Chapter 4 Creating Patches

Fade (LFO Fade)

Mode (LFO Fade Mode)

Sets how the LFO will be applied.

Available Settings:

ON-IN:The LFO will fade in after the key is pressed.

high (more)

Delay

Fade

Time

Time

 

 

Depth

WG Pitch /

 

 

TVF Cutoff Frequency /

 

 

TVA Level / TVA Pan

key is

 

 

 

low (less)

pressed

 

 

 

ON-OUT:The LFO will be immediately applied when the key is pressed, and will then fade out.

high (more)

Delay Time

Fade Time

WG Pitch /

 

Depth

TVF Cutoff Frequency /

 

 

TVA Level / TVA Pan

key is

 

 

 

low (less)

pressed

 

 

 

OFF-IN:The LFO will fade in after the key is released.

high (more)

 

Delay

Fade

 

Time

Time

 

 

WG Pitch /

 

 

Depth

 

 

 

TVF Cutoff Frequency /

 

 

 

TVA Level / TVA Pan

key is

key is

 

low (less)

pressed

released

 

 

 

 

OFF-OUT:The LFO will be immediately applied when the

key is pressed, and will begin fading out when the key is

released.

high (more)

 

Delay

Fade

 

Time

Time

 

 

WG Pitch /

 

 

Depth

TVF Cutoff Frequency /

key is

key is

 

TVA Level / TVA Pan

 

low (less)

pressed

released

 

 

 

 

Time (LFO Fade Time)

Range: 0–127

This adjusts the time over which the LFO rises to its full effect or fades away. (Refer to the diagrams for Fade Mode.)

Key Sync (LFO Key Sync)

Range: OFF/ON

Specifies whether you want the LFO cycle to start in sync with the timing of a key press (ON), or not (OFF).

Depth (LFO Depth)

Pitch (Pitch LFO Depth)

Range: -63– +63

Adjusts how much the LFO will affect the WG Pitch.

TVF (TVF LFO Depth)

Range: -63– +63

Adjusts how much the LFO will affect the Tone’s TVF cutoff frequency.

TVA (TVA LFO Depth)

Range: -63– +63

Adjusts how much the LFO will affect the Tone’s TVA Level.

Pan (Pan LFO Depth)

Range: -63– +63

Adjusts how much the LFO will affect the Tone’s TVA Pan.

PATCH LFO&Ctrl #1/#2 page ([PATCH] - [F5 (LFO&Ctl)] - [F3 (Control)])

Matrix Control 1–4

Source (Matrix Control Source)

Assign one of the following controllers to Matrix Control Source. If you wish to use a controller that will apply to all Patches, or a controller that cannot be directly selected here, select SYS-CTRL1–4, and then select the controller using the System Control Source parameters (System Control Screen).

Available Settings:

OFF: No controller is used.

CC01–CC95:Controller numbers 1–95 (except for 32)

PITCH BEND: Pitch Bend

AFTERTOUCH: Aftertouch

SYS-CTRL1:System controller 1

SYS-CTRL2:System controller 2

SYS-CTRL3:System controller 3

SYS-CTRL4:System controller 4

VELOCITY: Velocity

KEYFOLLOW: Keyfollow

TEMPO: Tempo

LFO1

LFO2

146

Page 146
Image 146
Roland XV-5080 owner manual Creating Patches Fade LFO Fade, Key Sync LFO Key Sync, Depth LFO Depth, 146