284
MIDI Implementation

General Purpose Controller 8 (Controller number 83)

Status 2nd byte 3rd byte
BnH 53H vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Control value: 00H - 7FH (0 - 127)
* The Tone Level parameter (PATCH/TONE) of Tone 4 will change.

Portamento control (Controller number 84)

Status 2nd byte 3rd byte
BnH 54H kkH
n = MIDI channel number:0H - FH (Ch.1 - 16)
kk = source note number:00H - 7FH (0 - 127)
* A Note-on received immediately after a Portamento Control message will change
continuously in pitch, starting from the pitch of the Source Note Number.
* If a voice is already sounding for a note number identical to the Source Note Number,
this voice will continue sounding (i.e., legato) and will, when the next Note-on is
received, smoothly change to the pitch of that Note-on.
* The rate of the pitch change caused by Portamento Control is determined by the
Portamento Time value.

Effect 1 (Reverb Send Level) (Controller number 91)

Status 2nd byte 3rd byte
BnH 5BH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Reverb Send Level:00H - 7FH (0 - 127)
* In Performance mode the Part Part Reverb Send Level parameter (PERFORM/PART)
will change.

Effect 3 (Chorus Send Level) (Controller number 93)

Status 2nd byte 3rd byte
BnH 5DH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Chorus Send Level:00H - 7FH (0 - 127)
* In Performance mode the Part Part Chorus Send Level parameter (PERFORM/PART)
will change.

RPN MSB/LSB (Controller number 100, 101)

Status 2nd byte 3rd byte
BnH 65H mmH
BnH 64H llH
n = MIDI channel number:0H - FH (Ch.1 - 16)
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended
When using RPNs, first the RPN (Controller numbers 100 and 101; they can be sent in any
This device receives the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB Notes
00H, 00H mmH, llH Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
* In Performance mode, the Part Pitch Bend Range parameter
(PERFORM/PART) will change.
00H, 01H mmH, llH Master Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H (-8192 - 50/ 8192 - 0 -
+8192*50/8192 cent)
* In Performance mode, the Part Fine Tune parameter (PERFORM/
PART) will change.
00H, 02H mmH, llH Master Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
* In Performance mode, the Part Coarse Tune parameter (PERFORM/
PART) will change.
7FH, 7FH ---, --- RPN null
RPN and NRPN will be set as "unspecified". Once this setting has been
made, subsequent
Parameter values that were previously set will not change.
mm, ll: ignored

Program Change

Status 2nd byte
CnH ppH
n = MIDI channel number:0H - FH (Ch.1 - 16)
pp = Program number:00H - 7FH (prog.1 - prog.128)
* Not received in Performance mode when the Receive Program parameter (PERFORM/
MIDI) is OFF.

Channel Pressure

Status 2nd byte
DnH vvH
n = MIDI channel number:0H - FH (Ch.1 - 16)
vv = Channel Pressure:00H - 7FH (0 - 127)
* Not received in Performance mode when the Receive Channel Pressure parameter
(PERFORM/MIDI) is OFF.

Pitch Bend Change

Status 2nd byte 3rd byte
EnH llH mmH
n = MIDI channel number:0H - FH (Ch.1 - 16)
mm, ll = Pitch Bend value:00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
* Not received when the Tone Receive Bender parameter (PATCH/TONE) is OFF.
* Not received in Performance mode when the Receive Bender parameter (PERFORM/
MIDI) is OFF.
Channel Mode Messages
* Not received in Performance mode when the Receive Switch parameter (PERFORM/
MIDI) is OFF.

All Sounds Off (Controller number 120)

Status 2nd byte 3rd byte
BnH 78H 00H
n = MIDI channel number: 0H - FH (Ch.1 - 16)
* When this message is received, all notes currently sounding on the corresponding
channel will be turned off.

Reset All Controllers (Controller number 121)

Status 2nd byte 3rd byte
BnH 79H 00H
n = MIDI channel number: 0H - FH (Ch.1 - 16)
* When this message is received, the following controllers will be set to their reset values.
Controller Reset value
Pitch Bend Change +/-0 (center)
Polyphonic Key Pressure 0 (off)
Channel Pressure 0 (off)
Modulation 0 (off)
Breath Type 0 (min)
Expression 127 (max)
Hold 1 0 (off)
Sostenuto 0 (off)
Soft 0 (off)
Hold 2 0 (off)
RPN unset; previously set data will not change
NRPN unset; previously set data will not change

All Notes Off (Controller number 123)

Status 2nd byte 3rd byte
BnH 7BH 00H
n = MIDI channel number: 0H - FH (Ch.1 - 16)
* When All Notes Off is received, all notes on the corresponding channel will be turned
off. However, if Hold 1 or Sostenuto is ON, the sound will be continued until these are
turned off.