Turning ON/OFF the Power Switch | Omega RD100B specs

2.6 Turning ON/OFF the Power Switch

CAUTION

Check the following points before turning ON the power switch.

•The power cord/wires are connected correctly to the recorder.

•The recorder is connected to the correct power supply (see section 2.5).

The power switch is located inside the door at the lower right.

The power switch is a push button. Press once to turn it ON and press again to turn it

OFF.

When the power switch is turned ON, a self-diagnosis program runs for a few seconds, and the recorder is ready for operation.

Note

•If the input wires are connected in parallel with other devices, do not turn ON/OFF the power switch of the recorder or another device during operation. This can have adverse effects on the measured values.

•If nothing is displayed when the power switch is turned ON, turn OFF the power switch and check the points listed above one more time. After checking the points, turn ON the power switch again. If the unit still does not work, it is probably malfunctioning. Contact OMEGA for repairs.

•If an error message is displayed on the screen, take measures according to the description in chapter 10, “Troubleshooting.”

•Turn ON the power switch, let the recorder warm up for at least 30 minutes, and then start the measurements.

Checking the Date/Time

The date/time is shown on the display when the DISP key is pressed several times. To correct the date/time, see the reference indicated below.

<Related Topics>

Setting the date/time: See section 5.5

2-14

Image 58

Omega RD100B manual Turning ON/OFF the Power Switch, Checking the Date/Time

Contents

User’s Guide For immediate technical or application assistance Revisions ForewordTrademarks Electronic Manuals Provided on the Accompanying CD-ROM Software Sold Separately Recorder’s Version and Functions Described in This ManualRD100B Versions and Functions Version Suffix Code Added or Modified Functions Reference About This Manual Safety PrecautionsSafety Standards and EMC Standards Iii Handling Precautions of the Software Exemption from Responsibility Checking the Contents of the Package Optional Accessories Sold Separately Standard AccessoriesChecking the Contents of the Package Dot Model Removing the Packing MaterialsPen Model Vii How to Use This Manual Viii Conventions Used in This Manual Contents Setup Operations for Convenient Functions Setting Mode Contents Maintenance Xii Overview of the Recorder Measuring Input Section Input Section Scaling Measuring Input Section Delta ComputationSquare Root Computation Reference Junction Compensation of Thermocouple Input Burnout Detection of ThermocouplesMeasuring Input Section Bias Filter and Moving Average Noise Elimination from Input SignalsMeasuring Input Section Filter Pen Model Integration Time of the A/D Converter Model Integration Time of the A/D Converter Alarms Alarm Types Delay High Limit Alarm Example T is the specified delay Alarms Delay High Limit Alarm TDelay Low Limit Alarm t Alarm Hysteresis Alarm Output Relay /A1, /A2, and /A3 Options Alarm IndicationAlarm Recording Non-Hold/Hold Operation of the Alarm Indication Alarm Alarms Reflash AlarmChannel Approx ms Approx ms Functional Alarms AND/OR Operation of Alarm Output RelaysEnergized/De-energized Operation of Alarm Output Relays Description Alarm ACK Operation Alarms Non-Hold/Hold Operation of Alarm Output Relays Recording Recording Method Pen Model Chart SpeedTrend Recording Recording Method Dot Model Compressed Expanded Recording Partial Expanded RecordingPen Offset Compensation Pen Model Same time Printout Printout Example on the Pen Model Recording Printout Example on the Dot Model Functional Description Channel Printout Dot Model Only Periodic Printout Recording Alarm PrintoutPrintout Contents for details, see appendix Interval Manual Printout New Chart Speed PrintoutRecording Turning ON/OFF the Periodic Printout Message Printout Recording Setting Printout Printout Example of List on the Pen Model Printout Example of List on the Dot Model Displayed Information DisplayDisplay Types Channel Digital + 1 Bar Graph Display Alarm Status DisplayDate/Time and Chart Speed Flag Display Channels Dedicated to Computations Computation Function /M1 OptionComputation Function Types of Computations Trend Recording Handing of the Unit in ComputationsRecording Computation Channels Assignment of Computation Channels to the Pens Pen Model Starting/Stopping Computation AlarmsDisplay Printout Fail Output FAIL/Chart End Detection and Output Function /F1 OptionChart End Output Fail Relay Output Remote Control Function /R1 Option Remote Signal Edge, Trigger, and Level Remote Control Function /R1 Option Computation Start/StopComputation Reset Rising/Falling edge Trigger Level Ms or more Key Lock Temperature UnitOther Functions Language Handling Precautions Handling PrecautionsBefore Using the Recorder Installation Installation Location Front Contact With each other Installation ProcedureInstallation Flat blade External Dimensions of the Recorder Panel Cutout General Precautions to Be Taken While Wiring Input Signal WiringPrecautions to Be Taken While Wiring Screw input terminal Arrangement of the Measuring Input TerminalsMeasuring input terminal block Clamped input terminal H2 option Before Using Input Signal Wiring Dot ModelRecorder Input Signal Wiring Measuring Input WiringDC current input +/A Shunt resistor Crimp-on lug with insulation sleeves for 4 mm screws Optional Terminal WiringArrangement of the Optional Terminals Optional terminal block Optional Terminal Wiring Remote Control Input Terminals Relay Contact Input/Transistor Input Specifications Wiring ProcedureRelay Contact Output Specifications Relay contact output Voltage-free contact Open collector Precautions to Be Taken While Wiring the Power Supply Power Supply WiringPower Supply Specifications Power Supply Wiring Turning ON/OFF the Power Switch Checking the Date/Time Names of Parts and Run Operations Names of PartsFront Names of Parts Seven keys are available Display and Key PanelStatus display During normal operation CH UP key Rear Panel Names Parts Run Operations Loading the Chart Paper Installing or Replacing the Chart PaperStopper Chart holder Installing or Replacing the Chart PaperFold chart paper Sprocket teeth Side with Feeding the Chart Paper Replacing Felt Pens Installing/Replacing Felt Pens or Plotter Pen Pen ModelDisplay and key panel Replacing the Plotter Pen Installing/Replacing the Ribbon Cassette Dot Model Holder tab Cassette holder Installing/Replacing the Ribbon Cassette Dot ModelHole for the ribbon Feed shaft Ribbon feeding knob Starting the Recording Recorded chart paper can be pulled out Front cover tabStarting/Stopping the Recording Stopping the Recording Channel Auto Switching Switching the Display ScreenSwitching the Display Screen Switching the Displayed Channel Using Keys Starting the Manual Printout Printing Measured Values Manual PrintoutAborting the Manual Printout Aborting the Setup Printout Printing the Recorder SettingsStarting the Setup Printout Starting the List Printout Clearing the Alarm Printout Buffer Buf.clear=Alarm Printing a Message Displays the preset messagePrinting Messages Clearing the Message Printout Buffer Resetting the Report Data of the Periodic Printout Resetting the Report Data Alarm Output Relay Operation Releasing the Alarm Output Alarm ACK OperationReleasing the Alarm Output Alarm Alarm output relay Blinking Alarm indication Activating the Key Lock Activating/Releasing the Key LockReleasing the Key Lock Run Modes Exiting from Setting Mode Returning to Operation Mode Entering Setting ModeEntering Basic Setting Mode Exiting from Basic Setting Mode Returning to Operation Mode Entering Values Changing the SettingsUsing the ESC Key Key Operations Deleting a Character Entering CharactersInserting Characters Copying & Pasting a Character String Menu Structure, Settings, and List of Default Values Operation Menus Using the Func Key Operation Mode Exchange Dot Model Menu Structure of Setting Mode Menu Structure, Settings, and List of Default Values Menu Structure of Basic Setting Mode POC Setup Items in Setting Mode and Their Default Values Setup Items in Basic Setting Mode and Their Default Values RJC RJC Setting initialization Remote control function /R1 option NORMAL/MODBUS Normal Function Setup Guide Description Reference Section Alarm functions Description Reference Section Function Setup GuideRecording functions Description Reference Section Or