Dell TL2000 manual 10-14

5-26.	The 4U library Monitor Library: Drive			10-2.	Shipping lock and label	.	10-2
	Identity page showing one Fibre Channel			10-3.	Library drive sled without ElectroStatic
	drive (#1) and one SCSI drive (#2). . .	. 5-33			Discharge (ESD) springs (SCSI sled shown)		10-3
5-27.	The 4U library Monitor Library: Library			10-4.	Library drive sled with ESD springs [1]
	Status page	.	5-34		(SAS sled shown)	.	10-4
5-28.	The 4U library Monitor Library: Drive			10-5.	Drive sled components (full-high fibre
	Status page	.	5-36		drive in top position, half-high SCSI drive
5-29.	The 2U library Monitor Library: Inventory				in middle position, half-high SAS drive in
	page	.	5-37		bottom position) on back panel of a 4U
5-30.	The 4U library Monitor Library: Inventory				library	.	10-4
	page	.	5-38	10-6.	Pulling the drive sled out of the library
5-31.	The 4U library Configure Library: General				(drive sled without ESD springs shown)	. 10-5
	and Extended page	.	5-40	10-7.	Pushing the drive sled into the library
5-32.	The 4U library Configure Library: Logical				(drive sled without ESD springs shown)	. 10-6
	Libraries page	.	5-40	10-8.	Diagrams for applying conductive tape for
5-33.	The 4U library Configure Library: Path				ESD protection to the back of a drive sled
	Failover page	.	5-41		installed in a 2U or 4U library . . . .	.	10-7
5-34.	Path Failover license verification page		5-41	10-9.	A power supply being removed from a 2U
5-35.	Feature Activation Key screen . . . .	.	5-42		library	.	10-8
5-36.	Configure Library: Encryption Feature			10-10.	A Library Controller Card being removed
	configuration screen	.	5-42		from the library	.	10-9
5-37.	The Configure Library: Drive page for a			10-11.	Rear panel of a 4U library with a Fibre
	4U library	.	5-44		Channel full height drive in the top
5-38.	Configure Library: Network page		5-45		position, a SCSI half height drive in the
5-39.	Warning screen	.	5-45		middle position, and a SAS half height
5-40.	Configure Library: User Access page		5-47		drive in the bottom position . . . .	. 10-11
5-41.	The Configure Library: Date & Time page		5-47	10-12.	Removing the two mounting bracket
5-42.	Configure Library: Logs & Traces page		5-48		screws anchoring the library to the rack
5-43.	Configure Library: Event Notification page		5-48		(one screw on each side of the library .	. 10-11
5-44.	Configure Library: Restore Defaults page		5-49	10-13.	Foot pads installed on the bottom of the
5-45.	Manage Library: Move Media page		5-49		library enclosure	. 10-13
5-46.	Manage Library: Perform Inventory page		5-50	10-14.	Removing the shipping label and lock
5-47.	Manage Library: Release Magazine page		5-50		from the top of the library and storing on
5-48.	Service Library: Clean Drive page		5-51		the rear panel	.	10-14
5-49.	Service Library: View Logs page		5-51	10-15.	Library shipping lock and label storage
5-50.	Service Library: View Drive Logs screen		5-52		location on the real panel of the library	. 10-14
5-51.	Service: Save Drive Dump	. 5-52		10-16.	Removing a Library Controller Card from
5-52.	Service Library: Perform Diagnostics page		5-53		the library	.	10-16
5-53.	Service Library: Perform Key Path			10-17.	Library Front Panel LEDs	. 10-17
	Diagnostics page	.	5-53	10-18.	Removing a drive sled from the library
5-54.	The 2U library Service Library: Upgrade				(drive sled without ESD springs shown)	. 10-18
	Firmware page	.	5-54	10-19.	Drive sled taping diagrams . . . .	.	10-19
5-55.	The 4U library Service Library: Upgrade			10-20.	Access hole for the left magazine (facing
	Firmware page	.	5-55		rear of library)	.	10-20
5-56.	Service Library: Reboot page . . . .	. 5-55		10-21.	Access hole for the right magazine (facing
6-1.	The LTO Ultrium 800 GB Data Cartridge		6-1		rear of library)	.	10-21
6-2.	Ultrium WORM Tape Cartridge . . . .	. 6-3		10-22.	Left magazine pulled out of a 4U library
6-3.	Sample bar code label on the LTO Ultrium 4				(facing front of library)	. 10-22
	Tape Cartridge	. 6-5		10-23.	A power supply being removed from a
6-4.	Setting the write-protect switch . . . .	.	6-6		library	.	10-23
6-5.	Double-boxing tape cartridges for shipping		6-7	10-24.	Mounting brackets and anchors for
6-6.	Checking for gaps in the seams of a				securing the library in a rack (one bracket
	cartridge	.	6-8		and anchor on each side of the library).	.	10-24
7-1.	A 250w power supply with LEDs		7-8	10-25.	Front view of a rack showing the rails
7-2.	A 80w power supply without LEDs		7-9		installed	.	10-24
9-1.	Access holes for the left magazine		9-2	A-1.	Configuration of a One Partition System		A-3
9-2.	Access holes for the right magazine		9-3	A-2.	Configuration of a Two Partition System		A-4
9-3.	Left Magazines pulled out of the 2U library		9-4	A-3.	Configuration of a Three Partition System		A-4
9-4.	Left Magazines pulled out of the 4U Library		9-4	A-4.	Configuration of a Four Partition System		A-5
10-1.	Shipping lock and label storage location		10-2	A-5.	Examples of SCSI Element Addressing		A-5

viiiDell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide