Canon 3260 V. INSTALLATION, 1 - 9

V. INSTALLATION

A. Notes

This printer is packaged and shipped from the factory after careful adjustments and rigorous

inspections.

When installing the printer, it is important to demonstrate its performance in the same way as

when it passes the factory inspection.

The service engineer must sufficiently understand the performance of the printer, install it

correctly in a location with an appropriate environment, and conduct sufficient checks of the

unit.

B. Location Selection

Before taking the printer to the customer's premises, you should confirm the following condi-

tions at the installation location.

1. Power supply

Use the following power supplies:

• Alternating current (AC): -10%, +6% of the rated voltage

• Power frequency: 50/60Hz±2Hz

2. Operating environment

Install in a location that meets the following conditions:

• Level, flat surface

• Temperature, humidity within the following ranges:

Surrounding temperature: 10to 32.5°C

Surrounding humidity: 20 to 80%RH (relative humidity), without condensation

• Cool, well-ventilated space

Do not install in the following locations:

• Exposed to direct sunlight

If you cannot avoid such a location, hang heavy curtains, etc. to shut out the direct sunlight.

• Near magnets and devices that emit a magnetic field.

• Areas with vibration

• Dusty places

• Near fire or water

3. Installation space

Install the printer a suitable distance from the wall, leaving enough room to operate it (see Figure

1-5-1).

When installing the printer on a desk, etc., be sure that it is large enough to accommodate

the printer's feet (rubber pads) and sturdy enough to hold its weight.

