco MDS 9509 Chassis 14 System Ground Location on the Cisco MDS 9506 Chassis Starting Up the Switch Connecting the Power SuppliesThis section provides the following information 15 Cable Retention on the Power Supply 16 2500-W AC Power Supply for the Cisco MDS 9509 Director 18shows an AC PEM for a Cisco MDS 9506 Director Captive screws AC power connection PEM switch19 Power Supply for Cisco MDS 9506 Director 20shows the 2500-W DC power supply Statement 21 DC PEM for a Cisco MDS 9506 Director Powering Up the Switch and Verifying Component Installation Installing the Cisco MDS 9500 Series Starting Up the Switch This section provides the following information Removing Supervisor Modules Installing Supervisor Modules 22 Positioning a Module in the Chassis Slot guides EMI Gasket23 Clearing the EMI Gasket 24 Closing the Ejector Levers Removing a Caching Services Module Removing Other Switching and Services Modules Cisco MDS 9500 Series Hardware Installation Guide Removing and Installing a Crossbar Module 25 Captive Screws and Ejector Levers on the Crossbar Module 26 Installing the Crossbar Module Maintaining a Caching Services Module Maintaining the Batteries on the Caching Services ModuleTighten the two captive screws on the module to 8 in-lb Maintaining the Disk Drives on the Caching Services Module Removing and Installing a Power Supply or PEMRemoving an AC Power Supply from the Cisco MDS 9513 Director 28 Handling a Power Supply for the Cisco MDS 9513 Director Installing an AC Power Supply in the Cisco MDS 9513 Director 29 AC Power Supply for the Cisco MDS 9513 Director Removing an AC Power Supply from the Cisco MDS 9509 Director Installing an AC Power Supply in the Cisco MDS 9509 Director 31 4000-W AC Power Supply for the Cisco MDS 9509 Director 32 3000-W AC Power Supply for the Cisco MDS 9509 Director 33 2500-W AC Power Supply for the Cisco MDS 9509 Director DC power supply for the Cisco MDS 9509 Director is 2500 W Removing a DC Power Supply from the Cisco MDS 9509 DirectorInstalling a DC Power Supply in the Cisco MDS 9509 Director OL-17467-02 Removing a DC PEM Removing an AC PEM35 Connecting or Disconnecting the DC PEM Installing a DC PEM Installing an AC PEM36 Handling a Power Supply for the Cisco MDS 9506 Director Removing and Installing Fan Modules This section includes the following topics Removing a Front Fan Module on the Cisco MDS 9513 DirectorInstalling a Front Fan Module on the Cisco MDS 9513 Director Removing the Crossbar Module Fan Tray 38 Removing a Crossbar Module Fan Tray Installing the Crossbar Module Fan TrayRemoving a Front Fan Module on the Cisco MDS 9509 Director Installing a Front Fan Module on the Cisco MDS 9509 DirectorRemoving a Front Fan Module on the Cisco MDS 9506 Director Installing a Front Fan Module on the Cisco MDS 9506 DirectorRemoving a CompactFlash Card Removing and Installing CompactFlash CardsInstalling a CompactFlash Card Removing and Installing Clock ModulesCisco MDS 9513 clock module Disposable ESD wrist strapRemoving a Clock Module from the Cisco MDS 9513 Director Repeat and to remove any additional clock modules 42 Clock Module for the Cisco MDS 9513 Director Installing a Clock Module into the Cisco MDS 9513 DirectorRemoving a Clock Module from the Cisco MDS 9509 Director Cisco MDS 9509 clock moduleM3 x 6-mm Phillips pan-head screws OL-17467-02 Connectors Clock module Installing a Clock Module