tag Channel numberRecording color Display functions Description Reference Section Other functions Description Reference Section Timer number Computed value Frequently Used Setup Operations Setting Mode Setting the Input RangeTC, RTD, and DC Voltage N1 Option Setting the Input rangeSelectable Range of Input Range, Span Left, and Span Right Input Type Linear Scaling Span Left and Span Right Delta ComputationFirst channel Last channel ON/OFF Input Range Type Selectable Span Values Low-cut 5V InputScale Left and Scale Right Select the right scale value Low-cut and Low-cut Point Square Root ComputationTo 5.0% of the recording span, 0.1 steps Set the channel range Select Skip New setting takes effect Skip Unused Channels Setting the Alarm Symbol Name Setting the AlarmAlarm Type Channel Range Difference High Limit Alarm/Difference Low Limit Alarm Relay No Setting the Unit on Scaled Channels Chart speed on the pen model unit mm/h Changing the Chart SpeedMode Date/Time New setting takes effect Setting the Date/TimeRecorders with Version 1.02 or Earlier Functions Setting Mode Setting the Trend Recording Interval Dot ModelSetup Operations for Convenient Functions Setting Mode When set to Auto Setting the Filter Pen Model Filter Time Constant New setting takes effect Setting the Moving Average Dot ModelNumber of Samples of Moving Average Setting Recording Zones for Each Channel Zone Recording Zone Setting the Partial Expanded Recording Expand Trend Recording Dot Model Setting Tags on Channels Characters That Can Be Used for Tags Setting the Message String Characters That Can Be Used for Messages See section Setting the Alarm Delay Duration Duration New setting takes effect Display Brightness Setting the Brightness of the Display and Internal LightInternal Light Brightness Applying a Bias on the Measuring Input Signal When bias is On Setup Operations For Convenient Functions Setting Mode Start month, Strt day, and Start time End month, End day, and End time DST Changing the Auxiliary Alarm Function Changing the Settings Changing the Auxiliary Alarm Function Diagnosis Act Changing the Auxiliary Alarm Function ReflashIndicator Behavior Changing the Integration Time of the A/D Converter Integrate Setting the Burnout Detection Function of Thermocouples Burnout Setting the RJC Function on Channels Set to TC Input Setting the RJC Function on Channels Set to TC Input Volt Changing the Channel Recording Color Dot Model Color POC Pen Offset Compensation Turning Printouts ON/OFF Pen model Channel Dot Model AlarmCH/Tag Pen Color Printout Periodic Printout Interval Changing/Adding Functions Basic Setting Mode Types of Report Data to Be Printed Ref. Time SUM scale Functions Basic Setting Mode Setting the Bar Graph Display ModeSetup Graph Setting the Key Lock Function Setting the Key Lock Function Password Operation of Keys to Be Key-Locked Enabling the Moving Average Function Dot Model MovingAVE Enabling the Filter Function Pen Model Filter Enabling the Partial Expanded Recording Function Partial Changing the Display/Recording Language Lang Language Procedure Sqrt low-cut Alarm delay5V low-cut Changing the Time Printout Format RCD On Changing the Time Printout FormatSpeed Basic=Initialize screen Initializing the SettingsESC/? Changing the Settings Remote No Function to Be Assigned Changing the Printout/Display Format of the Date Setting Format ExampleDate Format Changing the Temperature Unit Temp Temperature Setup Operations for Changing Displayed Contents Setup Operations for Changing the Displayed ContentsDisplaying the Data Display Setup Screen Key Operations for Changing the Displayed Information End Data Display Setup MenuKey Operations for Changing the Displayed Information End Flag display Channel Digital Display Changing the Displayed ContentsChanging the Displayed Information Assigning Other Display Types See the menu on the previous Starting the Computation Starting/Stopping/Resetting the ComputationOperations Related to the Computation Function /M1 Option Stopping the Computation Setting the Computing Equation Inserting a Character Description Character Key Order of Precedence in Computations Computing EquationType Operator Four Arithmetic Operation Power and Other ComputationsEquation Examples Relational Computation Logical Computation XOR Equation Example 01-02OR03.GT.04 Equation Example Tlog ComputationExamples of Equations That Are Not Allowed Setting the Unit Characters That Can Be Used for Units Setting the Constants Used in Equations Constant Select On to set the alarm. When set Alarm Value Specifying the Timer Used in Statistical Calculations Tlog Timer operation Specifying the Timer Used in Statistical Calculations TlogTimer No Timer # Periodic Set the leftmost value of the recording New setting takes effect Related Topics Dot model Set= Math Math= Aux Aux= Tag Duration Basic=Math Math=TimerTLOG Timer No.