Lincoln Electric SVM175-A Options / Accessories, Field Installed Options, TIG Welding Accessories

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

C-2		ACCESSORIES			C-2
OPTIONS / ACCESSORIES				T12153-9 50 AMP, 120/240V POWER PLUG -
FIELD INSTALLED OPTIONS				Provides one dual voltage plug for full KVA power.
The following options/accessories are available for				TIG WELDING ACCESSORIES
your Ranger 305D from your Lincoln distributor.				K1783-9 TIG TORCH - For TIG welding with shielding
K957-1 HEAVY DUTY, TWO WHEEL TRAILER FOR				gas. Includes 25 feet of cable.
SMALL WELDERS - For road, off-road and in-plant				K963-2 - Hand Amptrol.
and yard towing. (For highway use, consult applicable				K870 - Foot Amptrol
federal, state and local laws regarding requirements
for brakes, lights, fenders, etc.)				NOTE: TIG welding requires a MagnumTM TIG Gun,
K1737-1 FOUR-WHEEL ALL-TERRAIN UNDERCAR-				appropriate Magnum Parts Kit and argon gas.
RIAGE - For moving by hand.				SEMIAUTOMATIC FCAW AND MIG
K1770-1 UNDERCARRIAGE (FACTORY) - For moving				WELDING ACCESSORIES
by hand on a smooth surface. One or two gas cylinders				LN-25 WIRE FEEDER K449 - This portable unit pro-
can be mounted on the rear of the undercarriage with the				vides CC/CV for flux-cored arc welding (FCAW) and
installation of K1745-1 Cylinder Holder(s).				metal inert gas welding (MIG). Includes a gas solenoid
K1739-1 CABLE CARRIER KIT - For use on K1737-1				and an internal contactor that allows across-the-arc
				operation with no control cable. The LN-25 provides a
and K1770-1 Undercarriages.				“cold” electrode until the gun trigger is pressed. For
K1745-1 SINGLE GAS CYLINDER HOLDER - For use				voltage control at the feeder, a K444-1 Remote Voltage
on K1770-1 Undercarriage. One or tow may be installed				Control Kit or K857 Remote Control is required. Refer
on an undercarriage.				to connection instructions later in this section.
K1789-1 ROLL CAGE - Gives added damage protection.				LN-7 OR LN-8 WIRE FEEDER - Semiautomatic, con-
K886-2 CANVAS COVER -	Protects machine when			stant speed wire feeders.
not in use.				NOTE: Gas-shielding welding requires a Magnum
K1898-1 SPARK ARRESTER - Attaches between				Gun. Gasless welding requires an Innershield Gun.
muffler or exhaust elbow.				LN-742 WIRE FEEDER - A semiautomatic wire feeder
K704 ACCESSORY KIT - Accessory set includes 35 ft.				with “cold” electrode. Refer to connection instructions
				later in this section.
(10.7meters) 2 AWG electrode cable, 30 ft. (9.1				MAGNUM SPOOL GUN (K487-25) - A lightweight,
meters) 2 AWG work cable, headshield with No. 12 fil-
ter, G300 work clamp and Cooltong 300 electrode				semiautomatic wire feeder for aluminum welding with
holder. Cables are rated at 300 amps, 40% duty cycle.				argon gas.	Has built-in remote wire speed control in
K857 28 ft (8.5m) or K857-1 100 ft. (30.4m)				the handle.	Requires the K488 SG Control Module.
REMOTE CONTROL - Portable control provides same				Refer to connection instructions later in this section.
dial range as the output control on the welder. Has a				SG CONTROL MODULE (K488) - Controls wire speed
convenient 6-pin plug for easy connection to the				and gas flow. Provides the required control interface
welder.				between the Ranger 305D and the K487-25 Magnum
K1690-1 GFCI RECEPTACLE KIT - Includes one UL				Spool Gun. Requires the K691-10 Input Cable.
				K444-1 REMOTE VOLTAGE CONTROL - Provides
approved 120 volt ground fault circuit interrupter
duplex type receptacle with cover and installation				voltage adjustment control at the feeder. Includes 25
instructions. Replaces the	factory installed		120V	feet of cable.
duplex receptacle. Each receptacle of the			GFCI	K126-2 INNERSHIELD GUN - For gasless welding.
Duplex is rated at 20 amps. The maximum total cur-				Includes 15 feet of cable.
rent from the GFCI Duplex is limited to 20 amps. Two				K470-2 MAGNUM GUN CONNECTOR KIT - For gas-
kits are required.				shielding welding.
K802-N POWER PLUG KIT - Provides four 120 volt				K466-1 MAGNUM GUN CONNECTOR KIT - For con-
plugs rated at 20 amps each and one dual voltage, full
KVA plug rated at 120/240 volts, 50 amps.				necting the Magnum 300 MIG Gun to the feeder for
K802-R POWER PLUG KIT - Provides four 120 volt				gas-shielding welding.
plugs rated at 15 amps each and one dual voltage, full
KVA plug rated at 120/240 volts, 50 amps.			RANGER 305D