Canon 3260 4 - 27

VI-17. "PRINTER OPEN" message appears when the cover is closed.

<Possible causes>

1. The projection for the delivery cover is damaged.

Action: Replace the delivery cover.

2. The projection for the upper cover is damaged.

Action: Replace the upper cover.

3. The projection for the pick-up unit door is damaged.

Action: Replace the pick-up unit door.

4. The pick-up unit door sensor is defective.

Action: Using the printer driver tester, check the condition of the sensor. If the LED of the

tester does not light up when the pick-up unit door is opened, replace the sensor.

5. Interlock arm does not move smoothly, or is damaged.

Action: Adjust the arm so that it moves smoothly. Replace it if damaged.

6. Connector is loose.

Action: Reconnect connector J1401 on the switch/sensor PCB and connectors J205 and

J221 on the DC controller PCB.

7. The door switch is defective.

Action: Replace the switch/sensor PCB.

8. The DC controller PCB is defective.

Action: Replace the DC controller PCB.

4 - 27

CHAPTER 4

Contents

Main Page PREFACE Page CONTENTS CHAPTER 1 PRODUCT INFORMATION CHAPTER 2 OPERATION AND TIMING CHAPTER 3 THE MECHANICAL SYSTEM CHAPTER 4 TROUBLESHOOTING APPENDIX Page Page Page I. FEATURES 1 - 1 Page II. SPECIFICATIONS 1 - 3 1 - 4 1 - 5 III. SAFETY INFORMATION ! 1 - 6 IV. PARTS OF THE PRINTER 1 - 7 1 - 8 V. INSTALLATION 1 - 9 Figure 1-5-1 1 - 10 1 - 11 Page 1 - 13 1 - 14 1 - 15 1 - 16 Page VI. MAINTENANCE AND SERVICING BY THE CUSTOMER 1 - 18 1 - 19 Page VII. OPERATION 1 - 21 1 - 22 1 - 23 1 - 24 1 - 25 Page CHAPTER 1 1-27 Figure 1-7-2 ** Page CHAPTER 2 OPERATION AND TIMING Page I. BASIC OPERATION 2 - 1 2 - 2 Purpose Remark Period 2 - 3 II. ENGINE CONTROL SYSTEM 2 - 4 3. DC Controller Input/Output Signals Figure 2-2-2 2 - 5 Figure 2-2-3 2 - 6 Figure 2-2-4 MT1 2 - 7 Figure 2-2-5 2 - 8 CL1 SL1 CL2 SMT1 2 - 9 SL2 SL3 2 - 10 2 - 11 2 - 12 2 - 13 2 - 14 Page C. High-Voltage Power Supply Figure 2-2-10 2 - 16 2 - 17 2 - 18 D. Power Supply 1. Outline 2 - 19 Power supply Low-voltage power supply circuit Tofixing roller heater DC controller 2 - 20 2 - 21 2 - 22 M 2 - 23 2 - 24 IC202 (G.A.) IC201 (CUP) Page III. LASER/SCANNER SYSTEM 2 - 26 2 - 27 2 - 28 2 - 29 2 - 30 Page IV. IMAGE FORMATION SYSTEM 2 - 32 Figure 2-4-1 2 - 33 2 - 34 5. Drum cleaning stage Step 8 Drum cleaning Figure 2-4-4 2 - 35 2 - 36 2 - 37 2 - 38 2 - 39 2 - 40 2 - 41 V. PICK-UP/FEED SYSTEM 2 - 42 Figure 2-5-1 2 - 43 Figure 2-5-2 2 - 44 SL2 SL3 SMT1 SL1 CL2 CL3 2 - 45 Figure 2-5-4 Figure 2-5-5 2 - 46 STBY INTR PRINT STBY LSTR (Unit:Seconds) Power switchON Pick-up timing from the upper cassette (A4 : tow pages continuously print) 2 - 47 2 - 48 2 - 49 2 - 50 2 - 51 2 - 52 2 - 53 2 - 54 2 - 55 2 - 56 2 - 57 MT1 2 - 58 2 - 59 2 - 60 VI. OVERALL CONTROL SYSTEM 2 - 61 2 - 62 2-63 Video contoroller PCB Block Diagram Note <J1> AIR <J11> ASIC <J6/7> <J8> Page 2 - 65 2 - 66 2 - 67 Page Page Page I. PREFACE 3 - 1 II. EXTERNALS 3 - 2 3 - 3 3 - 4 3 - 5 3 - 6 3 - 7 III. MAIN UNITS 3 - 8 3 - 9 3 - 10 3 - 11 a 3 - 12 3 - 13 3 - 14 IV. MAIN PARTS 3 - 15 3 - 16 3 - 17 3 - 18 3 - 19 3 - 20 3 - 21 3 - 22 3 - 23 V. SWITCHES/SENSORS 3 - 24 3 - 25 3 - 26 3 - 27 3 - 28 3 - 29 Page Page 3 - 32 3 - 33 3 - 34 VII. MOTORS/FANS 3 - 35 3 - 36 3 - 37 3 - 38 3 - 39 3 - 40 VIII. PCBS 3 - 41 3 - 42 3 - 43 3 - 44 3 - 45 3 - 46 3 - 47 3 - 48 CHAPTER 4 TROUBLESHOOTING Page I. PREFACE 4 - 1 Figure 4-1-1 4 - 2 4 - 3 4 - 4 4 - 5 4 - 6 Figure 4-1-3 4 - 7 Canon Inc., LBP-3260 Printer Configuration Page II. IMAGE DEFECTS 4 - 8 4 - 9 4 - 10 4 - 11 4 - 12 Table 4-2-2 4 - 13 Page 4 - 15 4 - 16 4 - 17 IV. PAPER TRANSPORT TROUBLESHOOTING 4 - 18 Page V. MALFUNCTION TROUBLESHOOTING 4 - 20 VI. MALFUNCTION STATUS TROUBLESHOOTING 4 - 21 4 - 22 4 - 23 4 - 24 4 - 25 4 - 26 4 - 27 VII. MEASUREMENT AND ADJUSTMENT 4 - 28 4 - 29 4 - 30 4 - 31 4 - 32 4. High-voltage power supply PCB Figure 4-7-6 Table 4-7-4 4 - 33 Page VIII. MAINTENANCE AND SERVICING 4 - 35 4 - 36 4 - 37 4 - 38 4 - 39 Tool No. Application/r emarks 1 Printer driver tester RY9-0104 No. Tool name RY9-0104 Usedfor checking printer operations. Shape RANK B 4 - 40 4 - 41 4 - 42 Clip 4 - 43 DATA DATASET Connector 1 RY9-0104 DC24V 4 - 44 PRINTER DRIVER 4 - 45 RY9-0104 PRINTER DRIVER Table 4-8-7 Table 4-8-8 4 - 46 Mode select 8 H. Solvents and Oil List Table 4-8-9 4 - 47 IX. LOCATION OF CONNECTORS 4 - 48 4 - 49 Page Page Page A-1 Timing chart for two consecutive prints on A4 paper (Lower cassette feed - face-down tray delivery) I. GENERAL TIMING CHART (Unit: Seconds) Page 654321 D C Ferritecore ToHVT Fixingsub heater 654321 D C (option) Expansion interface board J1 III. LIST OF SIGNALS A. Input/output signals to/from DC controller PCB A - 5 A - 6 A - 7 A - 8 A - 9 Page IV. MESSAGES TABLE A - 11 A - 12 Note: A - 13 A - 14 A - 15 Note: A - 16 A - 17 A - 18 Note: A - 19 A - 20