1 - 9

CHAPTER 1

Contents

Main Page PREFACE Page CONTENTS CHAPTER 1 PRODUCT INFORMATION CHAPTER 2 OPERATION AND TIMING CHAPTER 3 THE MECHANICAL SYSTEM CHAPTER 4 TROUBLESHOOTING APPENDIX Page Page Page I. FEATURES 1 - 1 Page II. SPECIFICATIONS 1 - 3 1 - 4 1 - 5 III. SAFETY INFORMATION ! 1 - 6 IV. PARTS OF THE PRINTER 1 - 7 1 - 8 V. INSTALLATION 1 - 9 Figure 1-5-1 1 - 10 1 - 11 Page 1 - 13 1 - 14 1 - 15 1 - 16 Page VI. MAINTENANCE AND SERVICING BY THE CUSTOMER 1 - 18 1 - 19 Page VII. OPERATION 1 - 21 1 - 22 1 - 23 1 - 24 1 - 25 Page CHAPTER 1 1-27 Figure 1-7-2 ** Page CHAPTER 2 OPERATION AND TIMING Page I. BASIC OPERATION 2 - 1 2 - 2 Purpose Remark Period 2 - 3 II. ENGINE CONTROL SYSTEM 2 - 4 3. DC Controller Input/Output Signals Figure 2-2-2 2 - 5 Figure 2-2-3 2 - 6 Figure 2-2-4 MT1 2 - 7 Figure 2-2-5 2 - 8 CL1 SL1 CL2 SMT1 2 - 9 SL2 SL3 2 - 10 2 - 11 2 - 12 2 - 13 2 - 14 Page C. High-Voltage Power Supply Figure 2-2-10 2 - 16 2 - 17 2 - 18 D. Power Supply 1. Outline 2 - 19 Power supply Low-voltage power supply circuit Tofixing roller heater DC controller 2 - 20 2 - 21 2 - 22 M 2 - 23 2 - 24 IC202 (G.A.) IC201 (CUP) Page III. LASER/SCANNER SYSTEM 2 - 26 2 - 27 2 - 28 2 - 29 2 - 30 Page IV. IMAGE FORMATION SYSTEM 2 - 32 Figure 2-4-1 2 - 33 2 - 34 5. Drum cleaning stage Step 8 Drum cleaning Figure 2-4-4 2 - 35 2 - 36 2 - 37 2 - 38 2 - 39 2 - 40 2 - 41 V. PICK-UP/FEED SYSTEM 2 - 42 Figure 2-5-1 2 - 43 Figure 2-5-2 2 - 44 SL2 SL3 SMT1 SL1 CL2 CL3 2 - 45 Figure 2-5-4 Figure 2-5-5 2 - 46 STBY INTR PRINT STBY LSTR (Unit:Seconds) Power switchON Pick-up timing from the upper cassette (A4 : tow pages continuously print) 2 - 47 2 - 48 2 - 49 2 - 50 2 - 51 2 - 52 2 - 53 2 - 54 2 - 55 2 - 56 2 - 57 MT1 2 - 58 2 - 59 2 - 60 VI. OVERALL CONTROL SYSTEM 2 - 61 2 - 62 2-63 Video contoroller PCB Block Diagram Note <J1> AIR <J11> ASIC <J6/7> <J8> Page 2 - 65 2 - 66 2 - 67 Page Page Page I. PREFACE 3 - 1 II. EXTERNALS 3 - 2 3 - 3 3 - 4 3 - 5 3 - 6 3 - 7 III. MAIN UNITS 3 - 8 3 - 9 3 - 10 3 - 11 a 3 - 12 3 - 13 3 - 14 IV. MAIN PARTS 3 - 15 3 - 16 3 - 17 3 - 18 3 - 19 3 - 20 3 - 21 3 - 22 3 - 23 V. SWITCHES/SENSORS 3 - 24 3 - 25 3 - 26 3 - 27 3 - 28 3 - 29 Page Page 3 - 32 3 - 33 3 - 34 VII. MOTORS/FANS 3 - 35 3 - 36 3 - 37 3 - 38 3 - 39 3 - 40 VIII. PCBS 3 - 41 3 - 42 3 - 43 3 - 44 3 - 45 3 - 46 3 - 47 3 - 48 CHAPTER 4 TROUBLESHOOTING Page I. PREFACE 4 - 1 Figure 4-1-1 4 - 2 4 - 3 4 - 4 4 - 5 4 - 6 Figure 4-1-3 4 - 7 Canon Inc., LBP-3260 Printer Configuration Page II. IMAGE DEFECTS 4 - 8 4 - 9 4 - 10 4 - 11 4 - 12 Table 4-2-2 4 - 13 Page 4 - 15 4 - 16 4 - 17 IV. PAPER TRANSPORT TROUBLESHOOTING 4 - 18 Page V. MALFUNCTION TROUBLESHOOTING 4 - 20 VI. MALFUNCTION STATUS TROUBLESHOOTING 4 - 21 4 - 22 4 - 23 4 - 24 4 - 25 4 - 26 4 - 27 VII. MEASUREMENT AND ADJUSTMENT 4 - 28 4 - 29 4 - 30 4 - 31 4 - 32 4. High-voltage power supply PCB Figure 4-7-6 Table 4-7-4 4 - 33 Page VIII. MAINTENANCE AND SERVICING 4 - 35 4 - 36 4 - 37 4 - 38 4 - 39 Tool No. Application/r emarks 1 Printer driver tester RY9-0104 No. Tool name RY9-0104 Usedfor checking printer operations. Shape RANK B 4 - 40 4 - 41 4 - 42 Clip 4 - 43 DATA DATASET Connector 1 RY9-0104 DC24V 4 - 44 PRINTER DRIVER 4 - 45 RY9-0104 PRINTER DRIVER Table 4-8-7 Table 4-8-8 4 - 46 Mode select 8 H. Solvents and Oil List Table 4-8-9 4 - 47 IX. LOCATION OF CONNECTORS 4 - 48 4 - 49 Page Page Page A-1 Timing chart for two consecutive prints on A4 paper (Lower cassette feed - face-down tray delivery) I. GENERAL TIMING CHART (Unit: Seconds) Page 654321 D C Ferritecore ToHVT Fixingsub heater 654321 D C (option) Expansion interface board J1 III. LIST OF SIGNALS A. Input/output signals to/from DC controller PCB A - 5 A - 6 A - 7 A - 8 A - 9 Page IV. MESSAGES TABLE A - 11 A - 12 Note: A - 13 A - 14 A - 15 Note: A - 16 A - 17 A - 18 Note: A - 19 A - 20