=1 Mode=Absolute Timer Type TimersNumber of Timers Absolute Time Mode Timer timeout Reset Reset Reset Reset On Reset Off Example TLOG.SUM computation Select the channel Changing the Channel Assignments of Recording Pens Pen Model Output pen Operations Function /M1 Option Setting the periodic printout interval Section Select the display mode of the bar Select the computation error procedure Over ErrorChannel Limit Value Troubleshooting List of Error MessagesSetting Errors Troubleshooting 10-1 List of Error Messages Operation ErrorsCommunication Errors When the timer expired System Errors Troubleshooting 10-3 Troubleshooting Flow Charts 10-4 Troubleshooting Flow Charts 10-5 10-6 Remaining amount of chart paper MaintenanceMaintenance 11-1 Periodic Inspection Pen Model Cleaning the RecorderCleaning Procedure Dot Model Flexible printed circuit board LED assembly Connector Replacement ProcedureMaintenance 11-3 Replacing the Internal Light LED Calibrating the Recorder Calibration ProcedureRequired Instruments Maintenance 11-5 Temperature Measurement When Using a ThermocoupleRJC of TC input Basic=PAdj screen Adjusting the Pen Position Pen Model11-6 Adjusting Zero and Full Adjusting the Dot Printing Position Dot ModelAdjusting the Hysteresis Maintenance 11-7 Adjusting the Dot Printing Position Dot Model 11-8 Maintenance 11-9 Recommended Replacement Periods for Worn PartsPart Name Quantity Period Used Replacement Part Name Quantity Period Used Recommended Replacement Periods for Worn Parts Dot Model11-10 Number of Inputs and Scan Interval on the Dot Model Input SpecificationsNumber of Inputs and Scan Interval on the Pen Model Input Type 12-2 Input SpecificationsInput Computation Standard Function Input Type Operating Conditions Alarm Function Specifications Specifications 12-3 Trend Recording Pen Model Recording Function SpecificationsChart Paper Trend Recording Dot Model Specifications 12-5 Recording Function SpecificationsPrintouts Pen Model Printout Dot Model 12-6 Display Function Specifications Display and Displayed Contents 12-8 Display Function SpecificationsItemSpecifications Status Display Description Specifications 12-9 Symbol Description 12-10 Channel digital display Measurement channel Tag display Specifications 12-11Name Display Example DI/DO status display Status display Digital display is the same as 12-12 Specifications 12-13 Specifications of Optional FunctionsAlarm Output Relay /A1, /A2, and /A3 RS-422A/485 Communication Interface /C3 Non-Glare Door Glass /H3 FAIL/Chart End Detection and Output /F1Clamped Input Terminal /H2 Computation Function /M1 Legs Isolated RTD /N2 Specifications 12-15Cu10, Cu25 RTD Input /N1 Expansion Inputs /N3 Time When Signal Is Input Procedure Remote Control 5 Points /R112-16 Specifications 12-17 General SpecificationsPower Supply Construction Transport and Storage Conditions General SpecificationsIsolation Supported Standards Standard Performance Specifications 12-19Resolution Excludes Effects of Operating Conditions Other Specifications12-20 220 Dimensional DrawingsSpecifications 12-21 144 151.5 Periodic Printout Scale, recording color, and chart speed Report ModeTime tick and time tick cancel mark Recording color Channel data, alarm, scale printout, and chart speed Scale and chart speed Offset compensation mark, scale, and recording color Printout Using the Tlog Timer /M1 OptionTimer App-4 Time of Recovery Statistical Calculation Operation Operation during Power FailuresProcedure of Handling Over Values during Periodic Printout Special Cases Index Index Index-1 Index Index-2 Index Index-3 7-11 Index-4 WARRANTY/DISCLAIMER Shop online at omega.com