into the Cisco MDS 9509 Director Removing a Clock Module from the Cisco MDS 9506 DirectorCisco MDS 9506 clock module 120093 Connector Installing a Clock Module into the Cisco MDS 9506 Director Overview Generation 3 Module Fabric Module Software Release Usage GuidelinesBefore You Begin Upgrading the MDS 9513 Director Migration Procedures for the MDS 9513 DirectorCLI Configuration Guide Switch# out-of-service xbar Damage section on 188730 Slot Figure A-2 Installing a Fabric ModuleSwitch# show module xbar Figure A-3 Strategy 2 Migration Process Flow Switch# show hardware fabric-mode Mod World-Wide-Names WWN 10.182 304 OL-17467-02 Cisco MDS 9500 Series Hardware Installation Guide Connecting the Cisco MDS 9500 Series Preparing for Network Connections Connecting to the Console Port91701 Connecting to the COM1 Port 99272 Connecting to the Mgmt 10/100/1000 Ethernet Port Connecting to the Mgmt 10/100 Ethernet Port 99328 Removing and Installing X2 Transceivers Connecting to a Fibre Channel PortFigure B-5 Cisco MDS 9000 Family X2 Transceivers Removing an X2 Transceiver Installing an X2 TransceiverRemoving an SFP Transceiver Removing and Installing SFP Transceivers115237 Removing and Installing Cables into SFP Transceivers Installing an SFP TransceiverRemoving a Cable from an SFP Transceiver Installing a Cable into an SFP Transceiver Maintaining SFP Transceivers and Fiber-Optic Cables General Requirements for Cabinets and Racks Cabinet and Rack RequirementsCabinet and Rack Requirements for the Cisco MDS 9513 Chassis Panduit Corporation Requirements Specific to Perforated CabinetsRittal Corporation Requirements Specific to Solid-Walled CabinetsRequirements Specific to Standard Open Racks Requirements Specific to Two-Post Telco Racks Cisco MDS 9000 Family Telco and EIA Shelf BracketRack-Mounting Guidelines Before Installing the Rack-Mount Support BracketsMDS Rack Type MDS 9216A EIA 4-PostRequired Equipment Before Installing the Shelf BracketsInstalling the Shelf Bracket Kit into a Two-Post Telco Rack Figure C-2 Installing the Shelf Bracket Kit into an EIA Rack Installing the Shelf Bracket Kit into a Four-Post EIA RackInstalling the Switch on the Rack-Mount Support Brackets Removing the Shelf Bracket Kit Optional Installing the Switch on the Shelf BracketsCisco MDS 9500 Shelf Bracket 20 x 3/4 in. Phillips pan-head screws with lock washers 10-32 x 1/3 in. Phillips pan-head screws with lock washersClip nuts Figure C-3 Installing the Shelf Bracket Kit into a Rack Installing the Switch on the Shelf Brackets Description Specification Switch SpecificationsAppendix D Technical Specifications Switch Specifications Table D-3 Physical Characteristics Module SpecificationsModule Weight Weight of ModulesPower Specifications for the Cisco MDS 9513 Director Specifications for the Cisco MDS 9513 Power SuppliesAttribute Value Table D-8 Specifications for Cisco MDS 9513 Power Supplies Power Heat Input Current Module Type AC Power Consumption for the Cisco MDS 9513 DirectorRequired Dissipation 90 VAC 120 VAC 180 VAC 240 VAC Release Watts BTU/hr AmpsPower Specifications for the Cisco MDS 9509 Director Specifications for the Cisco MDS 9509 Power SuppliesModule Type / Product Number DC Power Supply NX-OS SAN-OS DS-X9308-SMIP 220 940 Port IPS module 160 683DS-X9304-SMIP Module Type Required Dissipation 48 VDC 60 VDC Power HeatSAN-OS Release Watts BTU/hr Amps 220 1000 Port IPS module 160 728AC Power Consumption for the Cisco MDS 9509 Director Power Specifications for the Cisco MDS 9506 DirectorVDC Specifications for the Cisco MDS 9506 Power SuppliesNX-OS SAN-OS Cisco MDS 126 573 Chassis with fan module DS-C9506 VDC amps200 910 DS-X9560-SMC 210 955 AC Power Consumption for the Cisco MDS 9506 Director X2 Transceiver SpecificationsCisco 10-Gbps Fibre Channel X2 Transceivers Power dBmTransceiver Module Product Number Description Type Average Transmit Average ReceiveOperating Storage Cisco 10-Gbps Ethernet X2 TransceiversCisco 10-Gbps Ethernet Dwdm X2 Transceiver SFP and SFP+ Transceiver SpecificationsCisco Fibre Channel SFP and SFP+ Transceivers Wavelength Core Size Baud Rate Cable Distance Average Transmit Average Receive Power dBmFiber Type Micon GBd Meter 125 Miles 10 km 250 500Safety Information for the Cisco MDS 9000 Family DBm Nanometer Fiber Type Micon GBd Meter Power dBm DBm0625 Miles 10 km 125 10.0 Micron 62 50 micron OM2Storage temperature Case temperature Relative humidity Parameter Symbol Min Max UnitCisco Fibre Channel and Gigabit Ethernet Transceivers DS-SFP-FCGE-LWPower dBm Fiber Loss Budget dBm 10.0 FC 17 GE FC 62.5 micron FC 50.0 micron GE 62.5 micron11.0 19 GE Description Color Cisco Cwdm SFP TransceiversAll Cisco 2-Gbps 40C 85C Smsr Parameters Symbol Minimum Typical Maximum UnitsSuppression Ratio Transmitter Optical 1450 1620 Input Wavelength TransmitterAll Cisco 4-Gbps 40C 85C Cisco Dwdm SFP Transceivers Cisco Gigabit Ethernet TransceiversTransceiver Module Product Number Description DS-SFP-GE-TOL-17467-02 Cisco MDS 9500 Series Hardware Installation Guide Cables and Adapters Provided Cable and Port SpecificationsConsole Port Pin SignalConsole Port Pinouts ConsoleCOM1 Port COM1 Port PinoutsDCD Mgmt 10/100/1000 Ethernet Port Connecting the COM1 Port to a ModemDB-9F/RJ45F RJ-45 CTS DSR DCDTD+ RD+Not used Mgmt 10/100 Ethernet Port Figure E-3 RJ-45 Interface Cable ConnectorPower Cords Supported Power Cords and PlugsLength Description Feet Meters MDS 9509 2500W Power SupplyUSA MDS94973 United Kingdom BS89/13, BS 1363/A 13 a replaceable fuse Supported Plugs for the 4000-W AC Power Supply Jumper Power CordPower Cord Power Supply AC Power CordsCAB-9K20A-NA AC Power Cord IllustrationsCAB-9K16A-AUS CAB-9K16A-EU OL-17467-02 Contacting Customer Service Site Planning and Maintenance RecordsFigure F-1 Serial Number Location on Cisco MDS 9513 Director Finding the Chassis Serial NumberFigure F-2 Serial Number Location on Cisco MDS 9509 Director Task No Planning Activity Verified By Time Date Site Preparation ChecklistTask No Planning Activity Verified By Time Date Contact and Site Information Slot Module Type Module Serial Number Supervisor Chassis and Module InformationSlot Module Type Module Serial Number Supervisor Port 8-Gbps Fibre Channel switching modules description BladeswitchProviding MDS 9509 Director Removing from MDS 9506 Director procedure Installing in a rack procedure Power suppliesMesh design Supervisor-2 modules Supervisor-2 modules table Figure B-15 LEDs ASM table Clock modulesRemoving clock modules procedure Installing in a rack procedure Power supply LEDs tableCSM Power supplies MDS 9509 Director LEDs LEDs table MDS 9506 Director LEDs tableMDS 9509 Director LEDs table ASM CSM Description Generation 1 modules InstallingCwdm DwdmIN-8 IN-9 CSM IN-11 Nebs IN-13 SSM IN-15 IN-16