Lexmark IBM 9077 manual Grit

/root netstat -in
Name	Mtu	Network	Address	Ipkts Ierrs		Opkts Oerrs		Coll
de0	1500	<link1>	00:c0:80:96:38:68	10290	0	42228	0	182
de0	1500	<Bridge>	00:c0:80:96:38:68	10290	0	42228	0	182
de0	1500	192.168.4	192.168.4.4	10290	0	42228	0	182
rmb0	616	<link2>	00:00:00:00:00:00	170556	74	41439	0	0
rmb0	616	<GRIT>	0:0x40:0	170556	74	41439	0	0
lo0	1536	<link3>		8387	0	8387	0	0
lo0	1536	127	127.0.0.1	8387	0	8387	0	0
lo0	1536	<GRIT>	0:0x48:0	8387	0	8387	0	0
gf000	4352	<link10>	00:c0:80:89:2d:f2	19	0	20	0	0
gf000	4352	10.2.1/24	10.2.1.15	19	0	20	0	0
gf001	4352	<link20>	00:c0:80:89:2d:f3	12	0	12	0	0
gf001	4352	10.3.1/24	10.3.1.16	12	0	12	0	0
gf002	4352	<link11>	00:c0:80:89:2d:f4	13	0	13	0	0
gf002	4352	10.4.1/24	10.4.1.17	13	0	13	0	0
gf003	4352	<link12>	00:c0:80:89:2d:f5	13	0	19	0	0
gf003	4352	10.5.1/24	10.5.1.18	13	0	19	0	0

7.On the CWS of SP21, check if the SP Switch Router Adapter card is configured. To perform this check, look if the SP Switch Router Adapter card shows up green in perspectives or enter SDRGetObjects switch_responds. Use Eunfence if needed.

8.Issue some ping commands to check the connection:

On the chosen SP21 nodes, ping all four FDDI interfaces of the nodes in SP2, for example:

root@sp21n01:/ ping 10.2.1.12

PING 10.2.1.12: (10.2.1.12): 56 data bytes

64 bytes from 10.2.1.12: icmp_seq=0 ttl=254 time=10 ms

64 bytes from 10.2.1.12: icmp_seq=1 ttl=254 time=1 ms ^C

----10.2.1.12 PING Statistics----

2 packets transmitted, 2 packets received, 0% packet loss round-trip min/avg/max = 1/5/10 ms

On node 9-12 in SP2, ping the SP Switch interfaces of the chosen nodes in SP21, for example:

root@sp2n12:/ ping 192.168.14.1

PING 192.168.14.1: (192.168.14.1): 56 data bytes

64 bytes from 192.168.14.1: icmp_seq=0 ttl=254 time=1 ms

64 bytes from 192.168.14.1: icmp_seq=1 ttl=254 time=1 ms ^C

----192.168.14.1 PING Statistics----

2 packets transmitted, 2 packets received, 0% packet loss round-trip min/avg/max = 1/1/1 ms

178IBM 9077 SP Switch Router: Get Connected to the SP Switch