Roland XV-5080 owner manual Performance mode, Rhythm Sets, Performances

Chapter 1 Selecting and Playing a Sound

Rhythm Sets

Rhythm Set	Rhythm Set	Bank Select		Program
Group	Number	Number		Number
		MSB	LSB
USER	1, 2, 3, 4	86	00	1, 2, 3 , 4
PR-A	001, 002	86	64	001, 002
PR-B	001, 002	86	65	001, 002
PR-C	001, 002	86	66	001, 002
PR-D	001, 002	86	67	001, 002
PR-E	001, 002	86	68	001, 002
PR-F	001, 002	86	69	001, 002
PR-G	001, 002	86	70	001, 002
CD-A	1, 2, 3, 4	86	32	1, 2, 3, 4
	:	:	:	::
CD-H	1, 2, 3, 4	86	39	1, 2, 3, 4
XP-A	*1	*1	*1	*1
	:	:	:	::
XP-H	*1	*1	*1	*1

* 1 Depends on the Wave Expansion Board installed. Fixed Bank Select numbers are assigned to the Wave

Expansion Board itself.
Rhythm Set	Rhythm Set	Bank Select
Group	Number	Number
		MSB	LSB
SR-JV80-01	001–128	88	00
SR-JV80-01	129–256	88	01
SR-JV80-02	001–128	88	02
SR-JV80-02	129–256	88	03
:
SR-JV80-65	001–128	90	00
SR-JV80-65	129–256	90	01

In Performance mode

1.Press [PERFORM], getting its indicator to light.

2.Set the transmission channel of your external MIDI device to match the XV-5080’s Performance Control Channel (p. 212).

To learn about the MIDI settings of your external MIDI device, see its owner’s manual.

3.Transmit the appropriate Bank Select MSB (Controller #0) value to the XV-5080.

4.Transmit the appropriate Bank Select LSB (Controller #32) value to the XV-5080.

5.Transmit the Program Change value. The desired Performance will be selected.

*When the XV-5080 receives a Program Change message without Bank Select messages, the corresponding Performance in the currently selected group or bank will be chosen.

You can select any Performance Part’s Patch or Rhythm Set via MIDI. To learn how, refer to “Assigning a different Patch to Part (p. 162)” in the XV-5080 QUICK START.

The Performances in each group correspond to the Bank Select numbers as follows.

Performances

Performance	Performance	Bank Select		Program
Group	Number	Number		Number
		MSB	LSB
USER	001–064	85	00	001–064
PR-A	001–032	85	64	001–032
PR-B	001–032	85	65	001–032
CD-A	001–064	85	32	001–064
	:	:	:	::
CD-H	001–064	85	39	001–064

When Patch/Rhy Rx Ch and Perform Ctrl Ch are set to the same channel, both Bank Select and Program Change are sent, making it possible to switch among Patches, Rhythm Sets, and Performances.

Using MIDI to Switch between Patch, Performance and General MIDI 2 Modes

You can switch between Patch, Performance, and General MIDI 2 modes by transmitting the appropriate System Exclusive (Sys Ex) message to the XV-5080, as listed below. (Sys Ex messages are constructed using hexadecimal notation.)

To switch to Patch/Rhythm Set (Sys Ex.)

F0 41 10 00 10 12 00 00 00 00 01 7F F7

To switch to Performance

F0 41 10 00 10 12 00 00 00 00 00 00 F7

To switch to GM2 mode

F0 41 10 00 10 12 00 00 00 00 03 7F F7

The third byte of the MIDI message indicates the device ID number, and the factory setting is “10.” (This is “10” in hexadecimal notation; in decimal this would be 16.) (This device ID number will appear as 17 in the display of the XV- 5080. The transmitted messages will use a value of one less than this (16).) If you have modified the device ID number (p.

22